Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A car driving at 72 km/h brakes with a constant deceleration of 7 m/s² until it stops. Find the braking distance s.
v₀ = 72 km/ha = −7 m/s²v = 0
s = m
2.KinematicsHard
A ball is thrown straight up at 14 m/s from the edge of a roof 30 m above the ground. Ignore air resistance and use g = 9.81 m/s². Find the greatest height hmax above the ground.
v₀ = 14 m/sh₀ = 30 mg = 9.81 m/s²
hmax = m
3.Newton’s lawsMedium
A 16 kg block slides down a slope at 20° to the horizontal. The coefficient of kinetic friction is 0.3. Use g = 9.81 m/s². Find the acceleration a of the block along the slope.
m = 16 kgθ = 20°μ = 0.3g = 9.81 m/s²
a = m/s²
4.Newton’s lawsHard
A 4 kg block on a ramp at 25° is connected by a light string over a frictionless pulley at the top of the ramp to a hanging 7.5 kg mass. The hanging mass moves down. The coefficient of kinetic friction between block and ramp is 0.1. Use g = 9.81 m/s². Find the tension T in the string.
m1 = 4 kgm2 = 7.5 kgθ = 25°μ = 0.1g = 9.81 m/s²
T = N
5.Projectile motionMedium
A ball is launched from level ground at 40 m/s and must land 130 m away. Ignore air resistance and use g = 9.81 m/s². Find the smaller of the two possible launch angles θ.
v₀ = 40 m/sR = 130 mg = 9.81 m/s²
θ = °
6.Projectile motionHard
A ball is thrown from ground level at 29 m/s and 35° above the horizontal. It lands on the flat roof of a building 7 m high, on its way down. Ignore air resistance and use g = 9.81 m/s². Find the horizontal distance x from the launch point to where it lands.
v₀ = 29 m/sθ = 35°hroof = 7 mg = 9.81 m/s²
x = m
7.Work & energyMedium
A block slides from rest down a slope at 25° to the horizontal. The coefficient of kinetic friction is 0.15. Find its speed v after it has slid 13 m along the slope.
θ = 25°μ = 0.15d = 13 mg = 9.81 m/s²
v = m/s
8.Work & energyHard
A 0.5 kg block is released from rest at height 1 m on a smooth ramp. At the bottom it crosses a rough horizontal strip 4 m long (μ = 0.1) and then runs onto a spring (k = 1500 N/m) on a smooth surface. Find the maximum compression x of the spring.
m = 0.5 kgh = 1 mL = 4 mμ = 0.1k = 1500 N/mg = 9.81 m/s²
x = cm
9.Momentum & collisionsMedium
A 2 kg glider moving at 12 m/s makes a perfectly elastic head-on collision with a 5 kg glider at rest on a frictionless track. Find the velocity v′1 of the first glider after the collision (positive in its original direction).
m1 = 2 kgm2 = 5 kgv1 = 12 m/sv2 = 0
v′1 = m/s
10.Momentum & collisionsHard
A 20 g bullet is fired horizontally into a 1.5 kg block hanging from light strings 1.8 m long, and stays in it. The strings swing out to a largest angle of 10° from the vertical. Use g = 9.81 m/s². Find the speed v of the bullet before impact.
m = 20 gM = 1.5 kgL = 1.8 mθ = 10°g = 9.81 m/s²
v = m/s
11.Hydrostatic forceMedium
A vertical rectangular gate 1.5 m wide sits in the wall of a tank of water, with its top edge 3 m below the surface. Find the resultant hydrostatic force F on the gate.
A vertical rectangular gate 2 m wide sits in the wall of a tank of glycerin, with its top edge 1 m below the surface. Find the depth ycp of the centre of pressure below the surface.
d = 1 mH = 2 mb = 2 mρ = 1260 kg/m³g = 9.81 m/s²
ycp = m
13.Continuity & BernoulliMedium
Water flows through a horizontal venturi meter with an inlet diameter of 300 mm and a throat diameter of 150 mm. The pressure at the inlet is 39 kPa higher than at the throat. Ignoring losses, find the flow rate Q.
Water flows up through a pipe that narrows from 100 mm to 75 mm while rising 5 m. At section 1 the pressure is 380 kPa and the velocity is 1.5 m/s. Ignoring losses, find the pressure p2 at section 2.
