Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A plane starts from rest and accelerates uniformly at 4 m/s² along a runway. Find its speed v after 700 m.
v₀ = 0a = 4 m/s²s = 700 m
v = m/s
2.KinematicsHard
A ball is thrown straight up at 6 m/s from the edge of a roof 5 m above the ground. Ignore air resistance and use g = 9.81 m/s². Find the greatest height hmax above the ground.
v₀ = 6 m/sh₀ = 5 mg = 9.81 m/s²
hmax = m
3.Newton’s lawsMedium
A 20 kg box is pushed up a ramp at 30° to the horizontal at constant speed, by a force parallel to the ramp. The coefficient of kinetic friction is 0.15. Use g = 9.81 m/s². Find the pushing force F.
m = 20 kgθ = 30°μ = 0.15g = 9.81 m/s²
F = N
4.Newton’s lawsHard
A 6 kg block on a horizontal table is connected by a light string over a frictionless pulley to a hanging 4 kg mass. The coefficient of kinetic friction between block and table is 0.25. Use g = 9.81 m/s². Find the acceleration a of the system.
m1 = 6 kgm2 = 4 kgμ = 0.25g = 9.81 m/s²
a = m/s²
5.Projectile motionMedium
A ball is kicked from level ground at 26 m/s and 70° above the horizontal towards a wall 31 m away. Ignore air resistance and use g = 9.81 m/s². At what height y does the ball pass the wall?
v₀ = 26 m/sθ = 70°x = 31 mg = 9.81 m/s²
y = m
6.Projectile motionHard
A ball is thrown from ground level at 40 m/s and 50° above the horizontal. It lands on the flat roof of a building 21 m high, on its way down. Ignore air resistance and use g = 9.81 m/s². Find the horizontal distance x from the launch point to where it lands.
v₀ = 40 m/sθ = 50°hroof = 21 mg = 9.81 m/s²
x = m
7.Work & energyMedium
A block slides from rest down a slope at 20° to the horizontal. The coefficient of kinetic friction is 0.25. Find its speed v after it has slid 9 m along the slope.
θ = 20°μ = 0.25d = 9 mg = 9.81 m/s²
v = m/s
8.Work & energyHard
A 0.5 kg block is released from rest at height 3 m on a smooth ramp. At the bottom it crosses a rough horizontal strip 2 m long (μ = 0.1) and then runs onto a spring (k = 1000 N/m) on a smooth surface. Find the speed v of the block when it reaches the spring.
m = 0.5 kgh = 3 mL = 2 mμ = 0.1k = 1000 N/mg = 9.81 m/s²
v = m/s
9.Momentum & collisionsMedium
A 5 kg glider moving at 8 m/s makes a perfectly elastic head-on collision with a 0.5 kg glider at rest on a frictionless track. Find the velocity v′1 of the first glider after the collision (positive in its original direction).
m1 = 5 kgm2 = 0.5 kgv1 = 8 m/sv2 = 0
v′1 = m/s
10.Momentum & collisionsHard
At a crossing a 2000 kg car travelling east at 16 m/s collides with an 800 kg car travelling north at 16 m/s. The cars lock together. Find the direction θ of the wreck just after the collision, measured north of east.
m1 = 2000 kgv1 = 16 m/s (E)m2 = 800 kgv2 = 16 m/s (N)
θ = °
11.Hydrostatic forceMedium
A vertical rectangular gate 3 m wide sits in the wall of a tank of water, with its top edge 2 m below the surface. Find the resultant hydrostatic force F on the gate.
d = 2 mH = 3 mb = 3 mρ = 1000 kg/m³g = 9.81 m/s²
F = kN
12.Hydrostatic forceHard
A vertical rectangular gate 3 m wide sits in the wall of a tank of water, with its top edge 3 m below the surface. Find the resultant hydrostatic force F on the gate.
d = 3 mH = 3 mb = 3 mρ = 1000 kg/m³g = 9.81 m/s²
F = kN
13.Continuity & BernoulliMedium
Water flows through a horizontal venturi meter with an inlet diameter of 100 mm and a throat diameter of 60 mm. The pressure at the inlet is 31 kPa higher than at the throat. Ignoring losses, find the flow rate Q.
Water flows up through a pipe that narrows from 75 mm to 50 mm while rising 5 m. At section 1 the pressure is 220 kPa and the velocity is 1 m/s. Ignoring losses, find the pressure p2 at section 2.
A heat engine receives heat from a source at 450 °C and rejects heat to the surroundings at 10 °C. Its actual thermal efficiency is 40%. Find its second-law efficiency ηII, the ratio of the actual efficiency to the Carnot efficiency.
TH = 450 °CTL = 10 °Cη = 40%
ηII = %
18.Heat engines & refrigeratorsHard
A refrigerator keeps its cold space at -20 °C in a kitchen at 28 °C, removing heat from the cold space at 3 kW. Find the highest possible coefficient of performance COPmax.
