Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A car driving at 108 km/h brakes with a constant deceleration of 3 m/s² until it stops. How long does braking take? Find t.
v₀ = 108 km/ha = −3 m/s²v = 0
t = s
2.KinematicsHard
A ball is thrown straight up at 19 m/s from the edge of a roof 10 m above the ground. Ignore air resistance and use g = 9.81 m/s². Find the greatest height hmax above the ground.
v₀ = 19 m/sh₀ = 10 mg = 9.81 m/s²
hmax = m
3.Newton’s lawsMedium
A 9 kg block slides down a frictionless slope at 30° to the horizontal. Use g = 9.81 m/s². Find the acceleration a of the block along the slope.
m = 9 kgθ = 30°μ = 0g = 9.81 m/s²
a = m/s²
4.Newton’s lawsHard
A 3.5 kg block on a ramp at 25° is connected by a light string over a frictionless pulley at the top of the ramp to a hanging 5 kg mass. The hanging mass moves down. The coefficient of kinetic friction between block and ramp is 0.25. Use g = 9.81 m/s². Find the acceleration a of the system.
m1 = 3.5 kgm2 = 5 kgθ = 25°μ = 0.25g = 9.81 m/s²
a = m/s²
5.Projectile motionMedium
A ball is launched from level ground at 60° above the horizontal and lands 50 m away. Ignore air resistance and use g = 9.81 m/s². Find the launch speed v0.
θ = 60°R = 50 mg = 9.81 m/s²
v0 = m/s
6.Projectile motionHard
A ball is thrown from ground level at 38 m/s and 70° above the horizontal. It lands on the flat roof of a building 4 m high, on its way down. Ignore air resistance and use g = 9.81 m/s². Find the horizontal distance x from the launch point to where it lands.
v₀ = 38 m/sθ = 70°hroof = 4 mg = 9.81 m/s²
x = m
7.Work & energyMedium
A block slides from rest down a slope at 45° to the horizontal. The coefficient of kinetic friction is 0.4. Find its speed v after it has slid 14 m along the slope.
θ = 45°μ = 0.4d = 14 mg = 9.81 m/s²
v = m/s
8.Work & energyHard
A 10 kg block is released from rest at height 4.5 m on a smooth ramp. At the bottom it crosses a rough horizontal strip 2 m long (μ = 0.3) and then runs onto a spring (k = 1000 N/m) on a smooth surface. Find the speed v of the block when it reaches the spring.
m = 10 kgh = 4.5 mL = 2 mμ = 0.3k = 1000 N/mg = 9.81 m/s²
v = m/s
9.Momentum & collisionsMedium
A 2 kg glider moving at 5 m/s makes a perfectly elastic head-on collision with a 5 kg glider at rest on a frictionless track. Find the velocity v′2 of the second glider after the collision.
m1 = 2 kgm2 = 5 kgv1 = 5 m/sv2 = 0
v′2 = m/s
10.Momentum & collisionsHard
A 10 g bullet is fired horizontally into a 1.5 kg block hanging from light strings 0.6 m long, and stays in it. The strings swing out to a largest angle of 15° from the vertical. Use g = 9.81 m/s². Find the speed v of the bullet before impact.
m = 10 gM = 1.5 kgL = 0.6 mθ = 15°g = 9.81 m/s²
v = m/s
11.Hydrostatic forceMedium
A vertical rectangular gate 1.5 m wide sits in the wall of a tank of water, with its top edge 2 m below the surface. Find the resultant hydrostatic force F on the gate.
A vertical rectangular gate 1 m wide sits in the wall of a tank of oil, with its top edge 1.5 m below the surface. Find the resultant hydrostatic force F on the gate.
d = 1.5 mH = 3 mb = 1 mρ = 880 kg/m³g = 9.81 m/s²
F = kN
13.Continuity & BernoulliMedium
Water drains from a large open tank through a sharp-edged orifice with a diameter of 30 mm. The water level is kept 4.5 m above the orifice and the discharge coefficient is 0.62. Find the flow rate Q. Use g = 9.81 m/s².
d = 30 mmh = 4.5 mCd = 0.62g = 9.81 m/s²
Q = L/s
14.Continuity & BernoulliHard
Water flows up through a pipe that narrows from 100 mm to 75 mm while rising 5 m. At section 1 the pressure is 260 kPa and the velocity is 1.5 m/s. Ignoring losses, find the pressure p2 at section 2.
A heat engine works between a hot reservoir at 775 °C and a cold reservoir at 25 °C. Find the highest possible thermal efficiency ηmax.
TH = 775 °CTL = 25 °C
ηmax = %
18.Heat engines & refrigeratorsHard
A heat pump keeps a house at 22 °C while it is -5 °C outside, delivering 15 kW of heat to the house. Find the minimum power input Ẇmin.
TH = 22 °CTL = -5 °CQ̇H = 15 kW
Ẇmin = kW
19.Waves, sound & opticsMedium
A pipe closed at one end must have its harmonic number 7 at 1201 Hz. The speed of sound is 343 m/s. Find the length L of the pipe.
v = 343 m/sn = 7f7 = 1201 Hz
L = m
20.Waves, sound & opticsHard
Two thin lenses share an axis, 50 cm apart: lens 1 with f₁ = 15 cm and lens 2 with f₂ = 15 cm. An object stands 50 cm in front of lens 1. Find the position di2 of the final image measured from lens 2 (positive beyond lens 2, real-is-positive convention).
