Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A car driving at 90 km/h brakes with a constant deceleration of 6 m/s² until it stops. Find the braking distance s.
v₀ = 90 km/ha = −6 m/s²v = 0
s = m
2.KinematicsHard
A model rocket is launched straight up from rest. Its engine gives it a constant upward acceleration of 22 m/s² for 3 s, after which the engine stops and the rocket moves freely. Ignore air resistance and use g = 9.81 m/s². Find the greatest height hmax the rocket reaches.
a = 22 m/s²t1 = 3 sg = 9.81 m/s²
hmax = m
3.Newton’s lawsMedium
Masses of 6 kg and 2.5 kg hang on either side of a light, frictionless pulley, connected by a light string. The system is released from rest. Use g = 9.81 m/s². Find the acceleration a of the masses.
m1 = 6 kgm2 = 2.5 kgg = 9.81 m/s²
a = m/s²
4.Newton’s lawsHard
A block is given a push so that it starts sliding up a ramp at 30° with a speed of 7.5 m/s. The coefficient of kinetic friction is 0.1. Use g = 9.81 m/s². How far d along the ramp does it slide before it stops?
v₀ = 7.5 m/sθ = 30°μ = 0.1g = 9.81 m/s²
d = m
5.Projectile motionMedium
A ball is launched at 70° above horizontal from level ground. Ignore air resistance. Find the time of flight t until the ball hits the ground.
v0 = 24 m/sθ = 70°g = 9.81 m/s²
t = s
6.Projectile motionHard
A ball is thrown from ground level at 32 m/s and 30° above the horizontal. It lands on the flat roof of a building 5 m high, on its way down. Ignore air resistance and use g = 9.81 m/s². Find the horizontal distance x from the launch point to where it lands.
v₀ = 32 m/sθ = 30°hroof = 5 mg = 9.81 m/s²
x = m
7.Work & energyMedium
A car travelling at 110 km/h on a level road brakes hard and skids to a stop with its wheels locked. The coefficient of kinetic friction between the tyres and the road is 0.4. Find the stopping distance d.
v = 110 km/hμ = 0.4g = 9.81 m/s²
d = m
8.Work & energyHard
A 2.5 kg block is released from rest at height 5 m on a smooth ramp. At the bottom it crosses a rough horizontal strip 1.5 m long (μ = 0.25) and then runs onto a spring (k = 4000 N/m) on a smooth surface. Find the maximum compression x of the spring.
m = 2.5 kgh = 5 mL = 1.5 mμ = 0.25k = 4000 N/mg = 9.81 m/s²
x = cm
9.Momentum & collisionsMedium
A 600 kg car moving at 17 m/s runs into a stationary 900 kg car and the two lock together. How much kinetic energy ΔK is lost in the collision?
m1 = 600 kgv1 = 17 m/sm2 = 900 kgv2 = 0
ΔK = J
10.Momentum & collisionsHard
At a crossing a 2000 kg car travelling east at 18 m/s collides with a 1800 kg car travelling north at 15 m/s. The cars lock together. Find the speed v′ of the wreck just after the collision.
m1 = 2000 kgv1 = 18 m/s (E)m2 = 1800 kgv2 = 15 m/s (N)
v′ = m/s
11.Hydrostatic forceMedium
A vertical rectangular gate 3 m wide sits in the wall of a tank of water, with its top edge 1.5 m below the surface. Find the resultant hydrostatic force F on the gate.
A vertical rectangular gate 1 m wide sits in the wall of a tank of glycerin, with its top edge 2.5 m below the surface. Find the depth ycp of the centre of pressure below the surface.
Water flows through a horizontal venturi meter with an inlet diameter of 300 mm and a throat diameter of 150 mm. The pressure at the inlet is 53 kPa higher than at the throat. Ignoring losses, find the flow rate Q.
Water flows up through a pipe that narrows from 100 mm to 75 mm while rising 3 m. At section 1 the pressure is 170 kPa and the velocity is 2.75 m/s. Ignoring losses, find the pressure p2 at section 2.
A reversible (Carnot) heat engine takes in 3500 kJ of heat from a reservoir at 425 °C and rejects 1620 kJ per cycle. Find the temperature TL of the cold reservoir in °C.
TH = 425 °CQH = 3500 kJQL = 1620 kJ
TL = °C
18.Heat engines & refrigeratorsHard
A heat pump keeps a house at 20 °C while it is -5 °C outside, delivering 9 kW of heat to the house. Find the minimum power input Ẇmin.
TH = 20 °CTL = -5 °CQ̇H = 9 kW
Ẇmin = kW
19.Waves, sound & opticsMedium
A pipe closed at one end is 0.8 m long. The speed of sound is 343 m/s. Find the frequency f5 of its harmonic number 5.
v = 343 m/sn = 5L = 0.8 m
f5 = Hz
20.Waves, sound & opticsHard
A parking sensor at rest sends ultrasound of 30 kHz towards a car that moves away at 10 m/s. Find the frequency f″ of the echo received back at the sensor (speed of sound 343 m/s).
f = 30 kHzu = 10 m/sv = 343 m/s
f″ = Hz
3Solutions
1.Kinematics
Answer: s = 52.08 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Units
v₀ = 90/3.6 = 25 m/s
Braking distance
0 = v₀² − 2·a·s → s = v₀²/(2a) = 25²/(2·6) = 52.08 m
Answer
s = 52.08 m
2.Kinematics
Answer: hmax = 321 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Powered phase
v₁ = 22·3 = 66 m/s
h₁ = ½·22·3² = 99 m
Free flight up
At the top the velocity is zero.
