Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A car driving at 50 km/h brakes with a constant deceleration of 4.5 m/s² until it stops. Find the braking distance s.
v₀ = 50 km/ha = −4.5 m/s²v = 0
s = m
2.KinematicsHard
A tram starts from rest and accelerates at 2 m/s² for 9 s, then runs at constant speed for 22 s, and finally brakes at 2 m/s² until it stops. Find the total distance s between the two stops.
a1 = 2 m/s²t1 = 9 st2 = 22 sa3 = −2 m/s²
s = m
3.Newton’s lawsMedium
A 19 kg block slides down a slope at 45° to the horizontal. The coefficient of kinetic friction is 0.2. Use g = 9.81 m/s². Find the acceleration a of the block along the slope.
m = 19 kgθ = 45°μ = 0.2g = 9.81 m/s²
a = m/s²
4.Newton’s lawsHard
A 4 kg block on a horizontal table is connected by a light string over a frictionless pulley to a hanging 5.5 kg mass. The coefficient of kinetic friction between block and table is 0.1. Use g = 9.81 m/s². Find the tension T in the string.
m1 = 4 kgm2 = 5.5 kgμ = 0.1g = 9.81 m/s²
T = N
5.Projectile motionMedium
A ball is launched from level ground at 25° above the horizontal and lands 25 m away. Ignore air resistance and use g = 9.81 m/s². Find the launch speed v0.
θ = 25°R = 25 mg = 9.81 m/s²
v0 = m/s
6.Projectile motionHard
A ball is launched at 55° above horizontal from the top of a 45 m cliff. Ignore air resistance. Find the horizontal distance x travelled before the ball hits the ground.
v0 = 33 m/sθ = 55°h = 45 mg = 9.81 m/s²
x = m
7.Work & energyMedium
A 10 kg ball hangs on a light string of length 1 m. It is pulled aside until the string makes 50° with the vertical and released from rest. Find the tension T in the string when the ball passes the lowest point.
m = 10 kgL = 1 mθ = 50°g = 9.81 m/s²
T = N
8.Work & energyHard
A 0.5 kg block is released from rest at height 5 m on a smooth ramp. At the bottom it crosses a rough horizontal strip 3 m long (μ = 0.2) and then runs onto a spring (k = 5000 N/m) on a smooth surface. Find the speed v of the block when it reaches the spring.
m = 0.5 kgh = 5 mL = 3 mμ = 0.2k = 5000 N/mg = 9.81 m/s²
v = m/s
9.Momentum & collisionsMedium
A 5 g bullet is fired horizontally into a 3.5 kg wooden block hanging on light strings, and stays inside it. The block swings up until it is 8 cm higher than at the start. Use g = 9.81 m/s². Find the speed v of the bullet before impact.
m = 5 gM = 3.5 kgh = 8 cmg = 9.81 m/s²
v = m/s
10.Momentum & collisionsHard
A 0.5 kg ball hits a wall at 9 m/s and bounces straight back at 19 m/s. The contact lasts 10 ms. Find the magnitude of the impulse J the wall gives the ball.
m = 0.5 kgvin = 9 m/svout = 19 m/sΔt = 10 ms
J = N·s
11.Hydrostatic forceMedium
A vertical rectangular gate 3 m wide sits in the wall of a tank of water, with its top edge 1.5 m below the surface. Find the resultant hydrostatic force F on the gate.
A vertical rectangular gate 2 m wide sits in the wall of a tank of water, with its top edge 1 m below the surface. Find the resultant hydrostatic force F on the gate.
Water flows through a horizontal venturi meter with an inlet diameter of 150 mm and a throat diameter of 75 mm. The pressure at the inlet is 39 kPa higher than at the throat. Ignoring losses, find the flow rate Q.
Water flows up through a pipe that narrows from 200 mm to 75 mm while rising 6 m. At section 1 the pressure is 100 kPa and the velocity is 0.75 m/s. Ignoring losses, find the pressure p2 at section 2.
A heat engine receives heat from a source at 650 °C and rejects heat to the surroundings at 25 °C. Its actual thermal efficiency is 37%. Find its second-law efficiency ηII, the ratio of the actual efficiency to the Carnot efficiency.
TH = 650 °CTL = 25 °Cη = 37%
ηII = %
18.Heat engines & refrigeratorsHard
A refrigerator keeps its cold space at -20 °C in a kitchen at 30 °C, removing heat from the cold space at 3 kW. Find the minimum power input Ẇmin.
TH = 30 °CTL = -20 °CQ̇L = 3 kW
Ẇmin = kW
19.Waves, sound & opticsMedium
Light inside a transparent block is totally reflected at the boundary with water (n = 1.33) for every angle of incidence above 48.8°. Find the refractive index n1 of the block.
θc = 48.8°n2 = 1.33
n1 =
20.Waves, sound & opticsHard
Light of wavelength 550 nm falls on two slits 0.5 mm apart. The screen is 1.2 m away. Find the distance y5 from the central bright fringe to bright fringe number 5.