A heat engine receives heat from a source at 300 °C and rejects heat to the surroundings at 10 °C. Its actual thermal efficiency is 38%. Find its second-law efficiency ηII, the ratio of the actual efficiency to the Carnot efficiency.
TH = 300 °CTL = 10 °Cη = 38%
ηII = %
18.Heat engines & refrigeratorsHard
A Carnot heat engine receives 200 kW of heat from a source at 500 °C and rejects heat to the surroundings at 25 °C. All of its work drives a Carnot refrigerator that removes heat from a freezer at -5 °C and also rejects heat to the surroundings at 25 °C. Find the rate Q̇L at which heat is removed from the freezer.
TH = 500 °CT0 = 25 °CTL = -5 °CQ̇H = 200 kW
Q̇L = kW
19.Waves, sound & opticsMedium
Light inside a transparent block is totally reflected at the boundary with ethanol (n = 1.36) for every angle of incidence above 35°. Find the refractive index n1 of the block.
θc = 35°n2 = 1.36
n1 =
20.Waves, sound & opticsHard
Two slits 0.4 mm apart are lit with monochromatic light. On a screen 3 m away, bright fringe number 2 lies 7.5 mm from the central fringe. Find the wavelength λ.
d = 0.4 mmL = 3 my2 = 7.5 mmm = 2
λ = nm
3Solutions
1.Kinematics
Answer: s = 28.57 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Units
v₀ = 72/3.6 = 20 m/s
Braking distance
0 = v₀² − 2·a·s → s = v₀²/(2a) = 20²/(2·7) = 28.57 m
Answer
s = 28.57 m
2.Kinematics
Answer: hmax = 39.99 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Rise above the roof
0 = v₀² − 2·g·Δh → Δh = 14²/(2·9.81) = 9.99 m
Height above the ground
hmax = 30 + 9.99 = 39.99 m
Answer
hmax = 39.99 m
3.Newton’s laws
Answer: a = 0.5897 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Forces along the string
m₂·g = 73.58 N
m₁·g·sin θ = 16.58 N
μ·m₁·g·cos θ = 3.556 N
Acceleration of the system
a = (73.58 − 16.58 − 3.556)/11.5 = 4.647 m/s²
Tension from the hanging mass
m2·g − T = m2·a → T = 7.5·(9.81 − 4.647) = 38.73 N
Answer
T = 38.73 N
5.Projectile motion
Answer: θ = 26.43 °
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Range formula
R = v₀²·sin 2θ/g → sin 2θ = 9.81·130/40² = 0.7971
Angle
2θ = 52.85° → θ = 26.43°
Answer
θ = 26.43°
The other solution is 90° − θ = 63.57°.
6.Projectile motion
Answer: x = 68.86 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
vx = 23.76 m/s, vy = 16.63 m/s
Time to land on the roof
Larger root: the ball is descending.
7 = 16.63·t − 4.905·t²
t = (16.63 + √(16.63² − 2·9.81·7))/9.81 = 2.899 s
Horizontal distance
x = vx·t = 23.76·2.899 = 68.86 m
Answer
x = 68.86 m
7.Work & energy
Answer: v = 8.551 m/s
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy balance along the slope
The block drops a height d·sin θ while friction removes μmg·cos θ·d. The mass cancels.
½v² = g·d·(sin θ − μ·cos θ)
v = √(2·9.81·13·(0.4226 − 0.15·0.9063)) = 8.551 m/s
Answer
v = 8.551 m/s
8.Work & energy
Answer: x = 6.264 cm
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy left after the rough strip
The ramp is smooth, so only the strip removes energy.
mgh − μmgL = 4.905·(1 − 0.1·4) = 2.943 J
Maximum compression
½kx² = 2.943 → x = √(2·2.943/1500) = 0.06264 m = 6.264 cm
Answer
x = 6.264 cm
9.Momentum & collisions
Answer: v′1 = −5.143 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Elastic collision with a target at rest
Solving momentum and energy conservation together gives these two results.
v′1 = (2 − 5)/(2 + 5)·12 = −5.143 m/s
v′2 = 2·2/(2 + 5)·12 = 6.857 m/s
Answer
v′1 = −5.143 m/s
The minus sign means the first glider bounces back.
