Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A car driving at 80 km/h brakes with a constant deceleration of 4.5 m/s² until it stops. Find the braking distance s.
v₀ = 80 km/ha = −4.5 m/s²v = 0
s = m
2.KinematicsHard
A ball is thrown straight up at 15 m/s from the edge of a roof 35 m above the ground. Ignore air resistance and use g = 9.81 m/s². Find the greatest height hmax above the ground.
v₀ = 15 m/sh₀ = 35 mg = 9.81 m/s²
hmax = m
3.Newton’s lawsMedium
A 5 kg block slides down a slope at 40° to the horizontal. The coefficient of kinetic friction is 0.1. Use g = 9.81 m/s². Find the acceleration a of the block along the slope.
m = 5 kgθ = 40°μ = 0.1g = 9.81 m/s²
a = m/s²
4.Newton’s lawsHard
Two blocks on a level floor are joined by a light horizontal string. A horizontal force of 100 N pulls the front 3 kg block; the 9 kg block is towed behind. The coefficient of kinetic friction is 0.15 for both blocks. Use g = 9.81 m/s². Find the tension T in the connecting string.
m1 = 9 kgm2 = 3 kgF = 100 Nμ = 0.15g = 9.81 m/s²
T = N
5.Projectile motionMedium
A ball is launched at 25° above horizontal from level ground. Ignore air resistance. Find the horizontal distance x travelled before the ball hits the ground.
v0 = 40 m/sθ = 25°g = 9.81 m/s²
x = m
6.Projectile motionHard
A ball is launched at 20° above horizontal from the top of a 50 m cliff. Ignore air resistance. Find the time of flight t until the ball hits the ground.
v0 = 30 m/sθ = 20°h = 50 mg = 9.81 m/s²
t = s
7.Work & energyMedium
A 1 kg ball hangs on a light string of length 1.5 m. It is pulled aside until the string makes 45° with the vertical and released from rest. Find the tension T in the string when the ball passes the lowest point.
m = 1 kgL = 1.5 mθ = 45°g = 9.81 m/s²
T = N
8.Work & energyHard
A 10 kg block rests on a rough horizontal table (μ = 0.25). A light string runs from it over a smooth pulley at the edge of the table to a hanging 3 kg block. The system is released from rest. Find the speed v of the blocks after the hanging block has dropped 2 m.
m1 = 10 kgm2 = 3 kgμ = 0.25d = 2 mg = 9.81 m/s²
v = m/s
9.Momentum & collisionsMedium
A 12 g bullet is fired horizontally into a 1.5 kg wooden block hanging on light strings, and stays inside it. The block swings up until it is 21 cm higher than at the start. Use g = 9.81 m/s². Find the speed v of the bullet before impact.
m = 12 gM = 1.5 kgh = 21 cmg = 9.81 m/s²
v = m/s
10.Momentum & collisionsHard
A 0.1 kg ball hits a wall at 15 m/s and bounces straight back at 14 m/s. The contact lasts 5 ms. Find the average force Favg of the wall on the ball.
m = 0.1 kgvin = 15 m/svout = 14 m/sΔt = 5 ms
Favg = N
11.Hydrostatic forceMedium
A vertical rectangular gate 2 m wide sits in the wall of a tank of water, with its top edge 2 m below the surface. Find the resultant hydrostatic force F on the gate.
A vertical rectangular gate 3 m wide sits in the wall of a tank of water, with its top edge 1.5 m below the surface. Find the resultant hydrostatic force F on the gate.
A pitot-static tube in a wind tunnel reads a difference of 1250 Pa between the stagnation pressure and the static pressure. The air density is 1.2 kg/m³. Find the air speed v.
p0 − p = 1250 Paρ = 1.2 kg/m³
v = m/s
14.Continuity & BernoulliHard
Water flows up through a pipe that narrows from 75 mm to 40 mm while rising 9 m. At section 1 the pressure is 150 kPa and the velocity is 2.25 m/s. Ignoring losses, find the pressure p2 at section 2.
