Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A car driving at 100 km/h brakes with a constant deceleration of 4.5 m/s² until it stops. How long does braking take? Find t.
v₀ = 100 km/ha = −4.5 m/s²v = 0
t = s
2.KinematicsHard
A ball is thrown straight up at 14 m/s from the edge of a roof 15 m above the ground. Ignore air resistance and use g = 9.81 m/s². Find the greatest height hmax above the ground.
v₀ = 14 m/sh₀ = 15 mg = 9.81 m/s²
hmax = m
3.Newton’s lawsMedium
Masses of 10 kg and 4.5 kg hang on either side of a light, frictionless pulley, connected by a light string. The system is released from rest. Use g = 9.81 m/s². Find the acceleration a of the masses.
m1 = 10 kgm2 = 4.5 kgg = 9.81 m/s²
a = m/s²
4.Newton’s lawsHard
A 9 kg block on a horizontal table is connected by a light string over a frictionless pulley to a hanging 4.5 kg mass. The coefficient of kinetic friction between block and table is 0.25. Use g = 9.81 m/s². Find the acceleration a of the system.
m1 = 9 kgm2 = 4.5 kgμ = 0.25g = 9.81 m/s²
a = m/s²
5.Projectile motionMedium
A ball is kicked from level ground at 16 m/s and 25° above the horizontal towards a wall 16 m away. Ignore air resistance and use g = 9.81 m/s². At what height y does the ball pass the wall?
v₀ = 16 m/sθ = 25°x = 16 mg = 9.81 m/s²
y = m
6.Projectile motionHard
A ball is launched at 20° above horizontal from the top of a 5 m cliff. Ignore air resistance. Find the time of flight t until the ball hits the ground.
v0 = 19 m/sθ = 20°h = 5 mg = 9.81 m/s²
t = s
7.Work & energyMedium
A block slides from rest down a slope at 35° to the horizontal. The coefficient of kinetic friction is 0.15. Find its speed v after it has slid 13 m along the slope.
θ = 35°μ = 0.15d = 13 mg = 9.81 m/s²
v = m/s
8.Work & energyHard
A 4 kg block is released from rest at height 2.5 m on a smooth ramp. At the bottom it crosses a rough horizontal strip 1.5 m long (μ = 0.2) and then runs onto a spring (k = 4000 N/m) on a smooth surface. Find the speed v of the block when it reaches the spring.
m = 4 kgh = 2.5 mL = 1.5 mμ = 0.2k = 4000 N/mg = 9.81 m/s²
v = m/s
9.Momentum & collisionsMedium
A 0.5 kg glider moving at 11 m/s makes a perfectly elastic head-on collision with a 3.5 kg glider at rest on a frictionless track. Find the velocity v′2 of the second glider after the collision.
m1 = 0.5 kgm2 = 3.5 kgv1 = 11 m/sv2 = 0
v′2 = m/s
10.Momentum & collisionsHard
A 0.25 kg ball hits a wall at 18 m/s and bounces straight back at 17 m/s. The contact lasts 50 ms. Find the magnitude of the impulse J the wall gives the ball.
m = 0.25 kgvin = 18 m/svout = 17 m/sΔt = 50 ms
J = N·s
11.Hydrostatic forceMedium
A vertical rectangular gate 1 m wide sits in the wall of a tank of water, with its top edge 2.5 m below the surface. Find the resultant hydrostatic force F on the gate.
A vertical rectangular gate 1.5 m wide sits in the wall of a tank of glycerin, with its top edge 2.5 m below the surface. Find the depth ycp of the centre of pressure below the surface.
Water flows through a horizontal venturi meter with an inlet diameter of 100 mm and a throat diameter of 60 mm. The pressure at the inlet is 40 kPa higher than at the throat. Ignoring losses, find the flow rate Q.
A horizontal venturi meter (inlet 200 mm, throat 150 mm) carries water. A mercury U-tube manometer connected between the inlet and the throat shows a level difference of 70 mm. The discharge coefficient is 0.96. Find the flow rate Q. Use ρ = 1000 kg/m³ for water, 13 600 kg/m³ for mercury and g = 9.81 m/s².
