Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A car speeding at a constant 19 m/s passes a police car standing still. At that moment the police car starts and accelerates uniformly at 5.5 m/s². How long does it take the police car to catch up? Find t.
vcar = 19 m/sapolice = 5.5 m/s²v0,police = 0
t = s
2.KinematicsHard
A tram starts from rest and accelerates at 1.5 m/s² for 9 s, then runs at constant speed for 8 s, and finally brakes at 5 m/s² until it stops. Find the total distance s between the two stops.
a1 = 1.5 m/s²t1 = 9 st2 = 8 sa3 = −5 m/s²
s = m
3.Newton’s lawsMedium
Masses of 7.5 kg and 3.5 kg hang on either side of a light, frictionless pulley, connected by a light string. The system is released from rest. Use g = 9.81 m/s². Find the acceleration a of the masses.
m1 = 7.5 kgm2 = 3.5 kgg = 9.81 m/s²
a = m/s²
4.Newton’s lawsHard
A block is given a push so that it starts sliding up a ramp at 35° with a speed of 6 m/s. The coefficient of kinetic friction is 0.15. Use g = 9.81 m/s². How far d along the ramp does it slide before it stops?
v₀ = 6 m/sθ = 35°μ = 0.15g = 9.81 m/s²
d = m
5.Projectile motionMedium
A ball is launched from level ground at 25° above the horizontal and lands 95 m away. Ignore air resistance and use g = 9.81 m/s². Find the launch speed v0.
θ = 25°R = 95 mg = 9.81 m/s²
v0 = m/s
6.Projectile motionHard
A ball is thrown from ground level at 36 m/s and 45° above the horizontal. It lands on the flat roof of a building 17 m high, on its way down. Ignore air resistance and use g = 9.81 m/s². Find the horizontal distance x from the launch point to where it lands.
v₀ = 36 m/sθ = 45°hroof = 17 mg = 9.81 m/s²
x = m
7.Work & energyMedium
A 2.5 kg block slides 12 m down a slope at 25° to the horizontal, with a coefficient of kinetic friction of 0.25. Find the work Wf done against friction.
m = 2.5 kgθ = 25°μ = 0.25d = 12 mg = 9.81 m/s²
Wf = J
8.Work & energyHard
A 2 kg block starts from rest at the bottom of a 30° slope and is pulled up the slope by a constant force of 25 N parallel to the slope. The coefficient of kinetic friction is 0.25. Find the speed v of the block after it has moved 7 m up the slope.
A 0.5 kg glider moving at 6 m/s makes a perfectly elastic head-on collision with a 4 kg glider at rest on a frictionless track. Find the velocity v′2 of the second glider after the collision.
m1 = 0.5 kgm2 = 4 kgv1 = 6 m/sv2 = 0
v′2 = m/s
10.Momentum & collisionsHard
At a crossing an 800 kg car travelling east at 22 m/s collides with a 900 kg car travelling north at 15 m/s. The cars lock together. Find the speed v′ of the wreck just after the collision.
m1 = 800 kgv1 = 22 m/s (E)m2 = 900 kgv2 = 15 m/s (N)
v′ = m/s
11.Hydrostatic forceMedium
A vertical rectangular gate 1.5 m wide sits in the wall of a tank of water, with its top edge 4 m below the surface. Find the resultant hydrostatic force F on the gate.
A vertical rectangular gate 2 m wide sits in the wall of a tank of water, with its top edge 4 m below the surface. Find the resultant hydrostatic force F on the gate.
Water flows through a horizontal pipe that narrows from 200 mm to 75 mm. In the wide section the pressure is 360 kPa and the velocity is 1.25 m/s. Ignoring losses, find the pressure p2 in the narrow section.
Water flows up through a pipe that narrows from 75 mm to 50 mm while rising 5 m. At section 1 the pressure is 330 kPa and the velocity is 1.75 m/s. Ignoring losses, find the pressure p2 at section 2.
A heat engine works between a hot reservoir at 700 °C and a cold reservoir at 35 °C. Find the highest possible thermal efficiency ηmax.
TH = 700 °CTL = 35 °C
ηmax = %
18.Heat engines & refrigeratorsHard
A Carnot heat engine receives 140 kW of heat from a source at 600 °C and rejects heat to the surroundings at 25 °C. All of its work drives a Carnot refrigerator that removes heat from a freezer at 0 °C and also rejects heat to the surroundings at 25 °C. Find the rate Q̇L at which heat is removed from the freezer.
TH = 600 °CT0 = 25 °CTL = 0 °CQ̇H = 140 kW
Q̇L = kW
19.Waves, sound & opticsMedium
Light travels in diamond (n = 2.42) towards a flat boundary with acrylic (n = 1.49). Find the critical angle θc beyond which it is totally reflected.
n1 = 2.42n2 = 1.49
θc = °
20.Waves, sound & opticsHard
An optical fibre has a core with n₁ = 1.55 and a cladding with n₂ = 1.45. Find its numerical aperture NA.
n1 = 1.55n2 = 1.45
NA =
3Solutions
1.Kinematics
Answer: t = 6.909 s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Equal distances
v·t = ½·a·t² → t = 2v/a = 2·19/5.5 = 6.909 s
Answer
t = 6.909 s
At that moment the police car moves at 2v = 38 m/s.
