Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A car driving at 50 km/h brakes with a constant deceleration of 4 m/s² until it stops. Find the braking distance s.
v₀ = 50 km/ha = −4 m/s²v = 0
s = m
2.KinematicsHard
A ball is thrown straight up at 16 m/s from the edge of a roof 35 m above the ground. Ignore air resistance and use g = 9.81 m/s². Find the greatest height hmax above the ground.
v₀ = 16 m/sh₀ = 35 mg = 9.81 m/s²
hmax = m
3.Newton’s lawsMedium
A 6 kg block slides down a frictionless slope at 20° to the horizontal. Use g = 9.81 m/s². Find the acceleration a of the block along the slope.
m = 6 kgθ = 20°μ = 0g = 9.81 m/s²
a = m/s²
4.Newton’s lawsHard
A 9 kg block on a horizontal table is connected by a light string over a frictionless pulley to a hanging 3.5 kg mass. The coefficient of kinetic friction between block and table is 0.1. Use g = 9.81 m/s². Find the acceleration a of the system.
m1 = 9 kgm2 = 3.5 kgμ = 0.1g = 9.81 m/s²
a = m/s²
5.Projectile motionMedium
A ball is launched at 70° above horizontal from level ground. Ignore air resistance. Find the maximum height H the ball reaches.
v0 = 28 m/sθ = 70°g = 9.81 m/s²
H = m
6.Projectile motionHard
A ball is launched at 55° above horizontal from the top of a 20 m cliff. Ignore air resistance. Find the horizontal distance x travelled before the ball hits the ground.
v0 = 12 m/sθ = 55°h = 20 mg = 9.81 m/s²
x = m
7.Work & energyMedium
A 0.5 kg block slides 11 m down a slope at 20° to the horizontal, with a coefficient of kinetic friction of 0.1. Find the work Wf done against friction.
m = 0.5 kgθ = 20°μ = 0.1d = 11 mg = 9.81 m/s²
Wf = J
8.Work & energyHard
A 2 kg cart is released from rest at a height of 4 m on a smooth track that leads into a vertical circular loop of radius 1 m. Find the normal force N the track exerts on the cart at the top of the loop.
m = 2 kgh = 4 mR = 1 mg = 9.81 m/s²
N = N
9.Momentum & collisionsMedium
A 2 kg glider moving at 5 m/s makes a perfectly elastic head-on collision with a 1.5 kg glider at rest on a frictionless track. Find the velocity v′1 of the first glider after the collision (positive in its original direction).
m1 = 2 kgm2 = 1.5 kgv1 = 5 m/sv2 = 0
v′1 = m/s
10.Momentum & collisionsHard
A 1400 kg car runs into a parked 1500 kg car. The wrecks lock together and skid 16.5 m before stopping. The coefficient of kinetic friction between tyres and road is 0.7. Use g = 9.81 m/s². Find the speed v1 of the first car just before the collision.
A vertical rectangular gate 1.5 m wide sits in the wall of a tank of water, with its top edge 2.5 m below the surface. Find the resultant hydrostatic force F on the gate.
A vertical rectangular gate 2 m wide sits in the wall of a tank of water, with its top edge 4 m below the surface. Find the depth ycp of the centre of pressure below the surface.
d = 4 mH = 2 mb = 2 mρ = 1000 kg/m³g = 9.81 m/s²
ycp = m
13.Continuity & BernoulliMedium
Water flows at 27 L/s through a horizontal pipe that narrows from 100 mm to 75 mm. The pressure in the narrow section is 290 kPa. Ignoring losses, find the pressure p1 in the wide section.
Water flows up through a pipe that narrows from 100 mm to 40 mm while rising 10 m. At section 1 the pressure is 390 kPa and the velocity is 1.5 m/s. Ignoring losses, find the pressure p2 at section 2.
A reversible (Carnot) heat engine takes in 2600 kJ of heat from a reservoir at 450 °C and rejects 1054 kJ per cycle. Find the temperature TL of the cold reservoir in °C.
TH = 450 °CQH = 2600 kJQL = 1054 kJ
TL = °C
18.Heat engines & refrigeratorsHard
A heat pump delivers 10.5 kW of heat to a heating system at 21 °C, taking heat from a source at 10 °C. Its actual COP is 35% of the Carnot COP between these temperatures. Find the electrical power Ẇ it uses.
TH = 21 °CTL = 10 °CηII = 35%Q̇H = 10.5 kW
Ẇ = kW
19.Waves, sound & opticsMedium
An object 5 cm tall stands 10 cm in front of a thin converging lens with a focal length of 15 cm. Find the image height hi (negative for an inverted image).
ho = 5 cmdo = 10 cmf = 15 cm
hi = cm
20.Waves, sound & opticsHard
Two thin lenses share an axis, 25 cm apart: lens 1 with f₁ = 12 cm and lens 2 with f₂ = 15 cm. An object stands 18 cm in front of lens 1. Find the position di2 of the final image measured from lens 2 (positive beyond lens 2, real-is-positive convention).
f1 = 12 cmf2 = 15 cms = 25 cmdo = 18 cm
di2 = cm
3Solutions
1.Kinematics
Answer: s = 24.11 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Units
v₀ = 50/3.6 = 13.89 m/s
Braking distance
0 = v₀² − 2·a·s → s = v₀²/(2a) = 13.89²/(2·4) = 24.11 m
Answer
s = 24.11 m
2.Kinematics
Answer: hmax = 48.05 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Rise above the roof
0 = v₀² − 2·g·Δh → Δh = 16²/(2·9.81) = 13.05 m
Height above the ground
hmax = 35 + 13.05 = 48.05 m
Answer
hmax = 48.05 m
3.Newton’s laws
Answer: a = 3.355 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 28·cos 70° = 9.577 m/s
vy = v0·sin θ = 28·sin 70° = 26.31 m/s
Highest point
At the top the vertical velocity is zero: vy² = 2gH.
