Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A car driving at 36 km/h brakes with a constant deceleration of 6 m/s² until it stops. Find the braking distance s.
v₀ = 36 km/ha = −6 m/s²v = 0
s = m
2.KinematicsHard
A ball is thrown straight up at 18 m/s from the edge of a roof 35 m above the ground. Ignore air resistance and use g = 9.81 m/s². How long after the throw does it hit the ground? Find t.
v₀ = 18 m/sh₀ = 35 mg = 9.81 m/s²
t = s
3.Newton’s lawsMedium
A 7 kg block slides down a slope at 30° to the horizontal. The coefficient of kinetic friction is 0.15. Use g = 9.81 m/s². Find the acceleration a of the block along the slope.
m = 7 kgθ = 30°μ = 0.15g = 9.81 m/s²
a = m/s²
4.Newton’s lawsHard
A 10 kg block on a horizontal table is connected by a light string over a frictionless pulley to a hanging 4 kg mass. The coefficient of kinetic friction between block and table is 0.3. Use g = 9.81 m/s². Find the tension T in the string.
m1 = 10 kgm2 = 4 kgμ = 0.3g = 9.81 m/s²
T = N
5.Projectile motionMedium
A ball is kicked from level ground at 38 m/s and 40° above the horizontal towards a wall 43 m away. Ignore air resistance and use g = 9.81 m/s². At what height y does the ball pass the wall?
v₀ = 38 m/sθ = 40°x = 43 mg = 9.81 m/s²
y = m
6.Projectile motionHard
A ball is launched at 22 m/s and 55° above the horizontal from the top of a 45 m cliff. Ignore air resistance and use g = 9.81 m/s². Find the greatest height H above the ground at the foot of the cliff.
v₀ = 22 m/sθ = 55°h = 45 mg = 9.81 m/s²
H = m
7.Work & energyMedium
A 2 kg block slides 8 m down a slope at 20° to the horizontal, with a coefficient of kinetic friction of 0.2. Find the work Wf done against friction.
m = 2 kgθ = 20°μ = 0.2d = 8 mg = 9.81 m/s²
Wf = J
8.Work & energyHard
A 0.5 kg block is released from rest at height 3 m on a smooth ramp. At the bottom it crosses a rough horizontal strip 1 m long (μ = 0.2) and then runs onto a spring (k = 800 N/m) on a smooth surface. Find the speed v of the block when it reaches the spring.
m = 0.5 kgh = 3 mL = 1 mμ = 0.2k = 800 N/mg = 9.81 m/s²
v = m/s
9.Momentum & collisionsMedium
An 800 kg car moving at 22 m/s runs into a stationary 1600 kg car and the two lock together. How much kinetic energy ΔK is lost in the collision?
m1 = 800 kgv1 = 22 m/sm2 = 1600 kgv2 = 0
ΔK = J
10.Momentum & collisionsHard
At a crossing a 1500 kg car travelling east at 11 m/s collides with a 1300 kg car travelling north at 8 m/s. The cars lock together. Find the direction θ of the wreck just after the collision, measured north of east.
m1 = 1500 kgv1 = 11 m/s (E)m2 = 1300 kgv2 = 8 m/s (N)
θ = °
11.Hydrostatic forceMedium
A vertical rectangular gate 1.5 m wide sits in the wall of a tank of water, with its top edge 2 m below the surface. Find the resultant hydrostatic force F on the gate.
A vertical rectangular gate 1 m wide sits in the wall of a tank of oil, with its top edge 2.5 m below the surface. Find the depth ycp of the centre of pressure below the surface.
Water flows through a horizontal venturi meter with an inlet diameter of 200 mm and a throat diameter of 150 mm. The pressure at the inlet is 18 kPa higher than at the throat. Ignoring losses, find the flow rate Q.
A horizontal venturi meter (inlet 200 mm, throat 100 mm) carries water. A mercury U-tube manometer connected between the inlet and the throat shows a level difference of 360 mm. The discharge coefficient is 0.96. Find the flow rate Q. Use ρ = 1000 kg/m³ for water, 13 600 kg/m³ for mercury and g = 9.81 m/s².
A heat engine works between a hot reservoir at 750 °C and a cold reservoir at 20 °C. It takes in 1700 kJ of heat. Find the most work Wmax it could possibly produce.
TH = 750 °CTL = 20 °CQH = 1700 kJ
Wmax = kJ
18.Heat engines & refrigeratorsHard
Two Carnot engines work in series. Engine A receives heat from a reservoir at 1050 °C and rejects heat to an intermediate reservoir at temperature Tm. Engine B takes all that heat and rejects heat to a reservoir at 40 °C. Both engines have the same thermal efficiency. Find Tm in °C.
TH = 1050 °CTL = 40 °C
Tm = °C
19.Waves, sound & opticsMedium
A source of 600 Hz moves at 25 m/s away from a stationary observer. The speed of sound is 343 m/s. Find the frequency f′ that the observer hears.
f = 600 Hzv = 343 m/svs = 25 m/s
f′ = Hz
20.Waves, sound & opticsHard
Two slits 0.25 mm apart are lit with monochromatic light. On a screen 3 m away, bright fringe number 5 lies 39 mm from the central fringe. Find the wavelength λ.
d = 0.25 mmL = 3 my5 = 39 mmm = 5
λ = nm
3Solutions
1.Kinematics
Answer: s = 8.333 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Units
v₀ = 36/3.6 = 10 m/s
Braking distance
0 = v₀² − 2·a·s → s = v₀²/(2a) = 10²/(2·6) = 8.333 m
Answer
s = 8.333 m
2.Kinematics
Answer: t = 5.076 s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Equation of motion
Up is positive and the ground is h₀ below the starting point.
