Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A car driving at 80 km/h brakes with a constant deceleration of 5.5 m/s² until it stops. Find the braking distance s.
v₀ = 80 km/ha = −5.5 m/s²v = 0
s = m
2.KinematicsHard
A tram starts from rest and accelerates at 3 m/s² for 5 s, then runs at constant speed for 20 s, and finally brakes at 3 m/s² until it stops. Find the total travel time t.
a1 = 3 m/s²t1 = 5 st2 = 20 sa3 = −3 m/s²
t = s
3.Newton’s lawsMedium
A 14 kg block slides down a slope at 20° to the horizontal. The coefficient of kinetic friction is 0.25. Use g = 9.81 m/s². Find the acceleration a of the block along the slope.
m = 14 kgθ = 20°μ = 0.25g = 9.81 m/s²
a = m/s²
4.Newton’s lawsHard
Two blocks on a level floor are joined by a light horizontal string. A horizontal force of 140 N pulls the front 9 kg block; the 7 kg block is towed behind. The coefficient of kinetic friction is 0.3 for both blocks. Use g = 9.81 m/s². Find the acceleration a of the blocks.
m1 = 7 kgm2 = 9 kgF = 140 Nμ = 0.3g = 9.81 m/s²
a = m/s²
5.Projectile motionMedium
A ball is launched at 65° above horizontal from level ground. Ignore air resistance. Find the maximum height H the ball reaches.
v0 = 20 m/sθ = 65°g = 9.81 m/s²
H = m
6.Projectile motionHard
A ball is thrown from ground level at 30 m/s and 65° above the horizontal. It lands on the flat roof of a building 14 m high, on its way down. Ignore air resistance and use g = 9.81 m/s². Find the horizontal distance x from the launch point to where it lands.
v₀ = 30 m/sθ = 65°hroof = 14 mg = 9.81 m/s²
x = m
7.Work & energyMedium
A block slides from rest down a slope at 35° to the horizontal. The coefficient of kinetic friction is 0.3. Find its speed v after it has slid 5 m along the slope.
θ = 35°μ = 0.3d = 5 mg = 9.81 m/s²
v = m/s
8.Work & energyHard
A spring of stiffness 800 N/m at the bottom of a 15° slope is compressed by 20 cm against a 1 kg block and released. The coefficient of kinetic friction between block and slope is 0.15. How far d up the slope does the block travel from the release point before it stops? (Ignore the short distance over which the spring pushes, i.e. take friction and gravity over the whole distance d.)
A 5 kg glider moving at 11 m/s makes a perfectly elastic head-on collision with a 1 kg glider at rest on a frictionless track. Find the velocity v′2 of the second glider after the collision.
m1 = 5 kgm2 = 1 kgv1 = 11 m/sv2 = 0
v′2 = m/s
10.Momentum & collisionsHard
At a crossing a 1900 kg car travelling east at 24 m/s collides with a 1000 kg car travelling north at 10 m/s. The cars lock together. Find the speed v′ of the wreck just after the collision.
m1 = 1900 kgv1 = 24 m/s (E)m2 = 1000 kgv2 = 10 m/s (N)
v′ = m/s
11.Hydrostatic forceMedium
A vertical rectangular gate 2 m wide sits in the wall of a tank of water, with its top edge 0.5 m below the surface. Find the resultant hydrostatic force F on the gate.
A vertical rectangular gate 1 m wide sits in the wall of a tank of oil, with its top edge 0.5 m below the surface. Find the depth ycp of the centre of pressure below the surface.
d = 0.5 mH = 2 mb = 1 mρ = 880 kg/m³g = 9.81 m/s²
ycp = m
13.Continuity & BernoulliMedium
Water flows through a horizontal pipe that narrows from 75 mm to 25 mm. In the wide section the pressure is 320 kPa and the velocity is 1.25 m/s. Ignoring losses, find the pressure p2 in the narrow section.
