Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A plane starts from rest and accelerates uniformly at 3 m/s² along a runway. Find its speed v after 1900 m.
v₀ = 0a = 3 m/s²s = 1900 m
v = m/s
2.KinematicsHard
A tram starts from rest and accelerates at 2.5 m/s² for 6 s, then runs at constant speed for 8 s, and finally brakes at 3 m/s² until it stops. Find the total distance s between the two stops.
a1 = 2.5 m/s²t1 = 6 st2 = 8 sa3 = −3 m/s²
s = m
3.Newton’s lawsMedium
An 8 kg block slides down a frictionless slope at 45° to the horizontal. Use g = 9.81 m/s². Find the acceleration a of the block along the slope.
m = 8 kgθ = 45°μ = 0g = 9.81 m/s²
a = m/s²
4.Newton’s lawsHard
An 8 kg block on a horizontal table is connected by a light string over a frictionless pulley to a hanging 4 kg mass. The coefficient of kinetic friction between block and table is 0.3. Use g = 9.81 m/s². Find the tension T in the string.
m1 = 8 kgm2 = 4 kgμ = 0.3g = 9.81 m/s²
T = N
5.Projectile motionMedium
A ball is launched at 65° above horizontal from level ground. Ignore air resistance. Find the maximum height H the ball reaches.
v0 = 38 m/sθ = 65°g = 9.81 m/s²
H = m
6.Projectile motionHard
A ball is launched at 21 m/s and 40° above the horizontal from the top of a 5 m cliff. Ignore air resistance and use g = 9.81 m/s². Find the speed v with which it hits the ground.
v₀ = 21 m/sθ = 40°h = 5 mg = 9.81 m/s²
v = m/s
7.Work & energyMedium
A car travelling at 70 km/h on a level road brakes hard and skids to a stop with its wheels locked. The coefficient of kinetic friction between the tyres and the road is 0.7. Find the stopping distance d.
v = 70 km/hμ = 0.7g = 9.81 m/s²
d = m
8.Work & energyHard
A 4 kg block rests on a rough horizontal table (μ = 0.25). A light string runs from it over a smooth pulley at the edge of the table to a hanging 2 kg block. The system is released from rest. Find the speed v of the blocks after the hanging block has dropped 2 m.
m1 = 4 kgm2 = 2 kgμ = 0.25d = 2 mg = 9.81 m/s²
v = m/s
9.Momentum & collisionsMedium
A 3 kg glider moving at 10 m/s makes a perfectly elastic head-on collision with a 3.5 kg glider at rest on a frictionless track. Find the velocity v′1 of the first glider after the collision (positive in its original direction).
m1 = 3 kgm2 = 3.5 kgv1 = 10 m/sv2 = 0
v′1 = m/s
10.Momentum & collisionsHard
At a crossing a 1100 kg car travelling east at 19 m/s collides with a 1800 kg car travelling north at 16 m/s. The cars lock together. Find the speed v′ of the wreck just after the collision.
m1 = 1100 kgv1 = 19 m/s (E)m2 = 1800 kgv2 = 16 m/s (N)
v′ = m/s
11.Hydrostatic forceMedium
A vertical rectangular gate 1.5 m wide sits in the wall of a tank of water, with its top edge 0.5 m below the surface. Find the resultant hydrostatic force F on the gate.
A vertical rectangular gate 2 m wide sits in the wall of a tank of glycerin, with its top edge 2.5 m below the surface. Find the depth ycp of the centre of pressure below the surface.
Water flows through a horizontal pipe that narrows from 75 mm to 40 mm. In the wide section the pressure is 320 kPa and the velocity is 2 m/s. Ignoring losses, find the pressure p2 in the narrow section.
Water flows up through a pipe that narrows from 150 mm to 50 mm while rising 2 m. At section 1 the pressure is 270 kPa and the velocity is 0.75 m/s. Ignoring losses, find the pressure p2 at section 2.
A reversible (Carnot) heat engine takes in 4600 kJ of heat from a reservoir at 775 °C and rejects 1352 kJ per cycle. Find the temperature TL of the cold reservoir in °C.
TH = 775 °CQH = 4600 kJQL = 1352 kJ
TL = °C
18.Heat engines & refrigeratorsHard
Two Carnot engines work in series. Engine A receives heat from a reservoir at 750 °C and rejects heat to an intermediate reservoir at temperature Tm. Engine B takes all that heat and rejects heat to a reservoir at 40 °C. Both engines produce the same work. Find Tm in °C.
TH = 750 °CTL = 40 °C
Tm = °C
19.Waves, sound & opticsMedium
An object 2 cm tall stands 15 cm in front of a thin converging lens with a focal length of 20 cm. Find the image height hi (negative for an inverted image).
ho = 2 cmdo = 15 cmf = 20 cm
hi = cm
20.Waves, sound & opticsHard
A sensor at rest sends ultrasound of 40 kHz towards a car that approaches at 30 m/s and mixes the echo with the emitted signal. Find the beat frequency fb (speed of sound 343 m/s).
f = 40 kHzu = 30 m/sv = 343 m/s
fb = Hz
3Solutions
1.Kinematics
Answer: v = 106.8 m/s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Speed after the distance
v = √(2·a·s) = √(2·3·1900) = 106.8 m/s
Answer
v = 106.8 m/s
(384.4 km/h)
2.Kinematics
Answer: s = 202.5 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Top speed
v = a1·t1 = 2.5·6 = 15 m/s
Distance of each phase
s1 = ½·2.5·6² = 45 m
s2 = 15·8 = 120 m
s3 = 15²/(2·3) = 37.5 m
Total distance
s = 45 + 120 + 37.5 = 202.5 m
Answer
s = 202.5 m
3.Newton’s laws
Answer: a = 6.937 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 38·cos 65° = 16.06 m/s
vy = v0·sin θ = 38·sin 65° = 34.44 m/s
Highest point
At the top the vertical velocity is zero: vy² = 2gH.
