Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A car driving at 72 km/h brakes with a constant deceleration of 7.5 m/s² until it stops. How long does braking take? Find t.
v₀ = 72 km/ha = −7.5 m/s²v = 0
t = s
2.KinematicsHard
A ball is thrown straight up at 5 m/s from the edge of a roof 15 m above the ground. Ignore air resistance and use g = 9.81 m/s². How long after the throw does it hit the ground? Find t.
v₀ = 5 m/sh₀ = 15 mg = 9.81 m/s²
t = s
3.Newton’s lawsMedium
An 18 kg block slides down a slope at 35° to the horizontal. The coefficient of kinetic friction is 0.3. Use g = 9.81 m/s². Find the acceleration a of the block along the slope.
m = 18 kgθ = 35°μ = 0.3g = 9.81 m/s²
a = m/s²
4.Newton’s lawsHard
A 7 kg block on a ramp at 25° is connected by a light string over a frictionless pulley at the top of the ramp to a hanging 7.5 kg mass. The hanging mass moves down. The coefficient of kinetic friction between block and ramp is 0.1. Use g = 9.81 m/s². Find the tension T in the string.
m1 = 7 kgm2 = 7.5 kgθ = 25°μ = 0.1g = 9.81 m/s²
T = N
5.Projectile motionMedium
A ball is launched at 55° above horizontal from level ground. Ignore air resistance. Find the time of flight t until the ball hits the ground.
v0 = 30 m/sθ = 55°g = 9.81 m/s²
t = s
6.Projectile motionHard
A ball is launched at 26 m/s and 25° above the horizontal from the top of a 40 m cliff. Ignore air resistance and use g = 9.81 m/s². Find the greatest height H above the ground at the foot of the cliff.
v₀ = 26 m/sθ = 25°h = 40 mg = 9.81 m/s²
H = m
7.Work & energyMedium
A block slides from rest down a slope at 40° to the horizontal. The coefficient of kinetic friction is 0.35. Find its speed v after it has slid 16 m along the slope.
θ = 40°μ = 0.35d = 16 mg = 9.81 m/s²
v = m/s
8.Work & energyHard
A 5 kg block is released from rest at height 2.5 m on a smooth ramp. At the bottom it crosses a rough horizontal strip 1.5 m long (μ = 0.15) and then runs onto a spring (k = 2500 N/m) on a smooth surface. Find the maximum compression x of the spring.
m = 5 kgh = 2.5 mL = 1.5 mμ = 0.15k = 2500 N/mg = 9.81 m/s²
x = cm
9.Momentum & collisionsMedium
A 3 kg glider moving at 2 m/s makes a perfectly elastic head-on collision with a 3.5 kg glider at rest on a frictionless track. Find the velocity v′2 of the second glider after the collision.
m1 = 3 kgm2 = 3.5 kgv1 = 2 m/sv2 = 0
v′2 = m/s
10.Momentum & collisionsHard
A 0.4 kg ball hits a wall at 29 m/s and bounces straight back at 6 m/s. The contact lasts 25 ms. Find the average force Favg of the wall on the ball.
m = 0.4 kgvin = 29 m/svout = 6 m/sΔt = 25 ms
Favg = N
11.Hydrostatic forceMedium
A vertical rectangular gate 1.5 m wide sits in the wall of a tank of water, with its top edge 2.5 m below the surface. Find the resultant hydrostatic force F on the gate.
A vertical rectangular gate 3 m wide sits in the wall of a tank of seawater, with its top edge 4 m below the surface. Find the depth ycp of the centre of pressure below the surface.
d = 4 mH = 1 mb = 3 mρ = 1025 kg/m³g = 9.81 m/s²
ycp = m
13.Continuity & BernoulliMedium
Water flows through a horizontal pipe that narrows from 75 mm to 40 mm. In the wide section the pressure is 250 kPa and the velocity is 2.75 m/s. Ignoring losses, find the pressure p2 in the narrow section.