A heat engine receives heat from a source at 300 °C and rejects heat to the surroundings at 15 °C. Its actual thermal efficiency is 37%. Find its second-law efficiency ηII, the ratio of the actual efficiency to the Carnot efficiency.
TH = 300 °CTL = 15 °Cη = 37%
ηII = %
18.Heat engines & refrigeratorsHard
A heat pump keeps a house at 20 °C while it is -5 °C outside, delivering 10 kW of heat to the house. Find the minimum power input Ẇmin.
TH = 20 °CTL = -5 °CQ̇H = 10 kW
Ẇmin = kW
19.Waves, sound & opticsMedium
Light travels in ethanol (n = 1.36) towards a flat boundary with water (n = 1.33). Find the critical angle θc beyond which it is totally reflected.
n1 = 1.36n2 = 1.33
θc = °
20.Waves, sound & opticsHard
Light of wavelength 550 nm passes through a single slit 0.1 mm wide. Find the angle θ2 of dark fringe number 2 from the straight-through direction.
λ = 550 nma = 0.1 mmm = 2
θ2 = °
3Solutions
1.Kinematics
Answer: s = 54.87 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Units
v₀ = 80/3.6 = 22.22 m/s
Braking distance
0 = v₀² − 2·a·s → s = v₀²/(2a) = 22.22²/(2·4.5) = 54.87 m
Answer
s = 54.87 m
2.Kinematics
Answer: hmax = 46.47 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Rise above the roof
0 = v₀² − 2·g·Δh → Δh = 15²/(2·9.81) = 11.47 m
Height above the ground
hmax = 35 + 11.47 = 46.47 m
Answer
hmax = 46.47 m
3.Newton’s laws
Answer: a = 5.554 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
With the same μ on both blocks, friction drops out: T = F·m₁/(m₁ + m₂).
5.Projectile motion
Answer: x = 124.9 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 40·cos 25° = 36.25 m/s
vy = v0·sin θ = 40·sin 25° = 16.9 m/s
Time in the air
Starting and landing at the same height: t = 2vy/g.
t = 2·16.9/9.81 = 3.446 s
Horizontal distance
x = vx·t = 36.25·3.446 = 124.9 m
Answer
x = 124.9 m
6.Projectile motion
Answer: t = 4.406 s
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 30·cos 20° = 28.19 m/s
vy = v0·sin θ = 30·sin 20° = 10.26 m/s
Time in the air
Solve y(t) = h + vy·t − ½gt² = 0 for the positive root.
0 = 50 + 10.26·t − 4.905·t²
t = (vy + √(vy² + 2gh))/g = (10.26 + √(105.3 + 981))/9.81 = 4.406 s
Answer
t = 4.406 s
7.Work & energy
Answer: T = 15.56 N
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d). On a circular path the net force towards the centre must equal mv²/r.
Speed at the bottom
v² = 2gL(1 − cos θ) = 2·9.81·1.5·(1 − cos 45°) = 8.62 m²/s²
Forces at the bottom
m·g = 1·9.81 = 9.81 N
T = mg + mv²/L = 9.81 + 1·8.62/1.5 = 15.56 N
Answer
T = 15.56 N
Check: T = mg(3 − 2cos θ) = 15.56 N.
