Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A car speeding at a constant 24 m/s passes a police car standing still. At that moment the police car starts and accelerates uniformly at 2 m/s². How far from its starting point does the police car catch up? Find d.
vcar = 24 m/sapolice = 2 m/s²v0,police = 0
d = m
2.KinematicsHard
A ball is thrown straight up at 18 m/s from the edge of a roof 40 m above the ground. Ignore air resistance and use g = 9.81 m/s². How long after the throw does it hit the ground? Find t.
v₀ = 18 m/sh₀ = 40 mg = 9.81 m/s²
t = s
3.Newton’s lawsMedium
A 10 kg sled is pulled across level snow by a rope at 30° above the horizontal with a force of 80 N. The coefficient of kinetic friction is 0.2. Use g = 9.81 m/s². Find the acceleration a of the sled.
m = 10 kgF = 80 Nθ = 30°μ = 0.2g = 9.81 m/s²
a = m/s²
4.Newton’s lawsHard
A block is given a push so that it starts sliding up a ramp at 20° with a speed of 7 m/s. The coefficient of kinetic friction is 0.15. Use g = 9.81 m/s². How far d along the ramp does it slide before it stops?
v₀ = 7 m/sθ = 20°μ = 0.15g = 9.81 m/s²
d = m
5.Projectile motionMedium
A ball is launched at 20° above horizontal from level ground. Ignore air resistance. Find the maximum height H the ball reaches.
v0 = 28 m/sθ = 20°g = 9.81 m/s²
H = m
6.Projectile motionHard
A ball is launched at 13 m/s and 50° above the horizontal from the top of a 35 m cliff. Ignore air resistance and use g = 9.81 m/s². Find the speed v with which it hits the ground.
v₀ = 13 m/sθ = 50°h = 35 mg = 9.81 m/s²
v = m/s
7.Work & energyMedium
A toy launcher has a vertical spring of stiffness 800 N/m. A 0.1 kg ball is placed on it and the spring is compressed by 4 cm, then released. Ignoring air resistance and the spring’s mass, find the height h the ball rises, measured from its position when the spring was compressed.
m = 0.1 kgk = 800 N/mx = 4 cmg = 9.81 m/s²
h = m
8.Work & energyHard
A 10 kg block rests on a rough horizontal table (μ = 0.2). A light string runs from it over a smooth pulley at the edge of the table to a hanging 6 kg block. The system is released from rest. Find the speed v of the blocks after the hanging block has dropped 1 m.
m1 = 10 kgm2 = 6 kgμ = 0.2d = 1 mg = 9.81 m/s²
v = m/s
9.Momentum & collisionsMedium
A 3 kg glider moving at 3 m/s makes a perfectly elastic head-on collision with a 1 kg glider at rest on a frictionless track. Find the velocity v′1 of the first glider after the collision (positive in its original direction).
m1 = 3 kgm2 = 1 kgv1 = 3 m/sv2 = 0
v′1 = m/s
10.Momentum & collisionsHard
At a crossing a 1500 kg car travelling east at 17 m/s collides with a 1100 kg car travelling north at 24 m/s. The cars lock together. Find the direction θ of the wreck just after the collision, measured north of east.
m1 = 1500 kgv1 = 17 m/s (E)m2 = 1100 kgv2 = 24 m/s (N)
θ = °
11.Hydrostatic forceMedium
A vertical rectangular gate 1 m wide sits in the wall of a tank of water, with its top edge 1 m below the surface. Find the resultant hydrostatic force F on the gate.
A vertical rectangular gate 1.5 m wide sits in the wall of a tank of seawater, with its top edge 0.5 m below the surface. Find the depth ycp of the centre of pressure below the surface.
Water drains from a large open tank through a sharp-edged orifice with a diameter of 30 mm. The water level is kept 3.5 m above the orifice and the discharge coefficient is 0.63. Find the flow rate Q. Use g = 9.81 m/s².
d = 30 mmh = 3.5 mCd = 0.63g = 9.81 m/s²
Q = L/s
14.Continuity & BernoulliHard
A fountain nozzle points straight up. Just below the nozzle the supply pipe has a diameter of 100 mm and a gauge pressure of 30 kPa. The nozzle exit diameter is 30 mm, and the height difference across the nozzle is negligible. Ignoring losses and air resistance, find the height H the jet rises above the nozzle. Use g = 9.81 m/s².
A heat engine works between a hot reservoir at 250 °C and a cold reservoir at 30 °C. It takes in 3600 kJ of heat. Find the most work Wmax it could possibly produce.
