Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A car driving at 45 km/h brakes with a constant deceleration of 7 m/s² until it stops. How long does braking take? Find t.
v₀ = 45 km/ha = −7 m/s²v = 0
t = s
2.KinematicsHard
A ball is thrown straight up at 7 m/s from the edge of a roof 15 m above the ground. Ignore air resistance and use g = 9.81 m/s². Find the greatest height hmax above the ground.
v₀ = 7 m/sh₀ = 15 mg = 9.81 m/s²
hmax = m
3.Newton’s lawsMedium
A 10 kg block slides down a slope at 40° to the horizontal. The coefficient of kinetic friction is 0.3. Use g = 9.81 m/s². Find the acceleration a of the block along the slope.
m = 10 kgθ = 40°μ = 0.3g = 9.81 m/s²
a = m/s²
4.Newton’s lawsHard
A block is given a push so that it starts sliding up a ramp at 25° with a speed of 4.5 m/s. The coefficient of kinetic friction is 0.1. Use g = 9.81 m/s². How far d along the ramp does it slide before it stops?
v₀ = 4.5 m/sθ = 25°μ = 0.1g = 9.81 m/s²
d = m
5.Projectile motionMedium
A ball is launched at 40° above horizontal from level ground. Ignore air resistance. Find the maximum height H the ball reaches.
v0 = 16 m/sθ = 40°g = 9.81 m/s²
H = m
6.Projectile motionHard
A ball is thrown from ground level at 27 m/s and 65° above the horizontal. It lands on the flat roof of a building 17 m high, on its way down. Ignore air resistance and use g = 9.81 m/s². Find the horizontal distance x from the launch point to where it lands.
v₀ = 27 m/sθ = 65°hroof = 17 mg = 9.81 m/s²
x = m
7.Work & energyMedium
A 5 kg ball hangs on a light string of length 1.5 m. It is pulled aside until the string makes 50° with the vertical and released from rest. Find the tension T in the string when the ball passes the lowest point.
m = 5 kgL = 1.5 mθ = 50°g = 9.81 m/s²
T = N
8.Work & energyHard
A 10 kg cart is released from rest at a height of 5.2 m on a smooth track that leads into a vertical circular loop of radius 2 m. Find the normal force N the track exerts on the cart at the top of the loop.
m = 10 kgh = 5.2 mR = 2 mg = 9.81 m/s²
N = N
9.Momentum & collisionsMedium
A 4.5 kg glider moving at 3 m/s makes a perfectly elastic head-on collision with a 3.5 kg glider at rest on a frictionless track. Find the velocity v′1 of the first glider after the collision (positive in its original direction).
m1 = 4.5 kgm2 = 3.5 kgv1 = 3 m/sv2 = 0
v′1 = m/s
10.Momentum & collisionsHard
At a crossing a 1400 kg car travelling east at 17 m/s collides with a 1800 kg car travelling north at 17 m/s. The cars lock together. Find the direction θ of the wreck just after the collision, measured north of east.
m1 = 1400 kgv1 = 17 m/s (E)m2 = 1800 kgv2 = 17 m/s (N)
θ = °
11.Hydrostatic forceMedium
A vertical rectangular gate 2 m wide sits in the wall of a tank of water, with its top edge 0.5 m below the surface. Find the resultant hydrostatic force F on the gate.
A vertical rectangular gate 1 m wide sits in the wall of a tank of seawater, with its top edge 3 m below the surface. Find the resultant hydrostatic force F on the gate.
d = 3 mH = 2 mb = 1 mρ = 1025 kg/m³g = 9.81 m/s²
F = kN
13.Continuity & BernoulliMedium
Water flows through a horizontal pipe that narrows from 100 mm to 40 mm. In the wide section the pressure is 260 kPa and the velocity is 2.25 m/s. Ignoring losses, find the pressure p2 in the narrow section.
A fountain nozzle points straight up. Just below the nozzle the supply pipe has a diameter of 100 mm and a gauge pressure of 130 kPa. The nozzle exit diameter is 30 mm, and the height difference across the nozzle is negligible. Ignoring losses and air resistance, find the height H the jet rises above the nozzle. Use g = 9.81 m/s².
A heat engine works between a hot reservoir at 275 °C and a cold reservoir at 5 °C. It takes in 2600 kJ of heat. Find the most work Wmax it could possibly produce.