A heat engine receives heat from a source at 700 °C and rejects heat to the surroundings at 20 °C. Its actual thermal efficiency is 35%. Find its second-law efficiency ηII, the ratio of the actual efficiency to the Carnot efficiency.
TH = 700 °CTL = 20 °Cη = 35%
ηII = %
18.Heat engines & refrigeratorsHard
A heat pump delivers 5.5 kW of heat to a heating system at 20 °C, taking heat from a source at -5 °C. Its actual COP is 50% of the Carnot COP between these temperatures. Find the electrical power Ẇ it uses.
TH = 20 °CTL = -5 °CηII = 50%Q̇H = 5.5 kW
Ẇ = kW
19.Waves, sound & opticsMedium
An object stands 40 cm in front of a thin converging lens with a focal length of 25 cm. Find the magnification m (negative for an inverted image).
do = 40 cmf = 25 cm
m =
20.Waves, sound & opticsHard
Two slits 0.25 mm apart are lit with monochromatic light. On a screen 3 m away, bright fringe number 1 lies 6.384 mm from the central fringe. Find the wavelength λ.
d = 0.25 mmL = 3 my1 = 6.384 mmm = 1
λ = nm
3Solutions
1.Kinematics
Answer: t = 6.173 s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Units
v₀ = 100/3.6 = 27.78 m/s
Braking time
0 = v₀ − a·t → t = v₀/a = 27.78/4.5 = 6.173 s
Answer
t = 6.173 s
2.Kinematics
Answer: hmax = 24.99 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Rise above the roof
0 = v₀² − 2·g·Δh → Δh = 14²/(2·9.81) = 9.99 m
Height above the ground
hmax = 15 + 9.99 = 24.99 m
Answer
hmax = 24.99 m
3.Newton’s laws
Answer: a = 3.721 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Acceleration
The net driving force is the difference of the weights; it moves the total mass.
a = (10 − 4.5)·9.81/(10 + 4.5) = 3.721 m/s²
Answer
a = 3.721 m/s²
4.Newton’s laws
Answer: a = 1.635 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Time to the wall
vx = 16·cos 25° = 14.5 m/s
t = x/vx = 16/14.5 = 1.103 s
Height at that time
y = 6.762·1.103 − ½·9.81·1.103² = 1.489 m
Answer
y = 1.489 m
The ball is already on its way down at the wall.
6.Projectile motion
Answer: t = 1.87 s
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 19·cos 20° = 17.85 m/s
vy = v0·sin θ = 19·sin 20° = 6.498 m/s
Time in the air
Solve y(t) = h + vy·t − ½gt² = 0 for the positive root.
0 = 5 + 6.498·t − 4.905·t²
t = (vy + √(vy² + 2gh))/g = (6.498 + √(42.23 + 98.1))/9.81 = 1.87 s
Answer
t = 1.87 s
7.Work & energy
Answer: v = 10.72 m/s
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy balance along the slope
The block drops a height d·sin θ while friction removes μmg·cos θ·d. The mass cancels.
½v² = g·d·(sin θ − μ·cos θ)
v = √(2·9.81·13·(0.5736 − 0.15·0.8192)) = 10.72 m/s
Answer
v = 10.72 m/s
8.Work & energy
Answer: v = 6.57 m/s
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy left after the rough strip
The ramp is smooth, so only the strip removes energy.
mgh − μmgL = 39.24·(2.5 − 0.2·1.5) = 86.33 J
Speed at the spring
½mv² = mg(h − μL) → v = √(2g(h − μL)) = √(2·9.81·2.2) = 6.57 m/s
Answer
v = 6.57 m/s
9.Momentum & collisions
Answer: v′2 = 2.75 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Elastic collision with a target at rest
Solving momentum and energy conservation together gives these two results.