Water flows up through a pipe that narrows from 100 mm to 75 mm while rising 4 m. At section 1 the pressure is 310 kPa and the velocity is 3 m/s. Ignoring losses, find the pressure p2 at section 2.
A reversible (Carnot) heat engine takes in 3000 kJ of heat from a reservoir at 350 °C and rejects 1315 kJ per cycle. Find the temperature TL of the cold reservoir in °C.
TH = 350 °CQH = 3000 kJQL = 1315 kJ
TL = °C
18.Heat engines & refrigeratorsHard
Two Carnot engines work in series. Engine A receives heat from a reservoir at 1150 °C and rejects heat to an intermediate reservoir at temperature Tm. Engine B takes all that heat and rejects heat to a reservoir at 35 °C. Both engines have the same thermal efficiency. Find Tm in °C.
TH = 1150 °CTL = 35 °C
Tm = °C
19.Waves, sound & opticsMedium
Light travels in glycerol (n = 1.47) towards a flat boundary with ethanol (n = 1.36). Find the critical angle θc beyond which it is totally reflected.
n1 = 1.47n2 = 1.36
θc = °
20.Waves, sound & opticsHard
Light of wavelength 450 nm passes through a single slit 0.08 mm wide. Find the width w of the central bright maximum on a screen 1 m away (between the first dark fringes on either side).
λ = 450 nma = 0.08 mmL = 1 m
w = mm
3Solutions
1.Kinematics
Answer: t = 2.667 s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Units
v₀ = 72/3.6 = 20 m/s
Braking time
0 = v₀ − a·t → t = v₀/a = 20/7.5 = 2.667 s
Answer
t = 2.667 s
2.Kinematics
Answer: t = 2.331 s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Equation of motion
Up is positive and the ground is h₀ below the starting point.
−15 = 5·t − ½·9.81·t²
4.905·t² − 5·t − 15 = 0
Solve the quadratic
Only the positive root is physical.
t = (5 + √(5² + 2·9.81·15))/9.81 = 2.331 s
Answer
t = 2.331 s
3.Newton’s laws
Answer: a = 3.216 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Forces along the string
m₂·g = 73.58 N
m₁·g·sin θ = 29.02 N
μ·m₁·g·cos θ = 6.224 N
Acceleration of the system
a = (73.58 − 29.02 − 6.224)/14.5 = 2.643 m/s²
Tension from the hanging mass
m2·g − T = m2·a → T = 7.5·(9.81 − 2.643) = 53.75 N
Answer
T = 53.75 N
5.Projectile motion
Answer: t = 5.01 s
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 30·cos 55° = 17.21 m/s
vy = v0·sin θ = 30·sin 55° = 24.57 m/s
Time in the air
Starting and landing at the same height: t = 2vy/g.
t = 2·24.57/9.81 = 5.01 s
Answer
t = 5.01 s
6.Projectile motion
Answer: H = 46.15 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Vertical launch speed
vy = 26·sin 25° = 10.99 m/s
Rise above the cliff
Δh = vy²/(2g) = 10.99²/(2·9.81) = 6.154 m
Height above the ground
H = 40 + 6.154 = 46.15 m
Answer
H = 46.15 m
7.Work & energy
Answer: v = 10.85 m/s
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy balance along the slope
The block drops a height d·sin θ while friction removes μmg·cos θ·d. The mass cancels.
