Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A car speeding at a constant 29 m/s passes a police car standing still. At that moment the police car starts and accelerates uniformly at 6 m/s². How far from its starting point does the police car catch up? Find d.
vcar = 29 m/sapolice = 6 m/s²v0,police = 0
d = m
2.KinematicsHard
A model rocket is launched straight up from rest. Its engine gives it a constant upward acceleration of 30 m/s² for 2 s, after which the engine stops and the rocket moves freely. Ignore air resistance and use g = 9.81 m/s². Find the greatest height hmax the rocket reaches.
a = 30 m/s²t1 = 2 sg = 9.81 m/s²
hmax = m
3.Newton’s lawsMedium
A 9 kg block slides down a slope at 45° to the horizontal. The coefficient of kinetic friction is 0.3. Use g = 9.81 m/s². Find the acceleration a of the block along the slope.
m = 9 kgθ = 45°μ = 0.3g = 9.81 m/s²
a = m/s²
4.Newton’s lawsHard
Two blocks on a level floor are joined by a light horizontal string. A horizontal force of 120 N pulls the front 1 kg block; the 8 kg block is towed behind. The coefficient of kinetic friction is 0.15 for both blocks. Use g = 9.81 m/s². Find the tension T in the connecting string.
m1 = 8 kgm2 = 1 kgF = 120 Nμ = 0.15g = 9.81 m/s²
T = N
5.Projectile motionMedium
A ball is launched from level ground at 36 m/s and must land 70 m away. Ignore air resistance and use g = 9.81 m/s². Find the smaller of the two possible launch angles θ.
v₀ = 36 m/sR = 70 mg = 9.81 m/s²
θ = °
6.Projectile motionHard
A ball is launched at 45° above horizontal from the top of a 60 m cliff. Ignore air resistance. Find the horizontal distance x travelled before the ball hits the ground.
v0 = 28 m/sθ = 45°h = 60 mg = 9.81 m/s²
x = m
7.Work & energyMedium
A toy launcher has a vertical spring of stiffness 500 N/m. A 0.25 kg ball is placed on it and the spring is compressed by 10 cm, then released. Ignoring air resistance and the spring’s mass, find the height h the ball rises, measured from its position when the spring was compressed.
m = 0.25 kgk = 500 N/mx = 10 cmg = 9.81 m/s²
h = m
8.Work & energyHard
A 15 kg block starts from rest at the bottom of a 35° slope and is pulled up the slope by a constant force of 195 N parallel to the slope. The coefficient of kinetic friction is 0.1. Find the speed v of the block after it has moved 7 m up the slope.
A 5 kg glider moving at 11 m/s makes a perfectly elastic head-on collision with a 3 kg glider at rest on a frictionless track. Find the velocity v′1 of the first glider after the collision (positive in its original direction).
m1 = 5 kgm2 = 3 kgv1 = 11 m/sv2 = 0
v′1 = m/s
10.Momentum & collisionsHard
At a crossing a 1600 kg car travelling east at 14 m/s collides with a 2000 kg car travelling north at 12 m/s. The cars lock together. Find the direction θ of the wreck just after the collision, measured north of east.
m1 = 1600 kgv1 = 14 m/s (E)m2 = 2000 kgv2 = 12 m/s (N)
θ = °
11.Hydrostatic forceMedium
A vertical rectangular gate 1 m wide sits in the wall of a tank of water, with its top edge 3 m below the surface. Find the resultant hydrostatic force F on the gate.
A vertical rectangular gate 2 m wide sits in the wall of a tank of water, with its top edge 2 m below the surface. Find the resultant hydrostatic force F on the gate.
Water flows through a horizontal pipe that narrows from 100 mm to 75 mm. In the wide section the pressure is 150 kPa and the velocity is 1 m/s. Ignoring losses, find the pressure p2 in the narrow section.
Water flows up through a pipe that narrows from 75 mm to 50 mm while rising 3 m. At section 1 the pressure is 330 kPa and the velocity is 1.25 m/s. Ignoring losses, find the pressure p2 at section 2.
A heat engine works between a hot reservoir at 300 °C and a cold reservoir at 15 °C. Find the highest possible thermal efficiency ηmax.
TH = 300 °CTL = 15 °C
ηmax = %
18.Heat engines & refrigeratorsHard
A heat pump keeps a house at 21 °C while it is 0 °C outside, delivering 8 kW of heat to the house. Find the highest possible coefficient of performance COPmax.
TH = 21 °CTL = 0 °CQ̇H = 8 kW
COPmax =
19.Waves, sound & opticsMedium
A source of 600 Hz moves at 34 m/s towards a stationary observer. The speed of sound is 343 m/s. Find the frequency f′ that the observer hears.
f = 600 Hzv = 343 m/svs = 34 m/s
f′ = Hz
20.Waves, sound & opticsHard
Two thin lenses share an axis, 10 cm apart: lens 1 with f₁ = 15 cm and lens 2 with f₂ = 20 cm. An object stands 40 cm in front of lens 1. Find the position di2 of the final image measured from lens 2 (positive beyond lens 2, real-is-positive convention).
f1 = 15 cmf2 = 20 cms = 10 cmdo = 40 cm
di2 = cm
3Solutions
1.Kinematics
Answer: d = 280.3 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Equal distances
v·t = ½·a·t² → t = 2v/a = 2·29/6 = 9.667 s
Distance
d = v·t = 29·9.667 = 280.3 m
Answer
d = 280.3 m
At that moment the police car moves at 2v = 58 m/s.