H = vy²/(2g) = 26.31²/(2·9.81) = 35.28 m
Answer
H = 35.28 m
6.Projectile motion
Answer: x = 22.41 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 12·cos 55° = 6.883 m/s
vy = v0·sin θ = 12·sin 55° = 9.83 m/s
Time in the air
Solve y(t) = h + vy·t − ½gt² = 0 for the positive root.
0 = 20 + 9.83·t − 4.905·t²
t = (vy + √(vy² + 2gh))/g = (9.83 + √(96.63 + 392.4))/9.81 = 3.256 s
Horizontal distance
x = vx·t = 6.883·3.256 = 22.41 m
Answer
x = 22.41 m
7.Work & energy
Answer: Wf = 5.07 J
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Friction force
N = mg·cos θ = 4.905·0.9397 = 4.609 N
F = μN = 0.1·4.609 = 0.4609 N
Work against friction
Wf = F·d = 0.4609·11 = 5.07 J
Answer
Wf = 5.07 J
8.Work & energy
Answer: N = 58.86 N
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d). On a circular path the net force towards the centre must equal mv²/r.
Speed at the top
v² = 2g(h − 2R) = 2·9.81·(4 − 2) = 39.24 m²/s²
Forces at the top
m·g = 2·9.81 = 19.62 N
N = mv²/R − mg = 2·39.24/1 − 19.62 = 58.86 N
Answer
N = 58.86 N
The cart just makes it round when h = 2.5R; then N = 0 at the top.
9.Momentum & collisions
Answer: v′1 = 0.7143 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Elastic collision with a target at rest
Solving momentum and energy conservation together gives these two results.
v′1 = (2 − 1.5)/(2 + 1.5)·5 = 0.7143 m/s
v′2 = 2·2/(2 + 1.5)·5 = 5.714 m/s
Answer
v′1 = 0.7143 m/s
10.Momentum & collisions
Answer: v1 = 31.18 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 2.5 + 1.5/2 = 3.25 m
A = H·b = 1.5·1.5 = 2.25 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·3.25·2.25 = 71.74 kN
Answer
F = 71.74 kN
12.Hydrostatic force
Answer: ycp = 5.067 m
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 4 + 2/2 = 5 m
A = H·b = 2·2 = 4 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·5·4 = 196.2 kN
Centre of pressure
Pressure grows with depth, so the resultant acts below the centroid.
Ic = b·H³/12 = 2·2³/12 = 1.333 m⁴
ycp = yc + Ic/(yc·A) = 5 + 1.333/(5·4) = 5.067 m
Answer
ycp = 5.067 m
13.Continuity & Bernoulli
Answer: p1 = 302.8 kPa
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Combined gas law: for a fixed amount of ideal gas, P1V1/T1 = P2V2/T2.
Absolute temperatures
T1 = 288.1 K, T2 = 503.1 K
Combined gas law
V2 = V1·(P1/P2)·(T2/T1) = 20·(400/700)·(503.1/288.1) = 19.96 L
Answer
V2 = 19.96 L
17.Heat engines & refrigerators
Answer: TL = 20 °C
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperature of the source
TH = 450 + 273.15 = 723.1 K
Reversible heat ratio
TL = TH·QL/QH = 723.1·1054/2600 = 293.2 K = 20 °C
Answer
TL = 20 °C
18.Heat engines & refrigerators
Answer: Ẇ = 1.122 kW
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 21 + 273.15 = 294.1 K
TL = 10 + 273.15 = 283.1 K
Carnot and actual COP
COPmax = 294.1/(294.1 − 283.1) = 26.74
COP = 0.35·26.74 = 9.359
Power input
Ẇ = Q̇H/COP = 10.5/9.359 = 1.122 kW
Answer
Ẇ = 1.122 kW
19.Waves, sound & optics
Answer: hi = 15 cm
Geometric optics: at a boundary, n₁·sin θ₁ = n₂·sin θ₂ (Snell's law), with angles measured from the normal and n = c/v. Going into a slower medium the ray bends towards the normal. From a denser medium (n₁ > n₂) beyond the critical angle θc = arcsin(n₂/n₁) all light is reflected: total internal reflection. Thin lenses and spherical mirrors obey 1/f = 1/do + 1/di with the magnification m = −di/do. Sign convention: f > 0 for a converging lens and a concave mirror (f = R/2), f < 0 for a diverging lens and a convex mirror; di > 0 for a real image, di < 0 for a virtual one, and m < 0 for an inverted image.
Thin-lens equation
1/di = 1/f − 1/do = 1/15 − 1/10
di = −30 cm
Magnification and height
m = −(−30)/10 = 3
hi = 3·5 = 15 cm
Answer
hi = 15 cm
20.Waves, sound & optics
Answer: di2 = 6.346 cm
Geometric optics: at a boundary, n₁·sin θ₁ = n₂·sin θ₂ (Snell's law), with angles measured from the normal and n = c/v. Going into a slower medium the ray bends towards the normal. From a denser medium (n₁ > n₂) beyond the critical angle θc = arcsin(n₂/n₁) all light is reflected: total internal reflection. Thin lenses and spherical mirrors obey 1/f = 1/do + 1/di with the magnification m = −di/do. Sign convention: f > 0 for a converging lens and a concave mirror (f = R/2), f < 0 for a diverging lens and a convex mirror; di > 0 for a real image, di < 0 for a virtual one, and m < 0 for an inverted image.