Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A car driving at 90 km/h brakes with a constant deceleration of 4.5 m/s² until it stops. How long does braking take? Find t.
v₀ = 90 km/ha = −4.5 m/s²v = 0
t = s
2.KinematicsHard
A tram starts from rest and accelerates at 2.5 m/s² for 11 s, then runs at constant speed for 23 s, and finally brakes at 3.5 m/s² until it stops. Find the total travel time t.
a1 = 2.5 m/s²t1 = 11 st2 = 23 sa3 = −3.5 m/s²
t = s
3.Newton’s lawsMedium
A 25 kg box is pushed up a ramp at 20° to the horizontal at constant speed, by a force parallel to the ramp. The coefficient of kinetic friction is 0.25. Use g = 9.81 m/s². Find the pushing force F.
m = 25 kgθ = 20°μ = 0.25g = 9.81 m/s²
F = N
4.Newton’s lawsHard
Two blocks on a level floor are joined by a light horizontal string. A horizontal force of 85 N pulls the front 9 kg block; the 1 kg block is towed behind. The coefficient of kinetic friction is 0.25 for both blocks. Use g = 9.81 m/s². Find the tension T in the connecting string.
m1 = 1 kgm2 = 9 kgF = 85 Nμ = 0.25g = 9.81 m/s²
T = N
5.Projectile motionMedium
A ball is kicked from level ground at 40 m/s and 55° above the horizontal towards a wall 123 m away. Ignore air resistance and use g = 9.81 m/s². At what height y does the ball pass the wall?
v₀ = 40 m/sθ = 55°x = 123 mg = 9.81 m/s²
y = m
6.Projectile motionHard
A ball is thrown from ground level at 26 m/s and 60° above the horizontal. It lands on the flat roof of a building 18 m high, on its way down. Ignore air resistance and use g = 9.81 m/s². Find the horizontal distance x from the launch point to where it lands.
v₀ = 26 m/sθ = 60°hroof = 18 mg = 9.81 m/s²
x = m
7.Work & energyMedium
A toy launcher has a vertical spring of stiffness 500 N/m. A 0.25 kg ball is placed on it and the spring is compressed by 6 cm, then released. Ignoring air resistance and the spring’s mass, find the height h the ball rises, measured from its position when the spring was compressed.
m = 0.25 kgk = 500 N/mx = 6 cmg = 9.81 m/s²
h = m
8.Work & energyHard
A 4 kg block is released from rest at height 1 m on a smooth ramp. At the bottom it crosses a rough horizontal strip 4.5 m long (μ = 0.1) and then runs onto a spring (k = 2500 N/m) on a smooth surface. Find the maximum compression x of the spring.
m = 4 kgh = 1 mL = 4.5 mμ = 0.1k = 2500 N/mg = 9.81 m/s²
x = cm
9.Momentum & collisionsMedium
A 2 kg glider moving at 10 m/s makes a perfectly elastic head-on collision with a 0.5 kg glider at rest on a frictionless track. Find the velocity v′1 of the first glider after the collision (positive in its original direction).
m1 = 2 kgm2 = 0.5 kgv1 = 10 m/sv2 = 0
v′1 = m/s
10.Momentum & collisionsHard
A 0.25 kg ball hits a wall at 14 m/s and bounces straight back at 8 m/s. The contact lasts 20 ms. Find the magnitude of the impulse J the wall gives the ball.
m = 0.25 kgvin = 14 m/svout = 8 m/sΔt = 20 ms
J = N·s
11.Hydrostatic forceMedium
A vertical rectangular gate 1 m wide sits in the wall of a tank of water, with its top edge 1.5 m below the surface. Find the resultant hydrostatic force F on the gate.
A vertical rectangular gate 3 m wide sits in the wall of a tank of seawater, with its top edge 4 m below the surface. Find the depth ycp of the centre of pressure below the surface.
Water flows through a horizontal pipe that narrows from 75 mm to 50 mm. In the wide section the pressure is 100 kPa and the velocity is 0.75 m/s. Ignoring losses, find the pressure p2 in the narrow section.
Water flows up through a pipe that narrows from 150 mm to 100 mm while rising 6 m. At section 1 the pressure is 310 kPa and the velocity is 1.5 m/s. Ignoring losses, find the pressure p2 at section 2.
A reversible (Carnot) heat engine takes in 5000 kJ of heat from a reservoir at 775 °C and rejects 1375 kJ per cycle. Find the temperature TL of the cold reservoir in °C.
TH = 775 °CQH = 5000 kJQL = 1375 kJ
TL = °C
18.Heat engines & refrigeratorsHard
A refrigerator keeps its cold space at -25 °C in a kitchen at 32 °C, removing heat from the cold space at 5 kW. Find the minimum power input Ẇmin.
TH = 32 °CTL = -25 °CQ̇L = 5 kW
Ẇmin = kW
19.Waves, sound & opticsMedium
A pipe closed at one end is 0.5 m long. The speed of sound is 343 m/s. Find the frequency f3 of its harmonic number 3.
v = 343 m/sn = 3L = 0.5 m
f3 = Hz
20.Waves, sound & opticsHard
Light of wavelength 450 nm passes through a single slit 0.2 mm wide. Find the width w of the central bright maximum on a screen 2 m away (between the first dark fringes on either side).