2.Kinematics
Answer: hmax = 243.5 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Powered phase
v₁ = 30·2 = 60 m/s
h₁ = ½·30·2² = 60 m
Free flight up
At the top the velocity is zero.
Δh = v₁²/(2g) = 60²/(2·9.81) = 183.5 m
hmax = 60 + 183.5 = 243.5 m
Answer
hmax = 243.5 m
3.Newton’s laws
Answer: a = 4.856 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
With the same μ on both blocks, friction drops out: T = F·m₁/(m₁ + m₂).
5.Projectile motion
Answer: θ = 16 °
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Range formula
R = v₀²·sin 2θ/g → sin 2θ = 9.81·70/36² = 0.5299
Angle
2θ = 32° → θ = 16°
Answer
θ = 16°
The other solution is 90° − θ = 74°.
6.Projectile motion
Answer: x = 119.9 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 28·cos 45° = 19.8 m/s
vy = v0·sin θ = 28·sin 45° = 19.8 m/s
Time in the air
Solve y(t) = h + vy·t − ½gt² = 0 for the positive root.
0 = 60 + 19.8·t − 4.905·t²
t = (vy + √(vy² + 2gh))/g = (19.8 + √(392 + 1177))/9.81 = 6.056 s
Horizontal distance
x = vx·t = 19.8·6.056 = 119.9 m
Answer
x = 119.9 m
7.Work & energy
Answer: h = 1.019 m
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Spring energy
x = 10 cm = 0.1 m
½kx² = ½·500·0.1² = 2.5 J
Height
m·g = 0.25·9.81 = 2.453 N
h = ½kx²/(mg) = 2.5/2.453 = 1.019 m
Answer
h = 1.019 m
8.Work & energy
Answer: v = 9.59 m/s
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Forces along the slope
m·g = 15·9.81 = 147.2 N
mg·sin θ = 84.4 N
μ·mg·cos θ = 12.05 N
Work–energy
½mv² = (195 − 96.46)·7 = 689.8 J
v = √(2·689.8/15) = 9.59 m/s
Answer
v = 9.59 m/s
9.Momentum & collisions
Answer: v′1 = 2.75 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Elastic collision with a target at rest
Solving momentum and energy conservation together gives these two results.
v′1 = (5 − 3)/(5 + 3)·11 = 2.75 m/s
v′2 = 2·5/(5 + 3)·11 = 13.75 m/s
Answer
v′1 = 2.75 m/s
10.Momentum & collisions
Answer: θ = 46.97 °
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Momentum components
px = 1600·14 = 22400 kg·m/s
py = 2000·12 = 24000 kg·m/s
Direction
tan θ = py/px = 1.071 → θ = 46.97°
Answer
θ = 46.97°
11.Hydrostatic force
Answer: F = 104.2 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 3 + 2.5/2 = 4.25 m
A = H·b = 2.5·1 = 2.5 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·4.25·2.5 = 104.2 kN
Answer
F = 104.2 kN
12.Hydrostatic force
Answer: F = 159.4 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 2 + 2.5/2 = 3.25 m
A = H·b = 2.5·2 = 5 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·3.25·5 = 159.4 kN
Answer
F = 159.4 kN
13.Continuity & Bernoulli
Answer: p2 = 148.9 kPa
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Combined gas law: for a fixed amount of ideal gas, P1V1/T1 = P2V2/T2.
Absolute temperatures
T1 = 288.1 K, T2 = 323.1 K
Combined gas law
V2 = V1·(P1/P2)·(T2/T1) = 2·(350/450)·(323.1/288.1) = 1.745 L
Answer
V2 = 1.745 L
17.Heat engines & refrigerators
Answer: ηmax = 49.73 %
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 300 + 273.15 = 573.1 K
TL = 15 + 273.15 = 288.1 K
Carnot efficiency
ηmax = 1 − TL/TH = 1 − 288.1/573.1 = 49.73 %
Answer
ηmax = 49.73 %
18.Heat engines & refrigerators
Answer: COPmax = 14.01
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Standing waves and the Doppler effect: a string fixed at both ends, or a pipe open at both ends, fits whole half-wavelengths: L = nλ/2, fn = n·v/(2L), n = 1, 2, 3, … A pipe closed at one end has a node at the closed end and an antinode at the open end: L = nλ/4 with odd n only, fn = n·v/(4L). When source or observer move along the line between them, f′ = f·(v ± vo)/(v ∓ vs): use the upper signs for motion towards each other. Two waves of nearly equal frequency beat at |f₁ − f₂|.
Geometric optics: at a boundary, n₁·sin θ₁ = n₂·sin θ₂ (Snell's law), with angles measured from the normal and n = c/v. Going into a slower medium the ray bends towards the normal. From a denser medium (n₁ > n₂) beyond the critical angle θc = arcsin(n₂/n₁) all light is reflected: total internal reflection. Thin lenses and spherical mirrors obey 1/f = 1/do + 1/di with the magnification m = −di/do. Sign convention: f > 0 for a converging lens and a concave mirror (f = R/2), f < 0 for a diverging lens and a convex mirror; di > 0 for a real image, di < 0 for a virtual one, and m < 0 for an inverted image.