10.Momentum & collisions
Answer: v = 55.67 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Rise of the block
h = L·(1 − cos θ) = 1.8·(1 − cos 10°) = 0.02735 m
Speed after impact
V = √(2·9.81·0.02735) = 0.7325 m/s
Collision
v = (m + M)·V/m = 1.52·0.7325/0.02 = 55.67 m/s
Answer
v = 55.67 m/s
11.Hydrostatic force
Answer: F = 51.5 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 3 + 1/2 = 3.5 m
A = H·b = 1·1.5 = 1.5 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·3.5·1.5 = 51.5 kN
Answer
F = 51.5 kN
12.Hydrostatic force
Answer: ycp = 2.167 m
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 1 + 2/2 = 2 m
A = H·b = 2·2 = 4 m²
Resultant force
F = ρ·g·yc·A = 1260·9.81·2·4 = 98.88 kN
Centre of pressure
Pressure grows with depth, so the resultant acts below the centroid.
Ic = b·H³/12 = 2·2³/12 = 1.333 m⁴
ycp = yc + Ic/(yc·A) = 2 + 1.333/(2·4) = 2.167 m
Answer
ycp = 2.167 m
13.Continuity & Bernoulli
Answer: Q = 161.2 L/s
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Continuity
v1 = v2·(150/300)² = 0.25·v2
Bernoulli between inlet and throat
The pipe is horizontal, so only pressure and velocity change.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Combined gas law: for a fixed amount of ideal gas, P1V1/T1 = P2V2/T2.
Absolute temperatures
T1 = 313.1 K, T2 = 433.1 K
Combined gas law
V2 = V1·(P1/P2)·(T2/T1) = 2·(400/550)·(433.1/313.1) = 2.012 L
Answer
V2 = 2.012 L
17.Heat engines & refrigerators
Answer: ηII = 75.1 %
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 300 + 273.15 = 573.1 K
TL = 10 + 273.15 = 283.1 K
Carnot efficiency
ηCarnot = 1 − 283.1/573.1 = 50.6 %
Second-law efficiency
ηII = η/ηCarnot = 38/50.6 = 75.1 %
Answer
ηII = 75.1 %
18.Heat engines & refrigerators
Answer: Q̇L = 1098 kW
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 500 + 273.15 = 773.1 K
T0 = 25 + 273.15 = 298.1 K
TL = -5 + 273.15 = 268.1 K
Engine work
η = 1 − 298.1/773.1 = 0.6144
Ẇ = 0.6144·200 = 122.9 kW
Heat removed by the refrigerator
COPR = 268.1/(298.1 − 268.1) = 8.938
Q̇L = 8.938·122.9 = 1098 kW
Answer
Q̇L = 1098 kW
19.Waves, sound & optics
Answer: n1 = 2.371
Geometric optics: at a boundary, n₁·sin θ₁ = n₂·sin θ₂ (Snell's law), with angles measured from the normal and n = c/v. Going into a slower medium the ray bends towards the normal. From a denser medium (n₁ > n₂) beyond the critical angle θc = arcsin(n₂/n₁) all light is reflected: total internal reflection. Thin lenses and spherical mirrors obey 1/f = 1/do + 1/di with the magnification m = −di/do. Sign convention: f > 0 for a converging lens and a concave mirror (f = R/2), f < 0 for a diverging lens and a convex mirror; di > 0 for a real image, di < 0 for a virtual one, and m < 0 for an inverted image.
Refractive index of the block
n₁ = n₂/sin θc = 1.36/0.5736 = 2.371
Answer
n1 = 2.371
20.Waves, sound & optics
Answer: λ = 500 nm
Interference and diffraction: light from two slits a distance d apart reaches a point on the screen with a path difference d·sin θ. Bright fringes appear where d·sin θ = mλ (m = 0, ±1, ±2, …). For a screen at distance L ≫ d, the m-th bright fringe is at y = mλL/d and the fringe spacing is Δy = λL/d. A grating with N lines per millimetre has d = 1/N and sharp maxima at d·sin θ = mλ; since sin θ ≤ 1, the highest order is the largest whole number m ≤ d/λ. A single slit of width a has dark fringes at a·sin θ = mλ, m = ±1, ±2, …