TH = 28 °CTL = -20 °CQ̇L = 3 kW
COPmax =
19.Waves, sound & opticsMedium
An object stands 60 cm in front of a thin diverging lens with a focal length of 30 cm. Find the magnification m (negative for an inverted image).
do = 60 cmf = −30 cm
m =
20.Waves, sound & opticsHard
A sensor at rest sends ultrasound of 20 kHz towards a car that approaches at 10 m/s and mixes the echo with the emitted signal. Find the beat frequency fb (speed of sound 343 m/s).
f = 20 kHzu = 10 m/sv = 343 m/s
fb = Hz
3Solutions
1.Kinematics
Answer: v = 74.83 m/s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Speed after the distance
v = √(2·a·s) = √(2·4·700) = 74.83 m/s
Answer
v = 74.83 m/s
(269.4 km/h)
2.Kinematics
Answer: hmax = 6.835 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Rise above the roof
0 = v₀² − 2·g·Δh → Δh = 6²/(2·9.81) = 1.835 m
Height above the ground
hmax = 5 + 1.835 = 6.835 m
Answer
hmax = 6.835 m
3.Newton’s laws
Answer: F = 123.6 N
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Forces along the slope
Constant speed: the forces balance.
F = m·g·sin θ + μ·m·g·cos θ
Pushing force
F = 98.1 + 25.49 = 123.6 N
Answer
F = 123.6 N
4.Newton’s laws
Answer: a = 2.453 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Time to the wall
vx = 26·cos 70° = 8.893 m/s
t = x/vx = 31/8.893 = 3.486 s
Height at that time
y = 24.43·3.486 − ½·9.81·3.486² = 25.56 m
Answer
y = 25.56 m
The ball is already on its way down at the wall.
6.Projectile motion
Answer: x = 140.5 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
vx = 25.71 m/s, vy = 30.64 m/s
Time to land on the roof
Larger root: the ball is descending.
21 = 30.64·t − 4.905·t²
t = (30.64 + √(30.64² − 2·9.81·21))/9.81 = 5.463 s
Horizontal distance
x = vx·t = 25.71·5.463 = 140.5 m
Answer
x = 140.5 m
7.Work & energy
Answer: v = 4.349 m/s
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy balance along the slope
The block drops a height d·sin θ while friction removes μmg·cos θ·d. The mass cancels.
½v² = g·d·(sin θ − μ·cos θ)
v = √(2·9.81·9·(0.342 − 0.25·0.9397)) = 4.349 m/s
Answer
v = 4.349 m/s
8.Work & energy
Answer: v = 7.412 m/s
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy left after the rough strip
The ramp is smooth, so only the strip removes energy.
mgh − μmgL = 4.905·(3 − 0.1·2) = 13.73 J
Speed at the spring
½mv² = mg(h − μL) → v = √(2g(h − μL)) = √(2·9.81·2.8) = 7.412 m/s
Answer
v = 7.412 m/s
9.Momentum & collisions
Answer: v′1 = 6.545 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Elastic collision with a target at rest
Solving momentum and energy conservation together gives these two results.
v′1 = (5 − 0.5)/(5 + 0.5)·8 = 6.545 m/s
v′2 = 2·5/(5 + 0.5)·8 = 14.55 m/s
Answer
v′1 = 6.545 m/s
10.Momentum & collisions
Answer: θ = 21.8 °
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Momentum components
px = 2000·16 = 32000 kg·m/s
py = 800·16 = 12800 kg·m/s
Direction
tan θ = py/px = 0.4 → θ = 21.8°
Answer
θ = 21.8°
11.Hydrostatic force
Answer: F = 309 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 2 + 3/2 = 3.5 m
A = H·b = 3·3 = 9 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·3.5·9 = 309 kN
Answer
F = 309 kN
12.Hydrostatic force
Answer: F = 397.3 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 3 + 3/2 = 4.5 m
A = H·b = 3·3 = 9 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·4.5·9 = 397.3 kN
Answer
F = 397.3 kN
13.Continuity & Bernoulli
Answer: Q = 23.86 L/s
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Continuity
v1 = v2·(60/100)² = 0.36·v2
Bernoulli between inlet and throat
The pipe is horizontal, so only pressure and velocity change.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 450 + 273.15 = 723.1 K
TL = 10 + 273.15 = 283.1 K
Carnot efficiency
ηCarnot = 1 − 283.1/723.1 = 60.84 %
Second-law efficiency
ηII = η/ηCarnot = 40/60.84 = 65.74 %
Answer
ηII = 65.74 %
18.Heat engines & refrigerators
Answer: COPmax = 5.274
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Geometric optics: at a boundary, n₁·sin θ₁ = n₂·sin θ₂ (Snell's law), with angles measured from the normal and n = c/v. Going into a slower medium the ray bends towards the normal. From a denser medium (n₁ > n₂) beyond the critical angle θc = arcsin(n₂/n₁) all light is reflected: total internal reflection. Thin lenses and spherical mirrors obey 1/f = 1/do + 1/di with the magnification m = −di/do. Sign convention: f > 0 for a converging lens and a concave mirror (f = R/2), f < 0 for a diverging lens and a convex mirror; di > 0 for a real image, di < 0 for a virtual one, and m < 0 for an inverted image.
Thin-lens equation
1/di = 1/f − 1/do = 1/(−30) − 1/60
di = −20 cm
Magnification
m = −di/do = −(−20)/60 = 0.3333
Answer
m = 0.3333
20.Waves, sound & optics
Answer: fb = 1201 Hz
Standing waves and the Doppler effect: a string fixed at both ends, or a pipe open at both ends, fits whole half-wavelengths: L = nλ/2, fn = n·v/(2L), n = 1, 2, 3, … A pipe closed at one end has a node at the closed end and an antinode at the open end: L = nλ/4 with odd n only, fn = n·v/(4L). When source or observer move along the line between them, f′ = f·(v ± vo)/(v ∓ vs): use the upper signs for motion towards each other. Two waves of nearly equal frequency beat at |f₁ − f₂|.