Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A car driving at 120 km/h brakes with a constant deceleration of 6.5 m/s² until it stops. Find the braking distance s.
v₀ = 120 km/ha = −6.5 m/s²v = 0
s = m
2.KinematicsHard
A stone is dropped from rest into a well. The splash is heard 1.9 s after the stone is released. The speed of sound is 343 m/s; ignore air resistance and use g = 9.81 m/s². Find the depth d of the well.
ttotal = 1.9 svsound = 343 m/sg = 9.81 m/s²
d = m
3.Newton’s lawsMedium
A 19 kg block slides down a slope at 45° to the horizontal. The coefficient of kinetic friction is 0.25. Use g = 9.81 m/s². Find the acceleration a of the block along the slope.
m = 19 kgθ = 45°μ = 0.25g = 9.81 m/s²
a = m/s²
4.Newton’s lawsHard
A 1 kg block on a horizontal table is connected by a light string over a frictionless pulley to a hanging 2.5 kg mass. The coefficient of kinetic friction between block and table is 0.1. Use g = 9.81 m/s². Find the acceleration a of the system.
m1 = 1 kgm2 = 2.5 kgμ = 0.1g = 9.81 m/s²
a = m/s²
5.Projectile motionMedium
A ball is launched from level ground at 70° above the horizontal and lands 135 m away. Ignore air resistance and use g = 9.81 m/s². Find the launch speed v0.
θ = 70°R = 135 mg = 9.81 m/s²
v0 = m/s
6.Projectile motionHard
A ball is launched at 55° above horizontal from the top of a 20 m cliff. Ignore air resistance. Find the horizontal distance x travelled before the ball hits the ground.
v0 = 29 m/sθ = 55°h = 20 mg = 9.81 m/s²
x = m
7.Work & energyMedium
A block slides from rest down a slope at 25° to the horizontal. The coefficient of kinetic friction is 0.25. Find its speed v after it has slid 8 m along the slope.
θ = 25°μ = 0.25d = 8 mg = 9.81 m/s²
v = m/s
8.Work & energyHard
A 0.5 kg block is released from rest at height 3.5 m on a smooth ramp. At the bottom it crosses a rough horizontal strip 1.5 m long (μ = 0.25) and then runs onto a spring (k = 1000 N/m) on a smooth surface. Find the maximum compression x of the spring.
m = 0.5 kgh = 3.5 mL = 1.5 mμ = 0.25k = 1000 N/mg = 9.81 m/s²
x = cm
9.Momentum & collisionsMedium
A 1 kg glider moving at 3 m/s makes a perfectly elastic head-on collision with a 5 kg glider at rest on a frictionless track. Find the velocity v′2 of the second glider after the collision.
m1 = 1 kgm2 = 5 kgv1 = 3 m/sv2 = 0
v′2 = m/s
10.Momentum & collisionsHard
At a crossing a 1200 kg car travelling east at 21 m/s collides with a 1800 kg car travelling north at 12 m/s. The cars lock together. Find the speed v′ of the wreck just after the collision.
m1 = 1200 kgv1 = 21 m/s (E)m2 = 1800 kgv2 = 12 m/s (N)
v′ = m/s
11.Hydrostatic forceMedium
A vertical rectangular gate 1 m wide sits in the wall of a tank of water, with its top edge 2 m below the surface. Find the resultant hydrostatic force F on the gate.
A vertical rectangular gate 1 m wide sits in the wall of a tank of seawater, with its top edge 0.5 m below the surface. Find the resultant hydrostatic force F on the gate.
Water flows through a horizontal pipe that narrows from 100 mm to 75 mm. In the wide section the pressure is 250 kPa and the velocity is 2.75 m/s. Ignoring losses, find the pressure p2 in the narrow section.
Water flows up through a pipe that narrows from 200 mm to 100 mm while rising 6 m. At section 1 the pressure is 210 kPa and the velocity is 2.25 m/s. Ignoring losses, find the pressure p2 at section 2.
A reversible refrigerator keeps a cold room at 4 °C by removing 8 kW of heat, and rejects heat to the surroundings at 25 °C. Find the rate Q̇H at which it rejects heat.
TL = 4 °CTH = 25 °CQ̇L = 8 kW
Q̇H = kW
18.Heat engines & refrigeratorsHard
A heat pump delivers 17.5 kW of heat to a heating system at 55 °C, taking heat from a source at 0 °C. Its actual COP is 40% of the Carnot COP between these temperatures. Find the electrical power Ẇ it uses.
TH = 55 °CTL = 0 °CηII = 40%Q̇H = 17.5 kW
Ẇ = kW
19.Waves, sound & opticsMedium
A string fixed at both ends is 1.5 m long; waves travel on it at 100 m/s. Find the frequency f2 of its harmonic number 2.
v = 100 m/sn = 2L = 1.5 m
f2 = Hz
20.Waves, sound & opticsHard
Light of wavelength 600 nm passes through a single slit 0.12 mm wide. Find the angle θ1 of dark fringe number 1 from the straight-through direction.
