Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A plane starts from rest and accelerates uniformly at 1.5 m/s² along a runway. Find its speed v after 2000 m.
v₀ = 0a = 1.5 m/s²s = 2000 m
v = m/s
2.KinematicsHard
A stone is dropped from rest into a well. The splash is heard 4.8 s after the stone is released. The speed of sound is 343 m/s; ignore air resistance and use g = 9.81 m/s². Find the depth d of the well.
ttotal = 4.8 svsound = 343 m/sg = 9.81 m/s²
d = m
3.Newton’s lawsMedium
A 17 kg block slides down a slope at 30° to the horizontal. The coefficient of kinetic friction is 0.25. Use g = 9.81 m/s². Find the acceleration a of the block along the slope.
m = 17 kgθ = 30°μ = 0.25g = 9.81 m/s²
a = m/s²
4.Newton’s lawsHard
A 3 kg block on a horizontal table is connected by a light string over a frictionless pulley to a hanging 4.5 kg mass. The coefficient of kinetic friction between block and table is 0.25. Use g = 9.81 m/s². Find the tension T in the string.
m1 = 3 kgm2 = 4.5 kgμ = 0.25g = 9.81 m/s²
T = N
5.Projectile motionMedium
A ball is launched from level ground at 40 m/s and must land 50 m away. Ignore air resistance and use g = 9.81 m/s². Find the smaller of the two possible launch angles θ.
v₀ = 40 m/sR = 50 mg = 9.81 m/s²
θ = °
6.Projectile motionHard
A ball is thrown from ground level at 25 m/s and 40° above the horizontal. It lands on the flat roof of a building 6 m high, on its way down. Ignore air resistance and use g = 9.81 m/s². Find the horizontal distance x from the launch point to where it lands.
v₀ = 25 m/sθ = 40°hroof = 6 mg = 9.81 m/s²
x = m
7.Work & energyMedium
A 2.5 kg block slides 17 m down a slope at 40° to the horizontal, with a coefficient of kinetic friction of 0.2. Find the work Wf done against friction.
m = 2.5 kgθ = 40°μ = 0.2d = 17 mg = 9.81 m/s²
Wf = J
8.Work & energyHard
A 2 kg block rests on a rough horizontal table (μ = 0.1). A light string runs from it over a smooth pulley at the edge of the table to a hanging 6 kg block. The system is released from rest. Find the speed v of the blocks after the hanging block has dropped 0.5 m.
m1 = 2 kgm2 = 6 kgμ = 0.1d = 0.5 mg = 9.81 m/s²
v = m/s
9.Momentum & collisionsMedium
A 5 kg glider moving at 5 m/s makes a perfectly elastic head-on collision with a 1 kg glider at rest on a frictionless track. Find the velocity v′1 of the first glider after the collision (positive in its original direction).
m1 = 5 kgm2 = 1 kgv1 = 5 m/sv2 = 0
v′1 = m/s
10.Momentum & collisionsHard
A 0.4 kg ball hits a wall at 30 m/s and bounces straight back at 4 m/s. The contact lasts 20 ms. Find the average force Favg of the wall on the ball.
m = 0.4 kgvin = 30 m/svout = 4 m/sΔt = 20 ms
Favg = N
11.Hydrostatic forceMedium
A vertical rectangular gate 1.5 m wide sits in the wall of a tank of water, with its top edge 2 m below the surface. Find the resultant hydrostatic force F on the gate.
A vertical rectangular gate 1 m wide sits in the wall of a tank of glycerin, with its top edge 2 m below the surface. Find the depth ycp of the centre of pressure below the surface.
Water flows through a horizontal pipe that narrows from 100 mm to 50 mm. In the wide section the pressure is 120 kPa and the velocity is 1.75 m/s. Ignoring losses, find the pressure p2 in the narrow section.
A horizontal venturi meter (inlet 200 mm, throat 150 mm) carries water. A mercury U-tube manometer connected between the inlet and the throat shows a level difference of 170 mm. The discharge coefficient is 0.95. Find the flow rate Q. Use ρ = 1000 kg/m³ for water, 13 600 kg/m³ for mercury and g = 9.81 m/s².
A reversible (Carnot) heat engine takes in 2800 kJ of heat from a reservoir at 700 °C and rejects 843 kJ per cycle. Find the temperature TL of the cold reservoir in °C.
TH = 700 °CQH = 2800 kJQL = 843 kJ
TL = °C
18.Heat engines & refrigeratorsHard
Two Carnot engines work in series. Engine A receives heat from a reservoir at 650 °C and rejects heat to an intermediate reservoir at temperature Tm. Engine B takes all that heat and rejects heat to a reservoir at 10 °C. Both engines produce the same work. Find Tm in °C.
TH = 650 °CTL = 10 °C
Tm = °C
19.Waves, sound & opticsMedium
An observer moves at 5 m/s away from a stationary source of 1200 Hz. The speed of sound is 343 m/s. Find the frequency f′ that the observer hears.
f = 1200 Hzv = 343 m/svo = 5 m/s
f′ = Hz
20.Waves, sound & opticsHard
Light of wavelength 500 nm falls at right angles on a grating with 400 lines per millimetre. Find the angle θ1 of the order-1 maximum.