TH = 275 °CTL = 5 °CQH = 2600 kJ
Wmax = kJ
18.Heat engines & refrigeratorsHard
A heat engine takes in 3600 kJ of heat from a reservoir at 600 °C, produces 1836 kJ of work and rejects the rest to a reservoir at 40 °C, per cycle. Find the total entropy generated Sgen per cycle.
TH = 600 °CTL = 40 °CQH = 3600 kJW = 1836 kJ
Sgen = kJ/K
19.Waves, sound & opticsMedium
A source of 1000 Hz moving at 30 m/s and an observer moving at 5 m/s approach each other. The speed of sound is 343 m/s. Find the frequency f′ that the observer hears.
f = 1000 Hzv = 343 m/svs = 30 m/svo = 5 m/s
f′ = Hz
20.Waves, sound & opticsHard
Two thin lenses share an axis, 20 cm apart: lens 1 with f₁ = 8 cm and lens 2 with f₂ = −10 cm. An object stands 12 cm in front of lens 1. Find the position di2 of the final image measured from lens 2 (positive beyond lens 2, real-is-positive convention).
f1 = 8 cmf2 = −10 cms = 20 cmdo = 12 cm
di2 = cm
3Solutions
1.Kinematics
Answer: t = 1.786 s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Units
v₀ = 45/3.6 = 12.5 m/s
Braking time
0 = v₀ − a·t → t = v₀/a = 12.5/7 = 1.786 s
Answer
t = 1.786 s
2.Kinematics
Answer: hmax = 17.5 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Rise above the roof
0 = v₀² − 2·g·Δh → Δh = 7²/(2·9.81) = 2.497 m
Height above the ground
hmax = 15 + 2.497 = 17.5 m
Answer
hmax = 17.5 m
3.Newton’s laws
Answer: a = 4.051 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Deceleration
Both forces point down the slope; the mass cancels.
a = 9.81·(sin 25° + 0.1·cos 25°) = 5.035 m/s²
Distance
d = v₀²/(2a) = 4.5²/(2·5.035) = 2.011 m
Answer
d = 2.011 m
5.Projectile motion
Answer: H = 5.391 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 16·cos 40° = 12.26 m/s
vy = v0·sin θ = 16·sin 40° = 10.28 m/s
Highest point
At the top the vertical velocity is zero: vy² = 2gH.
H = vy²/(2g) = 10.28²/(2·9.81) = 5.391 m
Answer
H = 5.391 m
6.Projectile motion
Answer: x = 47.41 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
vx = 11.41 m/s, vy = 24.47 m/s
Time to land on the roof
Larger root: the ball is descending.
17 = 24.47·t − 4.905·t²
t = (24.47 + √(24.47² − 2·9.81·17))/9.81 = 4.155 s
Horizontal distance
x = vx·t = 11.41·4.155 = 47.41 m
Answer
x = 47.41 m
7.Work & energy
Answer: T = 84.09 N
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d). On a circular path the net force towards the centre must equal mv²/r.
Speed at the bottom
v² = 2gL(1 − cos θ) = 2·9.81·1.5·(1 − cos 50°) = 10.51 m²/s²
Forces at the bottom
m·g = 5·9.81 = 49.05 N
T = mg + mv²/L = 49.05 + 5·10.51/1.5 = 84.09 N
Answer
T = 84.09 N
Check: T = mg(3 − 2cos θ) = 84.09 N.
8.Work & energy
Answer: N = 19.62 N
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d). On a circular path the net force towards the centre must equal mv²/r.
Speed at the top
v² = 2g(h − 2R) = 2·9.81·(5.2 − 4) = 23.54 m²/s²
Forces at the top
m·g = 10·9.81 = 98.1 N
N = mv²/R − mg = 10·23.54/2 − 98.1 = 19.62 N
Answer
N = 19.62 N
The cart just makes it round when h = 2.5R; then N = 0 at the top.