f1 = 15 cmf2 = 15 cms = 50 cmdo = 50 cm
di2 = cm
3Solutions
1.Kinematics
Answer: t = 10 s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Units
v₀ = 108/3.6 = 30 m/s
Braking time
0 = v₀ − a·t → t = v₀/a = 30/3 = 10 s
Answer
t = 10 s
2.Kinematics
Answer: hmax = 28.4 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Rise above the roof
0 = v₀² − 2·g·Δh → Δh = 19²/(2·9.81) = 18.4 m
Height above the ground
hmax = 10 + 18.4 = 28.4 m
Answer
hmax = 28.4 m
3.Newton’s laws
Answer: a = 4.905 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Forces along the string
m₂·g = 49.05 N
m₁·g·sin θ = 14.51 N
μ·m₁·g·cos θ = 7.78 N
Acceleration of the system
a = (49.05 − 14.51 − 7.78)/8.5 = 3.148 m/s²
Answer
a = 3.148 m/s²
5.Projectile motion
Answer: v0 = 23.8 m/s
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Solve the range formula for v₀
v₀ = √(g·R/sin 2θ) = √(9.81·50/sin 120°) = 23.8 m/s
Answer
v0 = 23.8 m/s
6.Projectile motion
Answer: x = 93.14 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
vx = 13 m/s, vy = 35.71 m/s
Time to land on the roof
Larger root: the ball is descending.
4 = 35.71·t − 4.905·t²
t = (35.71 + √(35.71² − 2·9.81·4))/9.81 = 7.166 s
Horizontal distance
x = vx·t = 13·7.166 = 93.14 m
Answer
x = 93.14 m
7.Work & energy
Answer: v = 10.8 m/s
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy balance along the slope
The block drops a height d·sin θ while friction removes μmg·cos θ·d. The mass cancels.
½v² = g·d·(sin θ − μ·cos θ)
v = √(2·9.81·14·(0.7071 − 0.4·0.7071)) = 10.8 m/s
Answer
v = 10.8 m/s
8.Work & energy
Answer: v = 8.747 m/s
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy left after the rough strip
The ramp is smooth, so only the strip removes energy.
mgh − μmgL = 98.1·(4.5 − 0.3·2) = 382.6 J
Speed at the spring
½mv² = mg(h − μL) → v = √(2g(h − μL)) = √(2·9.81·3.9) = 8.747 m/s
Answer
v = 8.747 m/s
9.Momentum & collisions
Answer: v′2 = 2.857 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Elastic collision with a target at rest
Solving momentum and energy conservation together gives these two results.
v′1 = (2 − 5)/(2 + 5)·5 = −2.143 m/s
v′2 = 2·2/(2 + 5)·5 = 2.857 m/s
Answer
v′2 = 2.857 m/s
10.Momentum & collisions
Answer: v = 95.63 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Rise of the block
h = L·(1 − cos θ) = 0.6·(1 − cos 15°) = 0.02044 m
Speed after impact
V = √(2·9.81·0.02044) = 0.6333 m/s
Collision
v = (m + M)·V/m = 1.51·0.6333/0.01 = 95.63 m/s
Answer
v = 95.63 m/s
11.Hydrostatic force
Answer: F = 88.29 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 2 + 2/2 = 3 m
A = H·b = 2·1.5 = 3 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·3·3 = 88.29 kN
Answer
F = 88.29 kN
12.Hydrostatic force
Answer: F = 77.7 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 1.5 + 3/2 = 3 m
A = H·b = 3·1 = 3 m²
Resultant force
F = ρ·g·yc·A = 880·9.81·3·3 = 77.7 kN
Answer
F = 77.7 kN
13.Continuity & Bernoulli
Answer: Q = 4.118 L/s
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Ideal jet velocity
√(2gh) = √(2·9.81·4.5) = 9.396 m/s
Actual flow rate
The discharge coefficient accounts for the contraction of the jet and friction at the edge.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 775 + 273.15 = 1048 K
TL = 25 + 273.15 = 298.1 K
Carnot efficiency
ηmax = 1 − TL/TH = 1 − 298.1/1048 = 71.55 %
Answer
ηmax = 71.55 %
18.Heat engines & refrigerators
Answer: Ẇmin = 1.372 kW
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
The least work is needed by a reversible machine, which has the highest COP.
Ẇmin = Q̇H/COP = 15/10.93 = 1.372 kW
Answer
Ẇmin = 1.372 kW
19.Waves, sound & optics
Answer: L = 0.4998 m
Standing waves and the Doppler effect: a string fixed at both ends, or a pipe open at both ends, fits whole half-wavelengths: L = nλ/2, fn = n·v/(2L), n = 1, 2, 3, … A pipe closed at one end has a node at the closed end and an antinode at the open end: L = nλ/4 with odd n only, fn = n·v/(4L). When source or observer move along the line between them, f′ = f·(v ± vo)/(v ∓ vs): use the upper signs for motion towards each other. Two waves of nearly equal frequency beat at |f₁ − f₂|.
Wavelength
λ = v/f = 343/1201 = 0.2856 m
Length
L = nλ/4 = 7·0.2856/4 = 0.4998 m
Answer
L = 0.4998 m
20.Waves, sound & optics
Answer: di2 = 31.58 cm
Geometric optics: at a boundary, n₁·sin θ₁ = n₂·sin θ₂ (Snell's law), with angles measured from the normal and n = c/v. Going into a slower medium the ray bends towards the normal. From a denser medium (n₁ > n₂) beyond the critical angle θc = arcsin(n₂/n₁) all light is reflected: total internal reflection. Thin lenses and spherical mirrors obey 1/f = 1/do + 1/di with the magnification m = −di/do. Sign convention: f > 0 for a converging lens and a concave mirror (f = R/2), f < 0 for a diverging lens and a convex mirror; di > 0 for a real image, di < 0 for a virtual one, and m < 0 for an inverted image.