v′1 = (0.5 − 3.5)/(0.5 + 3.5)·11 = −8.25 m/s
v′2 = 2·0.5/(0.5 + 3.5)·11 = 2.75 m/s
Answer
v′2 = 2.75 m/s
10.Momentum & collisions
Answer: J = 8.75 N·s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Change in momentum
J = m·Δv = 0.25·(17 + 18) = 8.75 N·s
Answer
J = 8.75 N·s
11.Hydrostatic force
Answer: F = 47.82 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 2.5 + 1.5/2 = 3.25 m
A = H·b = 1.5·1 = 1.5 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·3.25·1.5 = 47.82 kN
Answer
F = 47.82 kN
12.Hydrostatic force
Answer: ycp = 3.308 m
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 2.5 + 1.5/2 = 3.25 m
A = H·b = 1.5·1.5 = 2.25 m²
Resultant force
F = ρ·g·yc·A = 1260·9.81·3.25·2.25 = 90.39 kN
Centre of pressure
Pressure grows with depth, so the resultant acts below the centroid.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Continuity
v1 = v2·(60/100)² = 0.36·v2
Bernoulli between inlet and throat
The pipe is horizontal, so only pressure and velocity change.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Pressure difference from the manometer
Δp = (13600 − 1000)·9.81·0.07 = 8652 Pa
Throat velocity
Continuity and Bernoulli together give the ideal throat velocity.
Combined gas law: for a fixed amount of ideal gas, P1V1/T1 = P2V2/T2.
Absolute temperatures
T1 = 308.1 K, T2 = 443.1 K
Combined gas law
V2 = V1·(P1/P2)·(T2/T1) = 20·(250/300)·(443.1/308.1) = 23.97 L
Answer
V2 = 23.97 L
17.Heat engines & refrigerators
Answer: ηII = 50.09 %
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 700 + 273.15 = 973.1 K
TL = 20 + 273.15 = 293.1 K
Carnot efficiency
ηCarnot = 1 − 293.1/973.1 = 69.88 %
Second-law efficiency
ηII = η/ηCarnot = 35/69.88 = 50.09 %
Answer
ηII = 50.09 %
18.Heat engines & refrigerators
Answer: Ẇ = 0.9381 kW
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 20 + 273.15 = 293.1 K
TL = -5 + 273.15 = 268.1 K
Carnot and actual COP
COPmax = 293.1/(293.1 − 268.1) = 11.73
COP = 0.5·11.73 = 5.863
Power input
Ẇ = Q̇H/COP = 5.5/5.863 = 0.9381 kW
Answer
Ẇ = 0.9381 kW
19.Waves, sound & optics
Answer: m = −1.667
Geometric optics: at a boundary, n₁·sin θ₁ = n₂·sin θ₂ (Snell's law), with angles measured from the normal and n = c/v. Going into a slower medium the ray bends towards the normal. From a denser medium (n₁ > n₂) beyond the critical angle θc = arcsin(n₂/n₁) all light is reflected: total internal reflection. Thin lenses and spherical mirrors obey 1/f = 1/do + 1/di with the magnification m = −di/do. Sign convention: f > 0 for a converging lens and a concave mirror (f = R/2), f < 0 for a diverging lens and a convex mirror; di > 0 for a real image, di < 0 for a virtual one, and m < 0 for an inverted image.
Thin-lens equation
1/di = 1/f − 1/do = 1/25 − 1/40
di = 66.67 cm
Magnification
m = −di/do = −66.67/40 = −1.667
Answer
m = −1.667
20.Waves, sound & optics
Answer: λ = 532 nm
Interference and diffraction: light from two slits a distance d apart reaches a point on the screen with a path difference d·sin θ. Bright fringes appear where d·sin θ = mλ (m = 0, ±1, ±2, …). For a screen at distance L ≫ d, the m-th bright fringe is at y = mλL/d and the fringe spacing is Δy = λL/d. A grating with N lines per millimetre has d = 1/N and sharp maxima at d·sin θ = mλ; since sin θ ≤ 1, the highest order is the largest whole number m ≤ d/λ. A single slit of width a has dark fringes at a·sin θ = mλ, m = ±1, ±2, …