9.Momentum & collisions
Answer: v′1 = 0.375 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Elastic collision with a target at rest
Solving momentum and energy conservation together gives these two results.
v′1 = (4.5 − 3.5)/(4.5 + 3.5)·3 = 0.375 m/s
v′2 = 2·4.5/(4.5 + 3.5)·3 = 3.375 m/s
Answer
v′1 = 0.375 m/s
10.Momentum & collisions
Answer: θ = 52.13 °
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Momentum components
px = 1400·17 = 23800 kg·m/s
py = 1800·17 = 30600 kg·m/s
Direction
tan θ = py/px = 1.286 → θ = 52.13°
Answer
θ = 52.13°
11.Hydrostatic force
Answer: F = 19.62 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 0.5 + 1/2 = 1 m
A = H·b = 1·2 = 2 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·1·2 = 19.62 kN
Answer
F = 19.62 kN
12.Hydrostatic force
Answer: F = 80.44 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 3 + 2/2 = 4 m
A = H·b = 2·1 = 2 m²
Resultant force
F = ρ·g·yc·A = 1025·9.81·4·2 = 80.44 kN
Answer
F = 80.44 kN
13.Continuity & Bernoulli
Answer: p2 = 163.7 kPa
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Exit velocity
β = 30/100 = 0.3
v2 = √(2p1/(ρ(1 − β⁴))) = √(2·130000/(1000·0.9919)) = 16.19 m/s
Height of the jet
Bernoulli along the jet: at the top the velocity is zero and the pressure is atmospheric again.
H = v2²/(2g) = 16.19²/(2·9.81) = 13.36 m
Answer
H = 13.36 m
15.Ideal gas law
Answer: P = 149.4 kPa
Ideal gas law: PV = nRT, with n = m/M.
Moles
n = m/M = 20/16.04 = 1.247 mol
T = 15 + 273.15 = 288.1 K
Pressure
P = nRT/V = 1.247·8.314·288.1/0.02 = 149.4 kPa
Answer
P = 149.4 kPa
16.Ideal gas law
Answer: ρ = 5.746 kg/m³
Ideal gas density: ρ = PM/(RT).
Rearrange the gas law
PV = (m/M)RT → ρ = m/V = PM/(RT)
T = 20 + 273.15 = 293.1 K
Density
ρ = 500·28.01/(8.314·293.1) = 5.746 kg/m³
Answer
ρ = 5.746 kg/m³
17.Heat engines & refrigerators
Answer: Wmax = 1281 kJ
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 275 + 273.15 = 548.1 K
TL = 5 + 273.15 = 278.1 K
Carnot efficiency
ηmax = 1 − TL/TH = 1 − 278.1/548.1 = 49.26 %
Maximum work
Wmax = ηmax·QH = 0.4926·2600 = 1281 kJ
Answer
Wmax = 1281 kJ
18.Heat engines & refrigerators
Answer: Sgen = 1.51 kJ/K
Entropy generation: over a full cycle the working fluid has no net entropy change. The hot reservoir loses QH/TH and the cold reservoir gains QL/TL. Their sum is the entropy generated, which is zero for a reversible cycle and positive for every real one.
Heat rejected
QL = QH − W = 3600 − 1836 = 1764 kJ
Absolute temperatures
TH = 600 + 273.15 = 873.1 K
TL = 40 + 273.15 = 313.1 K
Entropy changes of the reservoirs
ΔSH = −3600/873.1 = −4.123 kJ/K
ΔSL = 1764/313.1 = 5.633 kJ/K
Sgen = 5.633 − 4.123 = 1.51 kJ/K
Answer
Sgen = 1.51 kJ/K
Sgen > 0, so the engine is possible but irreversible.
19.Waves, sound & optics
Answer: f′ = 1112 Hz
Standing waves and the Doppler effect: a string fixed at both ends, or a pipe open at both ends, fits whole half-wavelengths: L = nλ/2, fn = n·v/(2L), n = 1, 2, 3, … A pipe closed at one end has a node at the closed end and an antinode at the open end: L = nλ/4 with odd n only, fn = n·v/(4L). When source or observer move along the line between them, f′ = f·(v ± vo)/(v ∓ vs): use the upper signs for motion towards each other. Two waves of nearly equal frequency beat at |f₁ − f₂|.
Geometric optics: at a boundary, n₁·sin θ₁ = n₂·sin θ₂ (Snell's law), with angles measured from the normal and n = c/v. Going into a slower medium the ray bends towards the normal. From a denser medium (n₁ > n₂) beyond the critical angle θc = arcsin(n₂/n₁) all light is reflected: total internal reflection. Thin lenses and spherical mirrors obey 1/f = 1/do + 1/di with the magnification m = −di/do. Sign convention: f > 0 for a converging lens and a concave mirror (f = R/2), f < 0 for a diverging lens and a convex mirror; di > 0 for a real image, di < 0 for a virtual one, and m < 0 for an inverted image.