λ = 600 nma = 0.12 mmm = 1
θ1 = °
3Solutions
1.Kinematics
Answer: s = 85.47 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Units
v₀ = 120/3.6 = 33.33 m/s
Braking distance
0 = v₀² − 2·a·s → s = v₀²/(2a) = 33.33²/(2·6.5) = 85.47 m
Answer
s = 85.47 m
2.Kinematics
Answer: d = 16.81 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Two parts of the time
½·9.81·t₁² = 343·(1.9 − t₁)
4.905·t₁² + 343·t₁ − 651.7 = 0
Fall time
Only the positive root is physical.
t₁ = (−343 + √(343² + 4·4.905·651.7))/(2·4.905) = 1.851 s
Depth
d = ½·9.81·1.851² = 16.81 m
Answer
d = 16.81 m
3.Newton’s laws
Answer: a = 5.203 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Solve the range formula for v₀
v₀ = √(g·R/sin 2θ) = √(9.81·135/sin 140°) = 45.39 m/s
Answer
v0 = 45.39 m/s
6.Projectile motion
Answer: x = 92.73 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 29·cos 55° = 16.63 m/s
vy = v0·sin θ = 29·sin 55° = 23.76 m/s
Time in the air
Solve y(t) = h + vy·t − ½gt² = 0 for the positive root.
0 = 20 + 23.76·t − 4.905·t²
t = (vy + √(vy² + 2gh))/g = (23.76 + √(564.3 + 392.4))/9.81 = 5.575 s
Horizontal distance
x = vx·t = 16.63·5.575 = 92.73 m
Answer
x = 92.73 m
7.Work & energy
Answer: v = 5.547 m/s
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy balance along the slope
The block drops a height d·sin θ while friction removes μmg·cos θ·d. The mass cancels.
½v² = g·d·(sin θ − μ·cos θ)
v = √(2·9.81·8·(0.4226 − 0.25·0.9063)) = 5.547 m/s
Answer
v = 5.547 m/s
8.Work & energy
Answer: x = 17.51 cm
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy left after the rough strip
The ramp is smooth, so only the strip removes energy.
mgh − μmgL = 4.905·(3.5 − 0.25·1.5) = 15.33 J
Maximum compression
½kx² = 15.33 → x = √(2·15.33/1000) = 0.1751 m = 17.51 cm
Answer
x = 17.51 cm
9.Momentum & collisions
Answer: v′2 = 1 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Elastic collision with a target at rest
Solving momentum and energy conservation together gives these two results.
v′1 = (1 − 5)/(1 + 5)·3 = −2 m/s
v′2 = 2·1/(1 + 5)·3 = 1 m/s
Answer
v′2 = 1 m/s
10.Momentum & collisions
Answer: v′ = 11.06 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 2 + 1.5/2 = 2.75 m
A = H·b = 1.5·1 = 1.5 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·2.75·1.5 = 40.47 kN
Answer
F = 40.47 kN
12.Hydrostatic force
Answer: F = 43.99 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 0.5 + 2.5/2 = 1.75 m
A = H·b = 2.5·1 = 2.5 m²
Resultant force
F = ρ·g·yc·A = 1025·9.81·1.75·2.5 = 43.99 kN
Answer
F = 43.99 kN
13.Continuity & Bernoulli
Answer: p2 = 241.8 kPa
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Combined gas law: for a fixed amount of ideal gas, P1V1/T1 = P2V2/T2.
Absolute temperatures
T1 = 303.1 K, T2 = 463.1 K
Combined gas law
V2 = V1·(P1/P2)·(T2/T1) = 10·(100/150)·(463.1/303.1) = 10.19 L
Answer
V2 = 10.19 L
17.Heat engines & refrigerators
Answer: Q̇H = 8.606 kW
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 25 + 273.15 = 298.1 K
TL = 4 + 273.15 = 277.1 K
Reversible heat ratio
Q̇H = Q̇L·TH/TL = 8·298.1/277.1 = 8.606 kW
Answer
Q̇H = 8.606 kW
Power input: Ẇ = 0.6062 kW.
18.Heat engines & refrigerators
Answer: Ẇ = 7.333 kW
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 55 + 273.15 = 328.1 K
TL = 0 + 273.15 = 273.1 K
Carnot and actual COP
COPmax = 328.1/(328.1 − 273.1) = 5.966
COP = 0.4·5.966 = 2.387
Power input
Ẇ = Q̇H/COP = 17.5/2.387 = 7.333 kW
Answer
Ẇ = 7.333 kW
19.Waves, sound & optics
Answer: f2 = 66.67 Hz
Standing waves and the Doppler effect: a string fixed at both ends, or a pipe open at both ends, fits whole half-wavelengths: L = nλ/2, fn = n·v/(2L), n = 1, 2, 3, … A pipe closed at one end has a node at the closed end and an antinode at the open end: L = nλ/4 with odd n only, fn = n·v/(4L). When source or observer move along the line between them, f′ = f·(v ± vo)/(v ∓ vs): use the upper signs for motion towards each other. Two waves of nearly equal frequency beat at |f₁ − f₂|.
Wavelength of this mode
λ = 2L/n = 2·1.5/2 = 1.5 m
Frequency
f = v/λ = 100/1.5 = 66.67 Hz
Answer
f2 = 66.67 Hz
20.Waves, sound & optics
Answer: θ1 = 0.2865 °
Interference and diffraction: light from two slits a distance d apart reaches a point on the screen with a path difference d·sin θ. Bright fringes appear where d·sin θ = mλ (m = 0, ±1, ±2, …). For a screen at distance L ≫ d, the m-th bright fringe is at y = mλL/d and the fringe spacing is Δy = λL/d. A grating with N lines per millimetre has d = 1/N and sharp maxima at d·sin θ = mλ; since sin θ ≤ 1, the highest order is the largest whole number m ≤ d/λ. A single slit of width a has dark fringes at a·sin θ = mλ, m = ±1, ±2, …