Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A car driving at 90 km/h brakes with a constant deceleration of 6 m/s² until it stops. Find the braking distance s.
v₀ = 90 km/ha = −6 m/s²v = 0
s = m
2.KinematicsHard
A ball is thrown straight up at 9 m/s from the edge of a roof 25 m above the ground. Ignore air resistance and use g = 9.81 m/s². Find the greatest height hmax above the ground.
v₀ = 9 m/sh₀ = 25 mg = 9.81 m/s²
hmax = m
3.Newton’s lawsMedium
A 10 kg block slides down a slope at 30° to the horizontal. The coefficient of kinetic friction is 0.15. Use g = 9.81 m/s². Find the acceleration a of the block along the slope.
m = 10 kgθ = 30°μ = 0.15g = 9.81 m/s²
a = m/s²
4.Newton’s lawsHard
A 2 kg block on a horizontal table is connected by a light string over a frictionless pulley to a hanging 2 kg mass. The coefficient of kinetic friction between block and table is 0.3. Use g = 9.81 m/s². Find the tension T in the string.
m1 = 2 kgm2 = 2 kgμ = 0.3g = 9.81 m/s²
T = N
5.Projectile motionMedium
A ball is kicked from level ground at 40 m/s and 55° above the horizontal towards a wall 46 m away. Ignore air resistance and use g = 9.81 m/s². At what height y does the ball pass the wall?
v₀ = 40 m/sθ = 55°x = 46 mg = 9.81 m/s²
y = m
6.Projectile motionHard
A ball is launched at 15 m/s and 30° above the horizontal from the top of a 60 m cliff. Ignore air resistance and use g = 9.81 m/s². Find the greatest height H above the ground at the foot of the cliff.
v₀ = 15 m/sθ = 30°h = 60 mg = 9.81 m/s²
H = m
7.Work & energyMedium
A toy launcher has a vertical spring of stiffness 2000 N/m. A 0.15 kg ball is placed on it and the spring is compressed by 3 cm, then released. Ignoring air resistance and the spring’s mass, find the height h the ball rises, measured from its position when the spring was compressed.
m = 0.15 kgk = 2000 N/mx = 3 cmg = 9.81 m/s²
h = m
8.Work & energyHard
A 5 kg cart is released from rest at a height of 14 m on a smooth track that leads into a vertical circular loop of radius 4 m. Find the speed v of the cart at the top of the loop.
m = 5 kgh = 14 mR = 4 mg = 9.81 m/s²
v = m/s
9.Momentum & collisionsMedium
An 8 g bullet is fired horizontally into a 5 kg wooden block hanging on light strings, and stays inside it. The block swings up until it is 17 cm higher than at the start. Use g = 9.81 m/s². Find the speed v of the bullet before impact.
m = 8 gM = 5 kgh = 17 cmg = 9.81 m/s²
v = m/s
10.Momentum & collisionsHard
A 0.3 kg ball hits a wall at 17 m/s and bounces straight back at 5 m/s. The contact lasts 5 ms. Find the average force Favg of the wall on the ball.
m = 0.3 kgvin = 17 m/svout = 5 m/sΔt = 5 ms
Favg = N
11.Hydrostatic forceMedium
A vertical rectangular gate 3 m wide sits in the wall of a tank of water, with its top edge 1.5 m below the surface. Find the resultant hydrostatic force F on the gate.
A vertical rectangular gate 3 m wide sits in the wall of a tank of water, with its top edge 2 m below the surface. Find the resultant hydrostatic force F on the gate.
Water flows through a horizontal pipe that narrows from 75 mm to 50 mm. In the wide section the pressure is 180 kPa and the velocity is 1.75 m/s. Ignoring losses, find the pressure p2 in the narrow section.
A fountain nozzle points straight up. Just below the nozzle the supply pipe has a diameter of 100 mm and a gauge pressure of 140 kPa. The nozzle exit diameter is 40 mm, and the height difference across the nozzle is negligible. Ignoring losses and air resistance, find the height H the jet rises above the nozzle. Use g = 9.81 m/s².
A heat engine works between a hot reservoir at 775 °C and a cold reservoir at 10 °C. Find the highest possible thermal efficiency ηmax.
TH = 775 °CTL = 10 °C
ηmax = %
18.Heat engines & refrigeratorsHard
A refrigerator keeps its cold space at 4 °C in a kitchen at 28 °C, removing heat from the cold space at 1.5 kW. Find the highest possible coefficient of performance COPmax.
TH = 28 °CTL = 4 °CQ̇L = 1.5 kW
COPmax =
19.Waves, sound & opticsMedium
A source of 400 Hz moving at 25 m/s and an observer moving at 20 m/s approach each other. The speed of sound is 343 m/s. Find the frequency f′ that the observer hears.
f = 400 Hzv = 343 m/svs = 25 m/svo = 20 m/s
f′ = Hz
20.Waves, sound & opticsHard
Two thin lenses share an axis, 15 cm apart: lens 1 with f₁ = 12 cm and lens 2 with f₂ = 15 cm. An object stands 40 cm in front of lens 1. Find the position di2 of the final image measured from lens 2 (positive beyond lens 2, real-is-positive convention).
f1 = 12 cmf2 = 15 cms = 15 cmdo = 40 cm
di2 = cm
3Solutions
1.Kinematics
Answer: s = 52.08 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Units
v₀ = 90/3.6 = 25 m/s
Braking distance
0 = v₀² − 2·a·s → s = v₀²/(2a) = 25²/(2·6) = 52.08 m
Answer
s = 52.08 m
2.Kinematics
Answer: hmax = 29.13 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Rise above the roof
0 = v₀² − 2·g·Δh → Δh = 9²/(2·9.81) = 4.128 m
Height above the ground
hmax = 25 + 4.128 = 29.13 m
Answer
hmax = 29.13 m
3.Newton’s laws
Answer: a = 3.631 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Time to the wall
vx = 40·cos 55° = 22.94 m/s
t = x/vx = 46/22.94 = 2.005 s
Height at that time
y = 32.77·2.005 − ½·9.81·2.005² = 45.98 m
Answer
y = 45.98 m
The ball is still rising at the wall.
