Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A plane needs a speed of 240 km/h to take off and the usable runway is 1200 m long. Starting from rest, what constant acceleration a does it need?
v₀ = 0v = 240 km/hs = 1200 m
a = m/s²
2.KinematicsHard
A stone is dropped from rest into a well. The splash is heard 3.6 s after the stone is released. The speed of sound is 343 m/s; ignore air resistance and use g = 9.81 m/s². Find the depth d of the well.
ttotal = 3.6 svsound = 343 m/sg = 9.81 m/s²
d = m
3.Newton’s lawsMedium
A 17 kg block slides down a slope at 45° to the horizontal. The coefficient of kinetic friction is 0.2. Use g = 9.81 m/s². Find the acceleration a of the block along the slope.
m = 17 kgθ = 45°μ = 0.2g = 9.81 m/s²
a = m/s²
4.Newton’s lawsHard
Two blocks on a level floor are joined by a light horizontal string. A horizontal force of 100 N pulls the front 3 kg block; the 4 kg block is towed behind. The coefficient of kinetic friction is 0.2 for both blocks. Use g = 9.81 m/s². Find the acceleration a of the blocks.
m1 = 4 kgm2 = 3 kgF = 100 Nμ = 0.2g = 9.81 m/s²
a = m/s²
5.Projectile motionMedium
A ball is launched at 35° above horizontal from level ground. Ignore air resistance. Find the maximum height H the ball reaches.
v0 = 40 m/sθ = 35°g = 9.81 m/s²
H = m
6.Projectile motionHard
A ball is launched at 35 m/s and 60° above the horizontal from the top of a 60 m cliff. Ignore air resistance and use g = 9.81 m/s². Find the greatest height H above the ground at the foot of the cliff.
v₀ = 35 m/sθ = 60°h = 60 mg = 9.81 m/s²
H = m
7.Work & energyMedium
A 2 kg ball hangs on a light string of length 0.8 m. It is pulled aside until the string makes 20° with the vertical and released from rest. Find the tension T in the string when the ball passes the lowest point.
m = 2 kgL = 0.8 mθ = 20°g = 9.81 m/s²
T = N
8.Work & energyHard
A 4 kg block is released from rest at height 4 m on a smooth ramp. At the bottom it crosses a rough horizontal strip 4 m long (μ = 0.1) and then runs onto a spring (k = 4000 N/m) on a smooth surface. Find the maximum compression x of the spring.
m = 4 kgh = 4 mL = 4 mμ = 0.1k = 4000 N/mg = 9.81 m/s²
x = cm
9.Momentum & collisionsMedium
A 5 kg glider moving at 9 m/s makes a perfectly elastic head-on collision with a 4.5 kg glider at rest on a frictionless track. Find the velocity v′2 of the second glider after the collision.
m1 = 5 kgm2 = 4.5 kgv1 = 9 m/sv2 = 0
v′2 = m/s
10.Momentum & collisionsHard
At a crossing a 1900 kg car travelling east at 25 m/s collides with a 1300 kg car travelling north at 15 m/s. The cars lock together. Find the speed v′ of the wreck just after the collision.
m1 = 1900 kgv1 = 25 m/s (E)m2 = 1300 kgv2 = 15 m/s (N)
v′ = m/s
11.Hydrostatic forceMedium
A vertical rectangular gate 3 m wide sits in the wall of a tank of water, with its top edge 0.5 m below the surface. Find the resultant hydrostatic force F on the gate.
A vertical rectangular gate 3 m wide sits in the wall of a tank of oil, with its top edge 0.5 m below the surface. Find the resultant hydrostatic force F on the gate.
d = 0.5 mH = 3 mb = 3 mρ = 880 kg/m³g = 9.81 m/s²
F = kN
13.Continuity & BernoulliMedium
Water drains from a large open tank through a sharp-edged orifice with a diameter of 40 mm. The water level is kept 1.5 m above the orifice and the discharge coefficient is 0.61. Find the flow rate Q. Use g = 9.81 m/s².
d = 40 mmh = 1.5 mCd = 0.61g = 9.81 m/s²
Q = L/s
14.Continuity & BernoulliHard
A fountain nozzle points straight up. Just below the nozzle the supply pipe has a diameter of 75 mm and a gauge pressure of 30 kPa. The nozzle exit diameter is 40 mm, and the height difference across the nozzle is negligible. Ignoring losses and air resistance, find the height H the jet rises above the nozzle. Use g = 9.81 m/s².