8.Work & energy
Answer: v = 1.229 m/s
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy released and lost
m₂g·d = 29.43·2 = 58.86 J
μ·m₁g·d = 0.25·98.1·2 = 49.05 J
Kinetic energy of both blocks
½(m₁ + m₂)v² = 9.81 → v = √(2·9.81/13) = 1.229 m/s
Answer
v = 1.229 m/s
9.Momentum & collisions
Answer: v = 255.8 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Swing after impact
V = √(2·g·h) = √(2·9.81·0.21) = 2.03 m/s
Collision
m·v = (m + M)·V → v = (0.012 + 1.5)·2.03/0.012 = 255.8 m/s
Answer
v = 255.8 m/s
10.Momentum & collisions
Answer: Favg = 580 N
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Change in momentum
J = m·Δv = 0.1·(14 + 15) = 2.9 N·s
Average force
Favg = J/Δt = 2.9/0.005 = 580 N
Answer
Favg = 580 N
11.Hydrostatic force
Answer: F = 80.93 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 2 + 1.5/2 = 2.75 m
A = H·b = 1.5·2 = 3 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·2.75·3 = 80.93 kN
Answer
F = 80.93 kN
12.Hydrostatic force
Answer: F = 264.9 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 1.5 + 3/2 = 3 m
A = H·b = 3·3 = 9 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·3·9 = 264.9 kN
Answer
F = 264.9 kN
13.Continuity & Bernoulli
Answer: v = 45.64 m/s
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Bernoulli to the stagnation point
The flow comes to rest at the tip, so its kinetic energy shows up as extra pressure.
p0 − p = ½ρv²
v = √(2·1250/1.2) = 45.64 m/s
Answer
v = 45.64 m/s
14.Continuity & Bernoulli
Answer: p2 = 32.96 kPa
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Combined gas law: for a fixed amount of ideal gas, P1V1/T1 = P2V2/T2.
Absolute temperatures
T1 = 313.1 K, T2 = 383.1 K
Combined gas law
V2 = V1·(P1/P2)·(T2/T1) = 2·(400/100)·(383.1/313.1) = 9.788 L
Answer
V2 = 9.788 L
17.Heat engines & refrigerators
Answer: ηII = 74.41 %
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 300 + 273.15 = 573.1 K
TL = 15 + 273.15 = 288.1 K
Carnot efficiency
ηCarnot = 1 − 288.1/573.1 = 49.73 %
Second-law efficiency
ηII = η/ηCarnot = 37/49.73 = 74.41 %
Answer
ηII = 74.41 %
18.Heat engines & refrigerators
Answer: Ẇmin = 0.8528 kW
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
The least work is needed by a reversible machine, which has the highest COP.
Ẇmin = Q̇H/COP = 10/11.73 = 0.8528 kW
Answer
Ẇmin = 0.8528 kW
19.Waves, sound & optics
Answer: θc = 77.94 °
Geometric optics: at a boundary, n₁·sin θ₁ = n₂·sin θ₂ (Snell's law), with angles measured from the normal and n = c/v. Going into a slower medium the ray bends towards the normal. From a denser medium (n₁ > n₂) beyond the critical angle θc = arcsin(n₂/n₁) all light is reflected: total internal reflection. Thin lenses and spherical mirrors obey 1/f = 1/do + 1/di with the magnification m = −di/do. Sign convention: f > 0 for a converging lens and a concave mirror (f = R/2), f < 0 for a diverging lens and a convex mirror; di > 0 for a real image, di < 0 for a virtual one, and m < 0 for an inverted image.
Refraction at 90°
sin θc = n₂/n₁ = 1.33/1.36 = 0.9779
Critical angle
θc = arcsin(0.9779) = 77.94°
Answer
θc = 77.94°
20.Waves, sound & optics
Answer: θ2 = 0.6303 °
Interference and diffraction: light from two slits a distance d apart reaches a point on the screen with a path difference d·sin θ. Bright fringes appear where d·sin θ = mλ (m = 0, ±1, ±2, …). For a screen at distance L ≫ d, the m-th bright fringe is at y = mλL/d and the fringe spacing is Δy = λL/d. A grating with N lines per millimetre has d = 1/N and sharp maxima at d·sin θ = mλ; since sin θ ≤ 1, the highest order is the largest whole number m ≤ d/λ. A single slit of width a has dark fringes at a·sin θ = mλ, m = ±1, ±2, …