Δh = v₁²/(2g) = 66²/(2·9.81) = 222 m
hmax = 99 + 222 = 321 m
Answer
hmax = 321 m
3.Newton’s laws
Answer: a = 4.039 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Acceleration
The net driving force is the difference of the weights; it moves the total mass.
a = (6 − 2.5)·9.81/(6 + 2.5) = 4.039 m/s²
Answer
a = 4.039 m/s²
4.Newton’s laws
Answer: d = 4.887 m
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Deceleration
Both forces point down the slope; the mass cancels.
a = 9.81·(sin 30° + 0.1·cos 30°) = 5.755 m/s²
Distance
d = v₀²/(2a) = 7.5²/(2·5.755) = 4.887 m
Answer
d = 4.887 m
5.Projectile motion
Answer: t = 4.598 s
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 24·cos 70° = 8.208 m/s
vy = v0·sin θ = 24·sin 70° = 22.55 m/s
Time in the air
Starting and landing at the same height: t = 2vy/g.
t = 2·22.55/9.81 = 4.598 s
Answer
t = 4.598 s
6.Projectile motion
Answer: x = 80.7 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
vx = 27.71 m/s, vy = 16 m/s
Time to land on the roof
Larger root: the ball is descending.
5 = 16·t − 4.905·t²
t = (16 + √(16² − 2·9.81·5))/9.81 = 2.912 s
Horizontal distance
x = vx·t = 27.71·2.912 = 80.7 m
Answer
x = 80.7 m
7.Work & energy
Answer: d = 119 m
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Speed in base units
v = 110/3.6 = 30.56 m/s
Energy balance
½mv² = μmg·d → d = v²/(2μg) = 30.56²/(2·0.4·9.81) = 119 m
Answer
d = 119 m
Doubling the speed makes the stopping distance four times longer.
8.Work & energy
Answer: x = 23.81 cm
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy left after the rough strip
The ramp is smooth, so only the strip removes energy.
mgh − μmgL = 24.53·(5 − 0.25·1.5) = 113.4 J
Maximum compression
½kx² = 113.4 → x = √(2·113.4/4000) = 0.2381 m = 23.81 cm
Answer
x = 23.81 cm
9.Momentum & collisions
Answer: ΔK = 52020 J
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Common velocity
v′ = m1·v1/(m1 + m2) = 600·17/1500 = 6.8 m/s
Kinetic energy before and after
Kbefore = ½·600·17² = 86700 J
Kafter = ½·1500·6.8² = 34680 J
Energy lost
ΔK = 86700 − 34680 = 52020 J
Answer
ΔK = 52020 J
The lost energy goes into deformation, heat and sound.
10.Momentum & collisions
Answer: v′ = 11.84 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Continuity
v1 = v2·(150/300)² = 0.25·v2
Bernoulli between inlet and throat
The pipe is horizontal, so only pressure and velocity change.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Combined gas law: for a fixed amount of ideal gas, P1V1/T1 = P2V2/T2.
Absolute temperatures
T1 = 303.1 K, T2 = 523.1 K
Combined gas law
V2 = V1·(P1/P2)·(T2/T1) = 2·(250/800)·(523.1/303.1) = 1.079 L
Answer
V2 = 1.079 L
17.Heat engines & refrigerators
Answer: TL = 49.99 °C
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperature of the source
TH = 425 + 273.15 = 698.1 K
Reversible heat ratio
TL = TH·QL/QH = 698.1·1620/3500 = 323.1 K = 49.99 °C
Answer
TL = 49.99 °C
18.Heat engines & refrigerators
Answer: Ẇmin = 0.7675 kW
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
The least work is needed by a reversible machine, which has the highest COP.
Ẇmin = Q̇H/COP = 9/11.73 = 0.7675 kW
Answer
Ẇmin = 0.7675 kW
19.Waves, sound & optics
Answer: f5 = 535.9 Hz
Standing waves and the Doppler effect: a string fixed at both ends, or a pipe open at both ends, fits whole half-wavelengths: L = nλ/2, fn = n·v/(2L), n = 1, 2, 3, … A pipe closed at one end has a node at the closed end and an antinode at the open end: L = nλ/4 with odd n only, fn = n·v/(4L). When source or observer move along the line between them, f′ = f·(v ± vo)/(v ∓ vs): use the upper signs for motion towards each other. Two waves of nearly equal frequency beat at |f₁ − f₂|.
Wavelength of this mode
λ = 4L/n = 4·0.8/5 = 0.64 m
Frequency
f = v/λ = 343/0.64 = 535.9 Hz
Answer
f5 = 535.9 Hz
20.Waves, sound & optics
Answer: f″ = 28300 Hz
Standing waves and the Doppler effect: a string fixed at both ends, or a pipe open at both ends, fits whole half-wavelengths: L = nλ/2, fn = n·v/(2L), n = 1, 2, 3, … A pipe closed at one end has a node at the closed end and an antinode at the open end: L = nλ/4 with odd n only, fn = n·v/(4L). When source or observer move along the line between them, f′ = f·(v ± vo)/(v ∓ vs): use the upper signs for motion towards each other. Two waves of nearly equal frequency beat at |f₁ − f₂|.