A reversible refrigerator keeps a cold room at 2 °C by removing 8.5 kW of heat, and rejects heat to the surroundings at 25 °C. Find the rate Q̇H at which it rejects heat.
TL = 2 °CTH = 25 °CQ̇L = 8.5 kW
Q̇H = kW
18.Heat engines & refrigeratorsHard
A heat engine takes in 4800 kJ of heat from a reservoir at 700 °C, produces 1680 kJ of work and rejects the rest to a reservoir at 25 °C, per cycle. Find the total entropy generated Sgen per cycle.
TH = 700 °CTL = 25 °CQH = 4800 kJW = 1680 kJ
Sgen = kJ/K
19.Waves, sound & opticsMedium
An object stands 6 cm in front of a thin converging lens with a focal length of 12 cm. Find the image distance di. Use the sign convention 1/f = 1/do + 1/di (f < 0 for a diverging lens, di < 0 for a virtual image).
do = 6 cmf = 12 cm
di = cm
20.Waves, sound & opticsHard
A parking sensor at rest sends ultrasound of 20 kHz towards a car that approaches at 15 m/s. Find the frequency f″ of the echo received back at the sensor (speed of sound 343 m/s).
f = 20 kHzu = 15 m/sv = 343 m/s
f″ = Hz
3Solutions
1.Kinematics
Answer: a = 1.852 m/s²
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Units
v = 240/3.6 = 66.67 m/s
Acceleration
a = v²/(2s) = 66.67²/(2·1200) = 1.852 m/s²
Answer
a = 1.852 m/s²
2.Kinematics
Answer: d = 57.76 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Two parts of the time
½·9.81·t₁² = 343·(3.6 − t₁)
4.905·t₁² + 343·t₁ − 1235 = 0
Fall time
Only the positive root is physical.
t₁ = (−343 + √(343² + 4·4.905·1235))/(2·4.905) = 3.432 s
Depth
d = ½·9.81·3.432² = 57.76 m
Answer
d = 57.76 m
3.Newton’s laws
Answer: a = 5.549 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 40·cos 35° = 32.77 m/s
vy = v0·sin θ = 40·sin 35° = 22.94 m/s
Highest point
At the top the vertical velocity is zero: vy² = 2gH.
H = vy²/(2g) = 22.94²/(2·9.81) = 26.83 m
Answer
H = 26.83 m
6.Projectile motion
Answer: H = 106.8 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Vertical launch speed
vy = 35·sin 60° = 30.31 m/s
Rise above the cliff
Δh = vy²/(2g) = 30.31²/(2·9.81) = 46.83 m
Height above the ground
H = 60 + 46.83 = 106.8 m
Answer
H = 106.8 m
7.Work & energy
Answer: T = 21.99 N
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d). On a circular path the net force towards the centre must equal mv²/r.
Speed at the bottom
v² = 2gL(1 − cos θ) = 2·9.81·0.8·(1 − cos 20°) = 0.9466 m²/s²
Forces at the bottom
m·g = 2·9.81 = 19.62 N
T = mg + mv²/L = 19.62 + 2·0.9466/0.8 = 21.99 N
Answer
T = 21.99 N
Check: T = mg(3 − 2cos θ) = 21.99 N.
8.Work & energy
Answer: x = 26.58 cm
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy left after the rough strip
The ramp is smooth, so only the strip removes energy.
mgh − μmgL = 39.24·(4 − 0.1·4) = 141.3 J
Maximum compression
½kx² = 141.3 → x = √(2·141.3/4000) = 0.2658 m = 26.58 cm
Answer
x = 26.58 cm
9.Momentum & collisions
Answer: v′2 = 9.474 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Elastic collision with a target at rest
Solving momentum and energy conservation together gives these two results.