TH = 250 °CTL = 30 °CQH = 3600 kJ
Wmax = kJ
18.Heat engines & refrigeratorsHard
A refrigerator keeps its cold space at -25 °C in a kitchen at 28 °C, removing heat from the cold space at 4 kW. Find the minimum power input Ẇmin.
TH = 28 °CTL = -25 °CQ̇L = 4 kW
Ẇmin = kW
19.Waves, sound & opticsMedium
An object stands 20 cm in front of a thin converging lens with a focal length of 12 cm. Find the image distance di. Use the sign convention 1/f = 1/do + 1/di (f < 0 for a diverging lens, di < 0 for a virtual image).
do = 20 cmf = 12 cm
di = cm
20.Waves, sound & opticsHard
Two thin lenses share an axis, 10 cm apart: lens 1 with f₁ = 12 cm and lens 2 with f₂ = 20 cm. An object stands 15 cm in front of lens 1. Find the position di2 of the final image measured from lens 2 (positive beyond lens 2, real-is-positive convention).
f1 = 12 cmf2 = 20 cms = 10 cmdo = 15 cm
di2 = cm
3Solutions
1.Kinematics
Answer: d = 576 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Equal distances
v·t = ½·a·t² → t = 2v/a = 2·24/2 = 24 s
Distance
d = v·t = 24·24 = 576 m
Answer
d = 576 m
At that moment the police car moves at 2v = 48 m/s.
2.Kinematics
Answer: t = 5.229 s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Equation of motion
Up is positive and the ground is h₀ below the starting point.
−40 = 18·t − ½·9.81·t²
4.905·t² − 18·t − 40 = 0
Solve the quadratic
Only the positive root is physical.
t = (18 + √(18² + 2·9.81·40))/9.81 = 5.229 s
Answer
t = 5.229 s
3.Newton’s laws
Answer: a = 5.766 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Normal force
N = m·g − F·sin θ = 98.1 − 80·sin 30° = 58.1 N
Horizontal forces
m·a = F·cos θ − μ·N = 69.28 − 11.62
a = 57.66/10 = 5.766 m/s²
Answer
a = 5.766 m/s²
4.Newton’s laws
Answer: d = 5.171 m
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Deceleration
Both forces point down the slope; the mass cancels.
a = 9.81·(sin 20° + 0.15·cos 20°) = 4.738 m/s²
Distance
d = v₀²/(2a) = 7²/(2·4.738) = 5.171 m
Answer
d = 5.171 m
5.Projectile motion
Answer: H = 4.674 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 28·cos 20° = 26.31 m/s
vy = v0·sin θ = 28·sin 20° = 9.577 m/s
Highest point
At the top the vertical velocity is zero: vy² = 2gH.
H = vy²/(2g) = 9.577²/(2·9.81) = 4.674 m
Answer
H = 4.674 m
6.Projectile motion
Answer: v = 29.25 m/s
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
vx = 13·cos 50° = 8.356 m/s
vy0 = 13·sin 50° = 9.959 m/s
Vertical speed at impact
Energy or v² = v₀² + 2as in the vertical direction.
vy = √(9.959² + 2·9.81·35) = 28.03 m/s
Impact speed
v = √(8.356² + 28.03²) = 29.25 m/s
Answer
v = 29.25 m/s
Check with energy: v² = v₀² + 2gh.
7.Work & energy
Answer: h = 0.6524 m
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Spring energy
x = 4 cm = 0.04 m
½kx² = ½·800·0.04² = 0.64 J
Height
m·g = 0.1·9.81 = 0.981 N
h = ½kx²/(mg) = 0.64/0.981 = 0.6524 m
Answer
h = 0.6524 m
8.Work & energy
Answer: v = 2.215 m/s
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy released and lost
m₂g·d = 58.86·1 = 58.86 J
μ·m₁g·d = 0.2·98.1·1 = 19.62 J
Kinetic energy of both blocks
½(m₁ + m₂)v² = 39.24 → v = √(2·39.24/16) = 2.215 m/s
Answer
v = 2.215 m/s
9.Momentum & collisions
Answer: v′1 = 1.5 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Elastic collision with a target at rest
Solving momentum and energy conservation together gives these two results.