A fountain nozzle points straight up. Just below the nozzle the supply pipe has a diameter of 75 mm and a gauge pressure of 30 kPa. The nozzle exit diameter is 40 mm, and the height difference across the nozzle is negligible. Ignoring losses and air resistance, find the height H the jet rises above the nozzle. Use g = 9.81 m/s².
A heat engine works between a hot reservoir at 725 °C and a cold reservoir at 25 °C. It takes in 3600 kJ of heat. Find the most work Wmax it could possibly produce.
TH = 725 °CTL = 25 °CQH = 3600 kJ
Wmax = kJ
18.Heat engines & refrigeratorsHard
A heat engine takes in 2300 kJ of heat from a reservoir at 900 °C, produces 1219 kJ of work and rejects the rest to a reservoir at 10 °C, per cycle. Find the total entropy generated Sgen per cycle.
TH = 900 °CTL = 10 °CQH = 2300 kJW = 1219 kJ
Sgen = kJ/K
19.Waves, sound & opticsMedium
A small loudspeaker radiates 0.2 W of sound power equally in all directions. Find the sound intensity level β at 8 m.
P = 0.2 Wr = 8 mI0 = 10⁻¹² W/m²
β = dB
20.Waves, sound & opticsHard
Light of wavelength 532 nm falls at right angles on a grating with 500 lines per millimetre. Find the angle θ2 of the order-2 maximum.
N = 500 mm⁻¹λ = 532 nmm = 2
θ2 = °
3Solutions
1.Kinematics
Answer: s = 44.89 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Units
v₀ = 80/3.6 = 22.22 m/s
Braking distance
0 = v₀² − 2·a·s → s = v₀²/(2a) = 22.22²/(2·5.5) = 44.89 m
Answer
s = 44.89 m
2.Kinematics
Answer: t = 30 s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Top speed
v = a1·t1 = 3·5 = 15 m/s
Braking time
t3 = v/a3 = 15/3 = 5 s
Total time
t = 5 + 20 + 5 = 30 s
Answer
t = 30 s
3.Newton’s laws
Answer: a = 1.051 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 20·cos 65° = 8.452 m/s
vy = v0·sin θ = 20·sin 65° = 18.13 m/s
Highest point
At the top the vertical velocity is zero: vy² = 2gH.
H = vy²/(2g) = 18.13²/(2·9.81) = 16.75 m
Answer
H = 16.75 m
6.Projectile motion
Answer: x = 63 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
vx = 12.68 m/s, vy = 27.19 m/s
Time to land on the roof
Larger root: the ball is descending.
14 = 27.19·t − 4.905·t²
t = (27.19 + √(27.19² − 2·9.81·14))/9.81 = 4.969 s
Horizontal distance
x = vx·t = 12.68·4.969 = 63 m
Answer
x = 63 m
7.Work & energy
Answer: v = 5.671 m/s
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy balance along the slope
The block drops a height d·sin θ while friction removes μmg·cos θ·d. The mass cancels.
½v² = g·d·(sin θ − μ·cos θ)
v = √(2·9.81·5·(0.5736 − 0.3·0.8192)) = 5.671 m/s
Answer
v = 5.671 m/s
8.Work & energy
Answer: d = 4.04 m
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Spring energy
x = 20 cm = 0.2 m
½kx² = ½·800·0.2² = 16 J
Energy balance along the slope
m·g = 1·9.81 = 9.81 N
½kx² = mg·d·(sin θ + μ·cos θ)
d = 16/(9.81·(0.2588 + 0.15·0.9659)) = 4.04 m
Answer
d = 4.04 m
9.Momentum & collisions
Answer: v′2 = 18.33 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Elastic collision with a target at rest
Solving momentum and energy conservation together gives these two results.
v′1 = (5 − 1)/(5 + 1)·11 = 7.333 m/s
v′2 = 2·5/(5 + 1)·11 = 18.33 m/s
Answer
v′2 = 18.33 m/s
10.Momentum & collisions
Answer: v′ = 16.1 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Exit velocity
β = 40/75 = 0.5333
v2 = √(2p1/(ρ(1 − β⁴))) = √(2·30000/(1000·0.9191)) = 8.08 m/s
Height of the jet
Bernoulli along the jet: at the top the velocity is zero and the pressure is atmospheric again.