½v² = g·d·(sin θ − μ·cos θ)
v = √(2·9.81·16·(0.6428 − 0.35·0.766)) = 10.85 m/s
Answer
v = 10.85 m/s
8.Work & energy
Answer: x = 29.88 cm
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy left after the rough strip
The ramp is smooth, so only the strip removes energy.
mgh − μmgL = 49.05·(2.5 − 0.15·1.5) = 111.6 J
Maximum compression
½kx² = 111.6 → x = √(2·111.6/2500) = 0.2988 m = 29.88 cm
Answer
x = 29.88 cm
9.Momentum & collisions
Answer: v′2 = 1.846 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Elastic collision with a target at rest
Solving momentum and energy conservation together gives these two results.
v′1 = (3 − 3.5)/(3 + 3.5)·2 = −0.1538 m/s
v′2 = 2·3/(3 + 3.5)·2 = 1.846 m/s
Answer
v′2 = 1.846 m/s
10.Momentum & collisions
Answer: Favg = 560 N
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Change in momentum
J = m·Δv = 0.4·(6 + 29) = 14 N·s
Average force
Favg = J/Δt = 14/0.025 = 560 N
Answer
Favg = 560 N
11.Hydrostatic force
Answer: F = 44.15 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 2.5 + 1/2 = 3 m
A = H·b = 1·1.5 = 1.5 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·3·1.5 = 44.15 kN
Answer
F = 44.15 kN
12.Hydrostatic force
Answer: ycp = 4.519 m
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 4 + 1/2 = 4.5 m
A = H·b = 1·3 = 3 m²
Resultant force
F = ρ·g·yc·A = 1025·9.81·4.5·3 = 135.7 kN
Centre of pressure
Pressure grows with depth, so the resultant acts below the centroid.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Combined gas law: for a fixed amount of ideal gas, P1V1/T1 = P2V2/T2.
Absolute temperatures
T1 = 283.1 K, T2 = 453.1 K
Combined gas law
V2 = V1·(P1/P2)·(T2/T1) = 2·(300/100)·(453.1/283.1) = 9.602 L
Answer
V2 = 9.602 L
17.Heat engines & refrigerators
Answer: TL = −0.002583 °C
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperature of the source
TH = 350 + 273.15 = 623.1 K
Reversible heat ratio
TL = TH·QL/QH = 623.1·1315/3000 = 273.1 K = −0.002583 °C
Answer
TL = −0.002583 °C
18.Heat engines & refrigerators
Answer: Tm = 389.1 °C
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 1150 + 273.15 = 1423 K
TL = 35 + 273.15 = 308.1 K
Equal efficiencies
1 − Tm/TH = 1 − TL/Tm gives Tm² = TH·TL.
Tm = √(1423·308.1) = 662.2 K = 389.1 °C
Answer
Tm = 389.1 °C
19.Waves, sound & optics
Answer: θc = 67.69 °
Geometric optics: at a boundary, n₁·sin θ₁ = n₂·sin θ₂ (Snell's law), with angles measured from the normal and n = c/v. Going into a slower medium the ray bends towards the normal. From a denser medium (n₁ > n₂) beyond the critical angle θc = arcsin(n₂/n₁) all light is reflected: total internal reflection. Thin lenses and spherical mirrors obey 1/f = 1/do + 1/di with the magnification m = −di/do. Sign convention: f > 0 for a converging lens and a concave mirror (f = R/2), f < 0 for a diverging lens and a convex mirror; di > 0 for a real image, di < 0 for a virtual one, and m < 0 for an inverted image.
Refraction at 90°
sin θc = n₂/n₁ = 1.36/1.47 = 0.9252
Critical angle
θc = arcsin(0.9252) = 67.69°
Answer
θc = 67.69°
20.Waves, sound & optics
Answer: w = 11.25 mm
Interference and diffraction: light from two slits a distance d apart reaches a point on the screen with a path difference d·sin θ. Bright fringes appear where d·sin θ = mλ (m = 0, ±1, ±2, …). For a screen at distance L ≫ d, the m-th bright fringe is at y = mλL/d and the fringe spacing is Δy = λL/d. A grating with N lines per millimetre has d = 1/N and sharp maxima at d·sin θ = mλ; since sin θ ≤ 1, the highest order is the largest whole number m ≤ d/λ. A single slit of width a has dark fringes at a·sin θ = mλ, m = ±1, ±2, …