λ = 550 nmd = 0.5 mmL = 1.2 mm = 5
y5 = mm
3Solutions
1.Kinematics
Answer: s = 21.43 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Units
v₀ = 50/3.6 = 13.89 m/s
Braking distance
0 = v₀² − 2·a·s → s = v₀²/(2a) = 13.89²/(2·4.5) = 21.43 m
Answer
s = 21.43 m
2.Kinematics
Answer: s = 558 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Top speed
v = a1·t1 = 2·9 = 18 m/s
Distance of each phase
s1 = ½·2·9² = 81 m
s2 = 18·22 = 396 m
s3 = 18²/(2·2) = 81 m
Total distance
s = 81 + 396 + 81 = 558 m
Answer
s = 558 m
3.Newton’s laws
Answer: a = 5.549 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Solve the range formula for v₀
v₀ = √(g·R/sin 2θ) = √(9.81·25/sin 50°) = 17.89 m/s
Answer
v0 = 17.89 m/s
6.Projectile motion
Answer: x = 129.7 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 33·cos 55° = 18.93 m/s
vy = v0·sin θ = 33·sin 55° = 27.03 m/s
Time in the air
Solve y(t) = h + vy·t − ½gt² = 0 for the positive root.
0 = 45 + 27.03·t − 4.905·t²
t = (vy + √(vy² + 2gh))/g = (27.03 + √(730.7 + 882.9))/9.81 = 6.85 s
Horizontal distance
x = vx·t = 18.93·6.85 = 129.7 m
Answer
x = 129.7 m
7.Work & energy
Answer: T = 168.2 N
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d). On a circular path the net force towards the centre must equal mv²/r.
Speed at the bottom
v² = 2gL(1 − cos θ) = 2·9.81·1·(1 − cos 50°) = 7.009 m²/s²
Forces at the bottom
m·g = 10·9.81 = 98.1 N
T = mg + mv²/L = 98.1 + 10·7.009/1 = 168.2 N
Answer
T = 168.2 N
Check: T = mg(3 − 2cos θ) = 168.2 N.
8.Work & energy
Answer: v = 9.291 m/s
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy left after the rough strip
The ramp is smooth, so only the strip removes energy.
mgh − μmgL = 4.905·(5 − 0.2·3) = 21.58 J
Speed at the spring
½mv² = mg(h − μL) → v = √(2g(h − μL)) = √(2·9.81·4.4) = 9.291 m/s
Answer
v = 9.291 m/s
9.Momentum & collisions
Answer: v = 878.2 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Swing after impact
V = √(2·g·h) = √(2·9.81·0.08) = 1.253 m/s
Collision
m·v = (m + M)·V → v = (0.005 + 3.5)·1.253/0.005 = 878.2 m/s
Answer
v = 878.2 m/s
10.Momentum & collisions
Answer: J = 14 N·s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Change in momentum
J = m·Δv = 0.5·(19 + 9) = 14 N·s
Answer
J = 14 N·s
11.Hydrostatic force
Answer: F = 147.2 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 1.5 + 2/2 = 2.5 m
A = H·b = 2·3 = 6 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·2.5·6 = 147.2 kN
Answer
F = 147.2 kN
12.Hydrostatic force
Answer: F = 51.5 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 1 + 1.5/2 = 1.75 m
A = H·b = 1.5·2 = 3 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·1.75·3 = 51.5 kN
Answer
F = 51.5 kN
13.Continuity & Bernoulli
Answer: Q = 40.3 L/s
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Continuity
v1 = v2·(75/150)² = 0.25·v2
Bernoulli between inlet and throat
The pipe is horizontal, so only pressure and velocity change.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 650 + 273.15 = 923.1 K
TL = 25 + 273.15 = 298.1 K
Carnot efficiency
ηCarnot = 1 − 298.1/923.1 = 67.7 %
Second-law efficiency
ηII = η/ηCarnot = 37/67.7 = 54.65 %
Answer
ηII = 54.65 %
18.Heat engines & refrigerators
Answer: Ẇmin = 0.5925 kW
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
The least work is needed by a reversible machine, which has the highest COP.
Ẇmin = Q̇L/COP = 3/5.063 = 0.5925 kW
Answer
Ẇmin = 0.5925 kW
19.Waves, sound & optics
Answer: n1 = 1.768
Geometric optics: at a boundary, n₁·sin θ₁ = n₂·sin θ₂ (Snell's law), with angles measured from the normal and n = c/v. Going into a slower medium the ray bends towards the normal. From a denser medium (n₁ > n₂) beyond the critical angle θc = arcsin(n₂/n₁) all light is reflected: total internal reflection. Thin lenses and spherical mirrors obey 1/f = 1/do + 1/di with the magnification m = −di/do. Sign convention: f > 0 for a converging lens and a concave mirror (f = R/2), f < 0 for a diverging lens and a convex mirror; di > 0 for a real image, di < 0 for a virtual one, and m < 0 for an inverted image.
Refractive index of the block
n₁ = n₂/sin θc = 1.33/0.7524 = 1.768
Answer
n1 = 1.768
20.Waves, sound & optics
Answer: y5 = 6.6 mm
Interference and diffraction: light from two slits a distance d apart reaches a point on the screen with a path difference d·sin θ. Bright fringes appear where d·sin θ = mλ (m = 0, ±1, ±2, …). For a screen at distance L ≫ d, the m-th bright fringe is at y = mλL/d and the fringe spacing is Δy = λL/d. A grating with N lines per millimetre has d = 1/N and sharp maxima at d·sin θ = mλ; since sin θ ≤ 1, the highest order is the largest whole number m ≤ d/λ. A single slit of width a has dark fringes at a·sin θ = mλ, m = ±1, ±2, …