λ = 450 nma = 0.2 mmL = 2 m
w = mm
3Solutions
1.Kinematics
Answer: t = 5.556 s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Units
v₀ = 90/3.6 = 25 m/s
Braking time
0 = v₀ − a·t → t = v₀/a = 25/4.5 = 5.556 s
Answer
t = 5.556 s
2.Kinematics
Answer: t = 41.86 s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Top speed
v = a1·t1 = 2.5·11 = 27.5 m/s
Braking time
t3 = v/a3 = 27.5/3.5 = 7.857 s
Total time
t = 11 + 23 + 7.857 = 41.86 s
Answer
t = 41.86 s
3.Newton’s laws
Answer: F = 141.5 N
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Forces along the slope
Constant speed: the forces balance.
F = m·g·sin θ + μ·m·g·cos θ
Pushing force
F = 83.88 + 57.61 = 141.5 N
Answer
F = 141.5 N
4.Newton’s laws
Answer: T = 8.5 N
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
With the same μ on both blocks, friction drops out: T = F·m₁/(m₁ + m₂).
5.Projectile motion
Answer: y = 34.69 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Time to the wall
vx = 40·cos 55° = 22.94 m/s
t = x/vx = 123/22.94 = 5.361 s
Height at that time
y = 32.77·5.361 − ½·9.81·5.361² = 34.69 m
Answer
y = 34.69 m
The ball is already on its way down at the wall.
6.Projectile motion
Answer: x = 46.28 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
vx = 13 m/s, vy = 22.52 m/s
Time to land on the roof
Larger root: the ball is descending.
18 = 22.52·t − 4.905·t²
t = (22.52 + √(22.52² − 2·9.81·18))/9.81 = 3.56 s
Horizontal distance
x = vx·t = 13·3.56 = 46.28 m
Answer
x = 46.28 m
7.Work & energy
Answer: h = 0.367 m
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Spring energy
x = 6 cm = 0.06 m
½kx² = ½·500·0.06² = 0.9 J
Height
m·g = 0.25·9.81 = 2.453 N
h = ½kx²/(mg) = 0.9/2.453 = 0.367 m
Answer
h = 0.367 m
8.Work & energy
Answer: x = 13.14 cm
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy left after the rough strip
The ramp is smooth, so only the strip removes energy.
mgh − μmgL = 39.24·(1 − 0.1·4.5) = 21.58 J
Maximum compression
½kx² = 21.58 → x = √(2·21.58/2500) = 0.1314 m = 13.14 cm
Answer
x = 13.14 cm
9.Momentum & collisions
Answer: v′1 = 6 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Elastic collision with a target at rest
Solving momentum and energy conservation together gives these two results.
v′1 = (2 − 0.5)/(2 + 0.5)·10 = 6 m/s
v′2 = 2·2/(2 + 0.5)·10 = 16 m/s
Answer
v′1 = 6 m/s
10.Momentum & collisions
Answer: J = 5.5 N·s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Change in momentum
J = m·Δv = 0.25·(8 + 14) = 5.5 N·s
Answer
J = 5.5 N·s
11.Hydrostatic force
Answer: F = 67.44 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 1.5 + 2.5/2 = 2.75 m
A = H·b = 2.5·1 = 2.5 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·2.75·2.5 = 67.44 kN
Answer
F = 67.44 kN
12.Hydrostatic force
Answer: ycp = 5.349 m
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 4 + 2.5/2 = 5.25 m
A = H·b = 2.5·3 = 7.5 m²
Resultant force
F = ρ·g·yc·A = 1025·9.81·5.25·7.5 = 395.9 kN
Centre of pressure
Pressure grows with depth, so the resultant acts below the centroid.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperature of the source
TH = 775 + 273.15 = 1048 K
Reversible heat ratio
TL = TH·QL/QH = 1048·1375/5000 = 288.2 K = 15.09 °C
Answer
TL = 15.09 °C
18.Heat engines & refrigerators
Answer: Ẇmin = 1.148 kW
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
The least work is needed by a reversible machine, which has the highest COP.
Ẇmin = Q̇L/COP = 5/4.354 = 1.148 kW
Answer
Ẇmin = 1.148 kW
19.Waves, sound & optics
Answer: f3 = 514.5 Hz
Standing waves and the Doppler effect: a string fixed at both ends, or a pipe open at both ends, fits whole half-wavelengths: L = nλ/2, fn = n·v/(2L), n = 1, 2, 3, … A pipe closed at one end has a node at the closed end and an antinode at the open end: L = nλ/4 with odd n only, fn = n·v/(4L). When source or observer move along the line between them, f′ = f·(v ± vo)/(v ∓ vs): use the upper signs for motion towards each other. Two waves of nearly equal frequency beat at |f₁ − f₂|.
Wavelength of this mode
λ = 4L/n = 4·0.5/3 = 0.6667 m
Frequency
f = v/λ = 343/0.6667 = 514.5 Hz
Answer
f3 = 514.5 Hz
20.Waves, sound & optics
Answer: w = 9 mm
Interference and diffraction: light from two slits a distance d apart reaches a point on the screen with a path difference d·sin θ. Bright fringes appear where d·sin θ = mλ (m = 0, ±1, ±2, …). For a screen at distance L ≫ d, the m-th bright fringe is at y = mλL/d and the fringe spacing is Δy = λL/d. A grating with N lines per millimetre has d = 1/N and sharp maxima at d·sin θ = mλ; since sin θ ≤ 1, the highest order is the largest whole number m ≤ d/λ. A single slit of width a has dark fringes at a·sin θ = mλ, m = ±1, ±2, …