H = vy²/(2g) = 34.44²/(2·9.81) = 60.45 m
Answer
H = 60.45 m
6.Projectile motion
Answer: v = 23.22 m/s
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
vx = 21·cos 40° = 16.09 m/s
vy0 = 21·sin 40° = 13.5 m/s
Vertical speed at impact
Energy or v² = v₀² + 2as in the vertical direction.
vy = √(13.5² + 2·9.81·5) = 16.74 m/s
Impact speed
v = √(16.09² + 16.74²) = 23.22 m/s
Answer
v = 23.22 m/s
Check with energy: v² = v₀² + 2gh.
7.Work & energy
Answer: d = 27.53 m
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Speed in base units
v = 70/3.6 = 19.44 m/s
Energy balance
½mv² = μmg·d → d = v²/(2μg) = 19.44²/(2·0.7·9.81) = 27.53 m
Answer
d = 27.53 m
Doubling the speed makes the stopping distance four times longer.
8.Work & energy
Answer: v = 2.557 m/s
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy released and lost
m₂g·d = 19.62·2 = 39.24 J
μ·m₁g·d = 0.25·39.24·2 = 19.62 J
Kinetic energy of both blocks
½(m₁ + m₂)v² = 19.62 → v = √(2·19.62/6) = 2.557 m/s
Answer
v = 2.557 m/s
9.Momentum & collisions
Answer: v′1 = −0.7692 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Elastic collision with a target at rest
Solving momentum and energy conservation together gives these two results.
v′1 = (3 − 3.5)/(3 + 3.5)·10 = −0.7692 m/s
v′2 = 2·3/(3 + 3.5)·10 = 9.231 m/s
Answer
v′1 = −0.7692 m/s
The minus sign means the first glider bounces back.
10.Momentum & collisions
Answer: v′ = 12.27 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 0.5 + 2/2 = 1.5 m
A = H·b = 2·1.5 = 3 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·1.5·3 = 44.15 kN
Answer
F = 44.15 kN
12.Hydrostatic force
Answer: ycp = 3.028 m
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 2.5 + 1/2 = 3 m
A = H·b = 1·2 = 2 m²
Resultant force
F = ρ·g·yc·A = 1260·9.81·3·2 = 74.16 kN
Centre of pressure
Pressure grows with depth, so the resultant acts below the centroid.
Ic = b·H³/12 = 2·1³/12 = 0.1667 m⁴
ycp = yc + Ic/(yc·A) = 3 + 0.1667/(3·2) = 3.028 m
Answer
ycp = 3.028 m
13.Continuity & Bernoulli
Answer: p2 = 297.3 kPa
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Combined gas law: for a fixed amount of ideal gas, P1V1/T1 = P2V2/T2.
Absolute temperatures
T1 = 308.1 K, T2 = 383.1 K
Combined gas law
V2 = V1·(P1/P2)·(T2/T1) = 10·(100/700)·(383.1/308.1) = 1.776 L
Answer
V2 = 1.776 L
17.Heat engines & refrigerators
Answer: TL = 34.91 °C
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperature of the source
TH = 775 + 273.15 = 1048 K
Reversible heat ratio
TL = TH·QL/QH = 1048·1352/4600 = 308.1 K = 34.91 °C
Answer
TL = 34.91 °C
18.Heat engines & refrigerators
Answer: Tm = 395 °C
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 750 + 273.15 = 1023 K
TL = 40 + 273.15 = 313.1 K
Equal work
W = Q·(1 − Tlow/Thigh) and Q/T is the same at every reservoir, so W is proportional to the temperature drop.
Tm = (1023 + 313.1)/2 = 668.1 K = 395 °C
Answer
Tm = 395 °C
19.Waves, sound & optics
Answer: hi = 8 cm
Geometric optics: at a boundary, n₁·sin θ₁ = n₂·sin θ₂ (Snell's law), with angles measured from the normal and n = c/v. Going into a slower medium the ray bends towards the normal. From a denser medium (n₁ > n₂) beyond the critical angle θc = arcsin(n₂/n₁) all light is reflected: total internal reflection. Thin lenses and spherical mirrors obey 1/f = 1/do + 1/di with the magnification m = −di/do. Sign convention: f > 0 for a converging lens and a concave mirror (f = R/2), f < 0 for a diverging lens and a convex mirror; di > 0 for a real image, di < 0 for a virtual one, and m < 0 for an inverted image.
Thin-lens equation
1/di = 1/f − 1/do = 1/20 − 1/15
di = −60 cm
Magnification and height
m = −(−60)/15 = 4
hi = 4·2 = 8 cm
Answer
hi = 8 cm
20.Waves, sound & optics
Answer: fb = 7668 Hz
Standing waves and the Doppler effect: a string fixed at both ends, or a pipe open at both ends, fits whole half-wavelengths: L = nλ/2, fn = n·v/(2L), n = 1, 2, 3, … A pipe closed at one end has a node at the closed end and an antinode at the open end: L = nλ/4 with odd n only, fn = n·v/(4L). When source or observer move along the line between them, f′ = f·(v ± vo)/(v ∓ vs): use the upper signs for motion towards each other. Two waves of nearly equal frequency beat at |f₁ − f₂|.