6.Projectile motion
Answer: H = 62.87 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Vertical launch speed
vy = 15·sin 30° = 7.5 m/s
Rise above the cliff
Δh = vy²/(2g) = 7.5²/(2·9.81) = 2.867 m
Height above the ground
H = 60 + 2.867 = 62.87 m
Answer
H = 62.87 m
7.Work & energy
Answer: h = 0.6116 m
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Spring energy
x = 3 cm = 0.03 m
½kx² = ½·2000·0.03² = 0.9 J
Height
m·g = 0.15·9.81 = 1.472 N
h = ½kx²/(mg) = 0.9/1.472 = 0.6116 m
Answer
h = 0.6116 m
8.Work & energy
Answer: v = 10.85 m/s
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d). On a circular path the net force towards the centre must equal mv²/r.
Speed at the top
v² = 2g(h − 2R) = 2·9.81·(14 − 8) = 117.7 m²/s²
v = 10.85 m/s
Answer
v = 10.85 m/s
The cart just makes it round when h = 2.5R; then N = 0 at the top.
9.Momentum & collisions
Answer: v = 1143 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Swing after impact
V = √(2·g·h) = √(2·9.81·0.17) = 1.826 m/s
Collision
m·v = (m + M)·V → v = (0.008 + 5)·1.826/0.008 = 1143 m/s
Answer
v = 1143 m/s
10.Momentum & collisions
Answer: Favg = 1320 N
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Change in momentum
J = m·Δv = 0.3·(5 + 17) = 6.6 N·s
Average force
Favg = J/Δt = 6.6/0.005 = 1320 N
Answer
Favg = 1320 N
11.Hydrostatic force
Answer: F = 202.3 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 1.5 + 2.5/2 = 2.75 m
A = H·b = 2.5·3 = 7.5 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·2.75·7.5 = 202.3 kN
Answer
F = 202.3 kN
12.Hydrostatic force
Answer: F = 121.4 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 2 + 1.5/2 = 2.75 m
A = H·b = 1.5·3 = 4.5 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·2.75·4.5 = 121.4 kN
Answer
F = 121.4 kN
13.Continuity & Bernoulli
Answer: p2 = 173.8 kPa
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Exit velocity
β = 40/100 = 0.4
v2 = √(2p1/(ρ(1 − β⁴))) = √(2·140000/(1000·0.9744)) = 16.95 m/s
Height of the jet
Bernoulli along the jet: at the top the velocity is zero and the pressure is atmospheric again.
H = v2²/(2g) = 16.95²/(2·9.81) = 14.65 m
Answer
H = 14.65 m
15.Ideal gas law
Answer: V = 433.7 L
Ideal gas law: PV = nRT, with n = m/M.
Moles
n = 310/4.003 = 77.44 mol
T = 30 + 273.15 = 303.1 K
Volume
V = nRT/P = 77.44·8.314·303.1/450 = 433.7 L
Answer
V = 433.7 L
16.Ideal gas law
Answer: ρ = 3.563 kg/m³
Ideal gas density: ρ = PM/(RT).
Rearrange the gas law
PV = (m/M)RT → ρ = m/V = PM/(RT)
T = 160 + 273.15 = 433.1 K
Density
ρ = 800·16.04/(8.314·433.1) = 3.563 kg/m³
Answer
ρ = 3.563 kg/m³
17.Heat engines & refrigerators
Answer: ηmax = 72.99 %
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 775 + 273.15 = 1048 K
TL = 10 + 273.15 = 283.1 K
Carnot efficiency
ηmax = 1 − TL/TH = 1 − 283.1/1048 = 72.99 %
Answer
ηmax = 72.99 %
18.Heat engines & refrigerators
Answer: COPmax = 11.55
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Standing waves and the Doppler effect: a string fixed at both ends, or a pipe open at both ends, fits whole half-wavelengths: L = nλ/2, fn = n·v/(2L), n = 1, 2, 3, … A pipe closed at one end has a node at the closed end and an antinode at the open end: L = nλ/4 with odd n only, fn = n·v/(4L). When source or observer move along the line between them, f′ = f·(v ± vo)/(v ∓ vs): use the upper signs for motion towards each other. Two waves of nearly equal frequency beat at |f₁ − f₂|.
Geometric optics: at a boundary, n₁·sin θ₁ = n₂·sin θ₂ (Snell's law), with angles measured from the normal and n = c/v. Going into a slower medium the ray bends towards the normal. From a denser medium (n₁ > n₂) beyond the critical angle θc = arcsin(n₂/n₁) all light is reflected: total internal reflection. Thin lenses and spherical mirrors obey 1/f = 1/do + 1/di with the magnification m = −di/do. Sign convention: f > 0 for a converging lens and a concave mirror (f = R/2), f < 0 for a diverging lens and a convex mirror; di > 0 for a real image, di < 0 for a virtual one, and m < 0 for an inverted image.