v′1 = (5 − 4.5)/(5 + 4.5)·9 = 0.4737 m/s
v′2 = 2·5/(5 + 4.5)·9 = 9.474 m/s
Answer
v′2 = 9.474 m/s
10.Momentum & collisions
Answer: v′ = 16.05 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 0.5 + 2/2 = 1.5 m
A = H·b = 2·3 = 6 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·1.5·6 = 88.29 kN
Answer
F = 88.29 kN
12.Hydrostatic force
Answer: F = 155.4 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 0.5 + 3/2 = 2 m
A = H·b = 3·3 = 9 m²
Resultant force
F = ρ·g·yc·A = 880·9.81·2·9 = 155.4 kN
Answer
F = 155.4 kN
13.Continuity & Bernoulli
Answer: Q = 4.158 L/s
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Ideal jet velocity
√(2gh) = √(2·9.81·1.5) = 5.425 m/s
Actual flow rate
The discharge coefficient accounts for the contraction of the jet and friction at the edge.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Exit velocity
β = 40/75 = 0.5333
v2 = √(2p1/(ρ(1 − β⁴))) = √(2·30000/(1000·0.9191)) = 8.08 m/s
Height of the jet
Bernoulli along the jet: at the top the velocity is zero and the pressure is atmospheric again.
H = v2²/(2g) = 8.08²/(2·9.81) = 3.327 m
Answer
H = 3.327 m
15.Ideal gas law
Answer: V = 276.9 L
Ideal gas law: PV = nRT, with n = m/M.
Moles
n = 420/28.01 = 14.99 mol
T = 60 + 273.15 = 333.1 K
Volume
V = nRT/P = 14.99·8.314·333.1/150 = 276.9 L
Answer
V = 276.9 L
16.Ideal gas law
Answer: ρ = 6.985 kg/m³
Ideal gas density: ρ = PM/(RT).
Rearrange the gas law
PV = (m/M)RT → ρ = m/V = PM/(RT)
T = 30 + 273.15 = 303.1 K
Density
ρ = 400·44.01/(8.314·303.1) = 6.985 kg/m³
Answer
ρ = 6.985 kg/m³
17.Heat engines & refrigerators
Answer: Q̇H = 9.211 kW
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 25 + 273.15 = 298.1 K
TL = 2 + 273.15 = 275.1 K
Reversible heat ratio
Q̇H = Q̇L·TH/TL = 8.5·298.1/275.1 = 9.211 kW
Answer
Q̇H = 9.211 kW
Power input: Ẇ = 0.7105 kW.
18.Heat engines & refrigerators
Answer: Sgen = 5.532 kJ/K
Entropy generation: over a full cycle the working fluid has no net entropy change. The hot reservoir loses QH/TH and the cold reservoir gains QL/TL. Their sum is the entropy generated, which is zero for a reversible cycle and positive for every real one.
Heat rejected
QL = QH − W = 4800 − 1680 = 3120 kJ
Absolute temperatures
TH = 700 + 273.15 = 973.1 K
TL = 25 + 273.15 = 298.1 K
Entropy changes of the reservoirs
ΔSH = −4800/973.1 = −4.932 kJ/K
ΔSL = 3120/298.1 = 10.46 kJ/K
Sgen = 10.46 − 4.932 = 5.532 kJ/K
Answer
Sgen = 5.532 kJ/K
Sgen > 0, so the engine is possible but irreversible.
19.Waves, sound & optics
Answer: di = −12 cm
Geometric optics: at a boundary, n₁·sin θ₁ = n₂·sin θ₂ (Snell's law), with angles measured from the normal and n = c/v. Going into a slower medium the ray bends towards the normal. From a denser medium (n₁ > n₂) beyond the critical angle θc = arcsin(n₂/n₁) all light is reflected: total internal reflection. Thin lenses and spherical mirrors obey 1/f = 1/do + 1/di with the magnification m = −di/do. Sign convention: f > 0 for a converging lens and a concave mirror (f = R/2), f < 0 for a diverging lens and a convex mirror; di > 0 for a real image, di < 0 for a virtual one, and m < 0 for an inverted image.
Thin-lens equation
1/di = 1/f − 1/do = 1/12 − 1/6
di = −12 cm
Ray diagram
virtual, on the same side as the object
Answer
di = −12 cm
20.Waves, sound & optics
Answer: f″ = 21829 Hz
Standing waves and the Doppler effect: a string fixed at both ends, or a pipe open at both ends, fits whole half-wavelengths: L = nλ/2, fn = n·v/(2L), n = 1, 2, 3, … A pipe closed at one end has a node at the closed end and an antinode at the open end: L = nλ/4 with odd n only, fn = n·v/(4L). When source or observer move along the line between them, f′ = f·(v ± vo)/(v ∓ vs): use the upper signs for motion towards each other. Two waves of nearly equal frequency beat at |f₁ − f₂|.