N = 400 mm⁻¹λ = 500 nmm = 1
θ1 = °
3Solutions
1.Kinematics
Answer: v = 77.46 m/s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Speed after the distance
v = √(2·a·s) = √(2·1.5·2000) = 77.46 m/s
Answer
v = 77.46 m/s
(278.9 km/h)
2.Kinematics
Answer: d = 99.73 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Two parts of the time
½·9.81·t₁² = 343·(4.8 − t₁)
4.905·t₁² + 343·t₁ − 1646 = 0
Fall time
Only the positive root is physical.
t₁ = (−343 + √(343² + 4·4.905·1646))/(2·4.905) = 4.509 s
Depth
d = ½·9.81·4.509² = 99.73 m
Answer
d = 99.73 m
3.Newton’s laws
Answer: a = 2.781 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Range formula
R = v₀²·sin 2θ/g → sin 2θ = 9.81·50/40² = 0.3066
Angle
2θ = 17.85° → θ = 8.926°
Answer
θ = 8.926°
The other solution is 90° − θ = 81.07°.
6.Projectile motion
Answer: x = 54.51 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
vx = 19.15 m/s, vy = 16.07 m/s
Time to land on the roof
Larger root: the ball is descending.
6 = 16.07·t − 4.905·t²
t = (16.07 + √(16.07² − 2·9.81·6))/9.81 = 2.846 s
Horizontal distance
x = vx·t = 19.15·2.846 = 54.51 m
Answer
x = 54.51 m
7.Work & energy
Answer: Wf = 63.88 J
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Friction force
N = mg·cos θ = 24.53·0.766 = 18.79 N
F = μN = 0.2·18.79 = 3.757 N
Work against friction
Wf = F·d = 3.757·17 = 63.88 J
Answer
Wf = 63.88 J
8.Work & energy
Answer: v = 2.667 m/s
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy released and lost
m₂g·d = 58.86·0.5 = 29.43 J
μ·m₁g·d = 0.1·19.62·0.5 = 0.981 J
Kinetic energy of both blocks
½(m₁ + m₂)v² = 28.45 → v = √(2·28.45/8) = 2.667 m/s
Answer
v = 2.667 m/s
9.Momentum & collisions
Answer: v′1 = 3.333 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Elastic collision with a target at rest
Solving momentum and energy conservation together gives these two results.
v′1 = (5 − 1)/(5 + 1)·5 = 3.333 m/s
v′2 = 2·5/(5 + 1)·5 = 8.333 m/s
Answer
v′1 = 3.333 m/s
10.Momentum & collisions
Answer: Favg = 680 N
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Change in momentum
J = m·Δv = 0.4·(4 + 30) = 13.6 N·s
Average force
Favg = J/Δt = 13.6/0.02 = 680 N
Answer
Favg = 680 N
11.Hydrostatic force
Answer: F = 88.29 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 2 + 2/2 = 3 m
A = H·b = 2·1.5 = 3 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·3·3 = 88.29 kN
Answer
F = 88.29 kN
12.Hydrostatic force
Answer: ycp = 3.41 m
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 2 + 2.5/2 = 3.25 m
A = H·b = 2.5·1 = 2.5 m²
Resultant force
F = ρ·g·yc·A = 1260·9.81·3.25·2.5 = 100.4 kN
Centre of pressure
Pressure grows with depth, so the resultant acts below the centroid.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Pressure difference from the manometer
Δp = (13600 − 1000)·9.81·0.17 = 21013 Pa
Throat velocity
Continuity and Bernoulli together give the ideal throat velocity.
Combined gas law: for a fixed amount of ideal gas, P1V1/T1 = P2V2/T2.
Absolute temperatures
T1 = 298.1 K, T2 = 373.1 K
Combined gas law
V2 = V1·(P1/P2)·(T2/T1) = 10·(250/750)·(373.1/298.1) = 4.172 L
Answer
V2 = 4.172 L
17.Heat engines & refrigerators
Answer: TL = 19.84 °C
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperature of the source
TH = 700 + 273.15 = 973.1 K
Reversible heat ratio
TL = TH·QL/QH = 973.1·843/2800 = 293 K = 19.84 °C
Answer
TL = 19.84 °C
18.Heat engines & refrigerators
Answer: Tm = 330 °C
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 650 + 273.15 = 923.1 K
TL = 10 + 273.15 = 283.1 K
Equal work
W = Q·(1 − Tlow/Thigh) and Q/T is the same at every reservoir, so W is proportional to the temperature drop.
Tm = (923.1 + 283.1)/2 = 603.1 K = 330 °C
Answer
Tm = 330 °C
19.Waves, sound & optics
Answer: f′ = 1183 Hz
Standing waves and the Doppler effect: a string fixed at both ends, or a pipe open at both ends, fits whole half-wavelengths: L = nλ/2, fn = n·v/(2L), n = 1, 2, 3, … A pipe closed at one end has a node at the closed end and an antinode at the open end: L = nλ/4 with odd n only, fn = n·v/(4L). When source or observer move along the line between them, f′ = f·(v ± vo)/(v ∓ vs): use the upper signs for motion towards each other. Two waves of nearly equal frequency beat at |f₁ − f₂|.
Interference and diffraction: light from two slits a distance d apart reaches a point on the screen with a path difference d·sin θ. Bright fringes appear where d·sin θ = mλ (m = 0, ±1, ±2, …). For a screen at distance L ≫ d, the m-th bright fringe is at y = mλL/d and the fringe spacing is Δy = λL/d. A grating with N lines per millimetre has d = 1/N and sharp maxima at d·sin θ = mλ; since sin θ ≤ 1, the highest order is the largest whole number m ≤ d/λ. A single slit of width a has dark fringes at a·sin θ = mλ, m = ±1, ±2, …