−35 = 18·t − ½·9.81·t²
4.905·t² − 18·t − 35 = 0
Solve the quadratic
Only the positive root is physical.
t = (18 + √(18² + 2·9.81·35))/9.81 = 5.076 s
Answer
t = 5.076 s
3.Newton’s laws
Answer: a = 3.631 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Time to the wall
vx = 38·cos 40° = 29.11 m/s
t = x/vx = 43/29.11 = 1.477 s
Height at that time
y = 24.43·1.477 − ½·9.81·1.477² = 25.38 m
Answer
y = 25.38 m
The ball is still rising at the wall.
6.Projectile motion
Answer: H = 61.55 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Vertical launch speed
vy = 22·sin 55° = 18.02 m/s
Rise above the cliff
Δh = vy²/(2g) = 18.02²/(2·9.81) = 16.55 m
Height above the ground
H = 45 + 16.55 = 61.55 m
Answer
H = 61.55 m
7.Work & energy
Answer: Wf = 29.5 J
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Friction force
N = mg·cos θ = 19.62·0.9397 = 18.44 N
F = μN = 0.2·18.44 = 3.687 N
Work against friction
Wf = F·d = 3.687·8 = 29.5 J
Answer
Wf = 29.5 J
8.Work & energy
Answer: v = 7.412 m/s
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy left after the rough strip
The ramp is smooth, so only the strip removes energy.
mgh − μmgL = 4.905·(3 − 0.2·1) = 13.73 J
Speed at the spring
½mv² = mg(h − μL) → v = √(2g(h − μL)) = √(2·9.81·2.8) = 7.412 m/s
Answer
v = 7.412 m/s
9.Momentum & collisions
Answer: ΔK = 129067 J
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Common velocity
v′ = m1·v1/(m1 + m2) = 800·22/2400 = 7.333 m/s
Kinetic energy before and after
Kbefore = ½·800·22² = 193600 J
Kafter = ½·2400·7.333² = 64533 J
Energy lost
ΔK = 193600 − 64533 = 129067 J
Answer
ΔK = 129067 J
The lost energy goes into deformation, heat and sound.
10.Momentum & collisions
Answer: θ = 32.22 °
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Momentum components
px = 1500·11 = 16500 kg·m/s
py = 1300·8 = 10400 kg·m/s
Direction
tan θ = py/px = 0.6303 → θ = 32.22°
Answer
θ = 32.22°
11.Hydrostatic force
Answer: F = 119.6 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 2 + 2.5/2 = 3.25 m
A = H·b = 2.5·1.5 = 3.75 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·3.25·3.75 = 119.6 kN
Answer
F = 119.6 kN
12.Hydrostatic force
Answer: ycp = 3.889 m
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 2.5 + 2.5/2 = 3.75 m
A = H·b = 2.5·1 = 2.5 m²
Resultant force
F = ρ·g·yc·A = 880·9.81·3.75·2.5 = 80.93 kN
Centre of pressure
Pressure grows with depth, so the resultant acts below the centroid.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Continuity
v1 = v2·(150/200)² = 0.5625·v2
Bernoulli between inlet and throat
The pipe is horizontal, so only pressure and velocity change.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Pressure difference from the manometer
Δp = (13600 − 1000)·9.81·0.36 = 44498 Pa
Throat velocity
Continuity and Bernoulli together give the ideal throat velocity.
Combined gas law: for a fixed amount of ideal gas, P1V1/T1 = P2V2/T2.
Absolute temperatures
T1 = 303.1 K, T2 = 433.1 K
Combined gas law
V2 = V1·(P1/P2)·(T2/T1) = 5·(150/200)·(433.1/303.1) = 5.358 L
Answer
V2 = 5.358 L
17.Heat engines & refrigerators
Answer: Wmax = 1213 kJ
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 750 + 273.15 = 1023 K
TL = 20 + 273.15 = 293.1 K
Carnot efficiency
ηmax = 1 − TL/TH = 1 − 293.1/1023 = 71.35 %
Maximum work
Wmax = ηmax·QH = 0.7135·1700 = 1213 kJ
Answer
Wmax = 1213 kJ
18.Heat engines & refrigerators
Answer: Tm = 370.5 °C
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 1050 + 273.15 = 1323 K
TL = 40 + 273.15 = 313.1 K
Equal efficiencies
1 − Tm/TH = 1 − TL/Tm gives Tm² = TH·TL.
Tm = √(1323·313.1) = 643.7 K = 370.5 °C
Answer
Tm = 370.5 °C
19.Waves, sound & optics
Answer: f′ = 559.2 Hz
Standing waves and the Doppler effect: a string fixed at both ends, or a pipe open at both ends, fits whole half-wavelengths: L = nλ/2, fn = n·v/(2L), n = 1, 2, 3, … A pipe closed at one end has a node at the closed end and an antinode at the open end: L = nλ/4 with odd n only, fn = n·v/(4L). When source or observer move along the line between them, f′ = f·(v ± vo)/(v ∓ vs): use the upper signs for motion towards each other. Two waves of nearly equal frequency beat at |f₁ − f₂|.
Interference and diffraction: light from two slits a distance d apart reaches a point on the screen with a path difference d·sin θ. Bright fringes appear where d·sin θ = mλ (m = 0, ±1, ±2, …). For a screen at distance L ≫ d, the m-th bright fringe is at y = mλL/d and the fringe spacing is Δy = λL/d. A grating with N lines per millimetre has d = 1/N and sharp maxima at d·sin θ = mλ; since sin θ ≤ 1, the highest order is the largest whole number m ≤ d/λ. A single slit of width a has dark fringes at a·sin θ = mλ, m = ±1, ±2, …