2.Kinematics
Answer: s = 187 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Top speed
v = a1·t1 = 1.5·9 = 13.5 m/s
Distance of each phase
s1 = ½·1.5·9² = 60.75 m
s2 = 13.5·8 = 108 m
s3 = 13.5²/(2·5) = 18.23 m
Total distance
s = 60.75 + 108 + 18.23 = 187 m
Answer
s = 187 m
3.Newton’s laws
Answer: a = 3.567 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Acceleration
The net driving force is the difference of the weights; it moves the total mass.
a = (7.5 − 3.5)·9.81/(7.5 + 3.5) = 3.567 m/s²
Answer
a = 3.567 m/s²
4.Newton’s laws
Answer: d = 2.635 m
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Deceleration
Both forces point down the slope; the mass cancels.
a = 9.81·(sin 35° + 0.15·cos 35°) = 6.832 m/s²
Distance
d = v₀²/(2a) = 6²/(2·6.832) = 2.635 m
Answer
d = 2.635 m
5.Projectile motion
Answer: v0 = 34.88 m/s
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Solve the range formula for v₀
v₀ = √(g·R/sin 2θ) = √(9.81·95/sin 50°) = 34.88 m/s
Answer
v0 = 34.88 m/s
6.Projectile motion
Answer: x = 112.1 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
vx = 25.46 m/s, vy = 25.46 m/s
Time to land on the roof
Larger root: the ball is descending.
17 = 25.46·t − 4.905·t²
t = (25.46 + √(25.46² − 2·9.81·17))/9.81 = 4.403 s
Horizontal distance
x = vx·t = 25.46·4.403 = 112.1 m
Answer
x = 112.1 m
7.Work & energy
Answer: Wf = 66.68 J
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Friction force
N = mg·cos θ = 24.53·0.9063 = 22.23 N
F = μN = 0.25·22.23 = 5.557 N
Work against friction
Wf = F·d = 5.557·12 = 66.68 J
Answer
Wf = 66.68 J
8.Work & energy
Answer: v = 8.752 m/s
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Forces along the slope
m·g = 2·9.81 = 19.62 N
mg·sin θ = 9.81 N
μ·mg·cos θ = 4.248 N
Work–energy
½mv² = (25 − 14.06)·7 = 76.6 J
v = √(2·76.6/2) = 8.752 m/s
Answer
v = 8.752 m/s
9.Momentum & collisions
Answer: v′2 = 1.333 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Elastic collision with a target at rest
Solving momentum and energy conservation together gives these two results.
v′1 = (0.5 − 4)/(0.5 + 4)·6 = −4.667 m/s
v′2 = 2·0.5/(0.5 + 4)·6 = 1.333 m/s
Answer
v′2 = 1.333 m/s
10.Momentum & collisions
Answer: v′ = 13.05 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 4 + 1/2 = 4.5 m
A = H·b = 1·1.5 = 1.5 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·4.5·1.5 = 66.22 kN
Answer
F = 66.22 kN
12.Hydrostatic force
Answer: F = 257.5 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 4 + 2.5/2 = 5.25 m
A = H·b = 2.5·2 = 5 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·5.25·5 = 257.5 kN
Answer
F = 257.5 kN
13.Continuity & Bernoulli
Answer: p2 = 321.3 kPa
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Combined gas law: for a fixed amount of ideal gas, P1V1/T1 = P2V2/T2.
Absolute temperatures
T1 = 283.1 K, T2 = 473.1 K
Combined gas law
V2 = V1·(P1/P2)·(T2/T1) = 2·(150/800)·(473.1/283.1) = 0.6266 L
Answer
V2 = 0.6266 L
17.Heat engines & refrigerators
Answer: ηmax = 68.33 %
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 700 + 273.15 = 973.1 K
TL = 35 + 273.15 = 308.1 K
Carnot efficiency
ηmax = 1 − TL/TH = 1 − 308.1/973.1 = 68.33 %
Answer
ηmax = 68.33 %
18.Heat engines & refrigerators
Answer: Q̇L = 1007 kW
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 600 + 273.15 = 873.1 K
T0 = 25 + 273.15 = 298.1 K
TL = 0 + 273.15 = 273.1 K
Engine work
η = 1 − 298.1/873.1 = 0.6585
Ẇ = 0.6585·140 = 92.19 kW
Heat removed by the refrigerator
COPR = 273.1/(298.1 − 273.1) = 10.93
Q̇L = 10.93·92.19 = 1007 kW
Answer
Q̇L = 1007 kW
19.Waves, sound & optics
Answer: θc = 38 °
Geometric optics: at a boundary, n₁·sin θ₁ = n₂·sin θ₂ (Snell's law), with angles measured from the normal and n = c/v. Going into a slower medium the ray bends towards the normal. From a denser medium (n₁ > n₂) beyond the critical angle θc = arcsin(n₂/n₁) all light is reflected: total internal reflection. Thin lenses and spherical mirrors obey 1/f = 1/do + 1/di with the magnification m = −di/do. Sign convention: f > 0 for a converging lens and a concave mirror (f = R/2), f < 0 for a diverging lens and a convex mirror; di > 0 for a real image, di < 0 for a virtual one, and m < 0 for an inverted image.
Refraction at 90°
sin θc = n₂/n₁ = 1.49/2.42 = 0.6157
Critical angle
θc = arcsin(0.6157) = 38°
Answer
θc = 38°
20.Waves, sound & optics
Answer: NA = 0.5477
Geometric optics: at a boundary, n₁·sin θ₁ = n₂·sin θ₂ (Snell's law), with angles measured from the normal and n = c/v. Going into a slower medium the ray bends towards the normal. From a denser medium (n₁ > n₂) beyond the critical angle θc = arcsin(n₂/n₁) all light is reflected: total internal reflection. Thin lenses and spherical mirrors obey 1/f = 1/do + 1/di with the magnification m = −di/do. Sign convention: f > 0 for a converging lens and a concave mirror (f = R/2), f < 0 for a diverging lens and a convex mirror; di > 0 for a real image, di < 0 for a virtual one, and m < 0 for an inverted image.