H = v2²/(2g) = 8.08²/(2·9.81) = 3.327 m
Answer
H = 3.327 m
15.Ideal gas law
Answer: P = 326.5 kPa
Ideal gas law: PV = nRT, with n = m/M.
Moles
n = m/M = 230/32 = 7.188 mol
T = 0 + 273.15 = 273.1 K
Pressure
P = nRT/V = 7.188·8.314·273.1/0.05 = 326.5 kPa
Answer
P = 326.5 kPa
16.Ideal gas law
Answer: V2 = 4.795 L
Combined gas law: for a fixed amount of ideal gas, P1V1/T1 = P2V2/T2.
Absolute temperatures
T1 = 288.1 K, T2 = 513.1 K
Combined gas law
V2 = V1·(P1/P2)·(T2/T1) = 5·(350/650)·(513.1/288.1) = 4.795 L
Answer
V2 = 4.795 L
17.Heat engines & refrigerators
Answer: Wmax = 2525 kJ
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 725 + 273.15 = 998.1 K
TL = 25 + 273.15 = 298.1 K
Carnot efficiency
ηmax = 1 − TL/TH = 1 − 298.1/998.1 = 70.13 %
Maximum work
Wmax = ηmax·QH = 0.7013·3600 = 2525 kJ
Answer
Wmax = 2525 kJ
18.Heat engines & refrigerators
Answer: Sgen = 1.857 kJ/K
Entropy generation: over a full cycle the working fluid has no net entropy change. The hot reservoir loses QH/TH and the cold reservoir gains QL/TL. Their sum is the entropy generated, which is zero for a reversible cycle and positive for every real one.
Heat rejected
QL = QH − W = 2300 − 1219 = 1081 kJ
Absolute temperatures
TH = 900 + 273.15 = 1173 K
TL = 10 + 273.15 = 283.1 K
Entropy changes of the reservoirs
ΔSH = −2300/1173 = −1.961 kJ/K
ΔSL = 1081/283.1 = 3.818 kJ/K
Sgen = 3.818 − 1.961 = 1.857 kJ/K
Answer
Sgen = 1.857 kJ/K
Sgen > 0, so the engine is possible but irreversible.
19.Waves, sound & optics
Answer: β = 83.96 dB
Waves: a periodic wave moves one wavelength in one period, so v = fλ with T = 1/f. On a stretched string v = √(T/μ), with T the tension and μ = m/L the mass per metre. Sound in air travels at about 343 m/s at 20 °C, light in vacuum at c = 3.00 × 10⁸ m/s. Loudness is measured on a logarithmic scale: β = 10·log₁₀(I/I₀) dB with I₀ = 10⁻¹² W/m², so 10 times the intensity adds 10 dB. A point source spreads its power P over a sphere: I = P/(4πr²).
Intensity
I = P/(4πr²) = 0.0002487 W/m²
Level
β = 10·log₁₀(0.0002487/10⁻¹²) = 83.96 dB
Answer
β = 83.96 dB
20.Waves, sound & optics
Answer: θ2 = 32.14 °
Interference and diffraction: light from two slits a distance d apart reaches a point on the screen with a path difference d·sin θ. Bright fringes appear where d·sin θ = mλ (m = 0, ±1, ±2, …). For a screen at distance L ≫ d, the m-th bright fringe is at y = mλL/d and the fringe spacing is Δy = λL/d. A grating with N lines per millimetre has d = 1/N and sharp maxima at d·sin θ = mλ; since sin θ ≤ 1, the highest order is the largest whole number m ≤ d/λ. A single slit of width a has dark fringes at a·sin θ = mλ, m = ±1, ±2, …