v′1 = (3 − 1)/(3 + 1)·3 = 1.5 m/s
v′2 = 2·3/(3 + 1)·3 = 4.5 m/s
Answer
v′1 = 1.5 m/s
10.Momentum & collisions
Answer: θ = 45.99 °
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Momentum components
px = 1500·17 = 25500 kg·m/s
py = 1100·24 = 26400 kg·m/s
Direction
tan θ = py/px = 1.035 → θ = 45.99°
Answer
θ = 45.99°
11.Hydrostatic force
Answer: F = 25.75 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 1 + 1.5/2 = 1.75 m
A = H·b = 1.5·1 = 1.5 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·1.75·1.5 = 25.75 kN
Answer
F = 25.75 kN
12.Hydrostatic force
Answer: ycp = 1.4 m
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 0.5 + 1.5/2 = 1.25 m
A = H·b = 1.5·1.5 = 2.25 m²
Resultant force
F = ρ·g·yc·A = 1025·9.81·1.25·2.25 = 28.28 kN
Centre of pressure
Pressure grows with depth, so the resultant acts below the centroid.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Ideal jet velocity
√(2gh) = √(2·9.81·3.5) = 8.287 m/s
Actual flow rate
The discharge coefficient accounts for the contraction of the jet and friction at the edge.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Exit velocity
β = 30/100 = 0.3
v2 = √(2p1/(ρ(1 − β⁴))) = √(2·30000/(1000·0.9919)) = 7.778 m/s
Height of the jet
Bernoulli along the jet: at the top the velocity is zero and the pressure is atmospheric again.
H = v2²/(2g) = 7.778²/(2·9.81) = 3.083 m
Answer
H = 3.083 m
15.Ideal gas law
Answer: V = 1311 L
Ideal gas law: PV = nRT, with n = m/M.
Moles
n = 280/4.003 = 69.95 mol
T = 65 + 273.15 = 338.1 K
Volume
V = nRT/P = 69.95·8.314·338.1/150 = 1311 L
Answer
V = 1311 L
16.Ideal gas law
Answer: ρ = 4.089 kg/m³
Ideal gas density: ρ = PM/(RT).
Rearrange the gas law
PV = (m/M)RT → ρ = m/V = PM/(RT)
T = 180 + 273.15 = 453.1 K
Density
ρ = 350·44.01/(8.314·453.1) = 4.089 kg/m³
Answer
ρ = 4.089 kg/m³
17.Heat engines & refrigerators
Answer: Wmax = 1514 kJ
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 250 + 273.15 = 523.1 K
TL = 30 + 273.15 = 303.1 K
Carnot efficiency
ηmax = 1 − TL/TH = 1 − 303.1/523.1 = 42.05 %
Maximum work
Wmax = ηmax·QH = 0.4205·3600 = 1514 kJ
Answer
Wmax = 1514 kJ
18.Heat engines & refrigerators
Answer: Ẇmin = 0.8543 kW
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
The least work is needed by a reversible machine, which has the highest COP.
Ẇmin = Q̇L/COP = 4/4.682 = 0.8543 kW
Answer
Ẇmin = 0.8543 kW
19.Waves, sound & optics
Answer: di = 30 cm
Geometric optics: at a boundary, n₁·sin θ₁ = n₂·sin θ₂ (Snell's law), with angles measured from the normal and n = c/v. Going into a slower medium the ray bends towards the normal. From a denser medium (n₁ > n₂) beyond the critical angle θc = arcsin(n₂/n₁) all light is reflected: total internal reflection. Thin lenses and spherical mirrors obey 1/f = 1/do + 1/di with the magnification m = −di/do. Sign convention: f > 0 for a converging lens and a concave mirror (f = R/2), f < 0 for a diverging lens and a convex mirror; di > 0 for a real image, di < 0 for a virtual one, and m < 0 for an inverted image.
Thin-lens equation
1/di = 1/f − 1/do = 1/12 − 1/20
di = 30 cm
Ray diagram
real, on the far side of the lens
Answer
di = 30 cm
20.Waves, sound & optics
Answer: di2 = 14.29 cm
Geometric optics: at a boundary, n₁·sin θ₁ = n₂·sin θ₂ (Snell's law), with angles measured from the normal and n = c/v. Going into a slower medium the ray bends towards the normal. From a denser medium (n₁ > n₂) beyond the critical angle θc = arcsin(n₂/n₁) all light is reflected: total internal reflection. Thin lenses and spherical mirrors obey 1/f = 1/do + 1/di with the magnification m = −di/do. Sign convention: f > 0 for a converging lens and a concave mirror (f = R/2), f < 0 for a diverging lens and a convex mirror; di > 0 for a real image, di < 0 for a virtual one, and m < 0 for an inverted image.