Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A plane starts from rest and accelerates uniformly at 2.75 m/s² along a runway. Find its speed v after 1000 m.
v₀ = 0a = 2.75 m/s²s = 1000 m
v = m/s
2.KinematicsHard
A ball is thrown straight up at 17 m/s from the edge of a roof 20 m above the ground. Ignore air resistance and use g = 9.81 m/s². How long after the throw does it hit the ground? Find t.
v₀ = 17 m/sh₀ = 20 mg = 9.81 m/s²
t = s
3.Newton’s lawsMedium
An 11 kg block slides down a slope at 40° to the horizontal. The coefficient of kinetic friction is 0.3. Use g = 9.81 m/s². Find the acceleration a of the block along the slope.
m = 11 kgθ = 40°μ = 0.3g = 9.81 m/s²
a = m/s²
4.Newton’s lawsHard
A 4 kg block on a ramp at 35° is connected by a light string over a frictionless pulley at the top of the ramp to a hanging 6.5 kg mass. The hanging mass moves down. The coefficient of kinetic friction between block and ramp is 0.25. Use g = 9.81 m/s². Find the acceleration a of the system.
m1 = 4 kgm2 = 6.5 kgθ = 35°μ = 0.25g = 9.81 m/s²
a = m/s²
5.Projectile motionMedium
A ball is kicked from level ground at 26 m/s and 35° above the horizontal towards a wall 45 m away. Ignore air resistance and use g = 9.81 m/s². At what height y does the ball pass the wall?
v₀ = 26 m/sθ = 35°x = 45 mg = 9.81 m/s²
y = m
6.Projectile motionHard
A ball is launched at 40° above horizontal from the top of a 35 m cliff. Ignore air resistance. Find the horizontal distance x travelled before the ball hits the ground.
v0 = 18 m/sθ = 40°h = 35 mg = 9.81 m/s²
x = m
7.Work & energyMedium
A 2 kg block slides 14 m down a slope at 35° to the horizontal, with a coefficient of kinetic friction of 0.35. Find the work Wf done against friction.
m = 2 kgθ = 35°μ = 0.35d = 14 mg = 9.81 m/s²
Wf = J
8.Work & energyHard
A 0.5 kg block is released from rest at height 4 m on a smooth ramp. At the bottom it crosses a rough horizontal strip 3 m long (μ = 0.15) and then runs onto a spring (k = 2000 N/m) on a smooth surface. Find the maximum compression x of the spring.
m = 0.5 kgh = 4 mL = 3 mμ = 0.15k = 2000 N/mg = 9.81 m/s²
x = cm
9.Momentum & collisionsMedium
A 1300 kg car moving at 8 m/s runs into a stationary 600 kg car and the two lock together. How much kinetic energy ΔK is lost in the collision?
m1 = 1300 kgv1 = 8 m/sm2 = 600 kgv2 = 0
ΔK = J
10.Momentum & collisionsHard
A 0.15 kg ball hits a wall at 23 m/s and bounces straight back at 8 m/s. The contact lasts 50 ms. Find the magnitude of the impulse J the wall gives the ball.
m = 0.15 kgvin = 23 m/svout = 8 m/sΔt = 50 ms
J = N·s
11.Hydrostatic forceMedium
A vertical rectangular gate 1.5 m wide sits in the wall of a tank of water, with its top edge 1.5 m below the surface. Find the resultant hydrostatic force F on the gate.
A vertical rectangular gate 1.5 m wide sits in the wall of a tank of water, with its top edge 1.5 m below the surface. Find the depth ycp of the centre of pressure below the surface.
Water drains from a large open tank through a sharp-edged orifice with a diameter of 25 mm. The water level is kept 3.5 m above the orifice and the discharge coefficient is 0.64. Find the flow rate Q. Use g = 9.81 m/s².
d = 25 mmh = 3.5 mCd = 0.64g = 9.81 m/s²
Q = L/s
14.Continuity & BernoulliHard
Water flows up through a pipe that narrows from 100 mm to 75 mm while rising 10 m. At section 1 the pressure is 300 kPa and the velocity is 2.25 m/s. Ignoring losses, find the pressure p2 at section 2.
A heat engine works between a hot reservoir at 350 °C and a cold reservoir at 15 °C. It takes in 3900 kJ of heat. Find the most work Wmax it could possibly produce.
TH = 350 °CTL = 15 °CQH = 3900 kJ
Wmax = kJ
18.Heat engines & refrigeratorsHard
A heat pump delivers 13.5 kW of heat to a heating system at 22 °C, taking heat from a source at 0 °C. Its actual COP is 35% of the Carnot COP between these temperatures. Find the electrical power Ẇ it uses.
TH = 22 °CTL = 0 °CηII = 35%Q̇H = 13.5 kW
Ẇ = kW
19.Waves, sound & opticsMedium
A source of 1000 Hz moves at 25 m/s away from a stationary observer. The speed of sound is 343 m/s. Find the frequency f′ that the observer hears.
f = 1000 Hzv = 343 m/svs = 25 m/s
f′ = Hz
20.Waves, sound & opticsHard
Two slits 0.15 mm apart are lit with monochromatic light. On a screen 2 m away, bright fringe number 3 lies 20 mm from the central fringe. Find the wavelength λ.
d = 0.15 mmL = 2 my3 = 20 mmm = 3
λ = nm
3Solutions
1.Kinematics
Answer: v = 74.16 m/s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Speed after the distance
v = √(2·a·s) = √(2·2.75·1000) = 74.16 m/s
Answer
v = 74.16 m/s
(267 km/h)
2.Kinematics
Answer: t = 4.394 s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Equation of motion
Up is positive and the ground is h₀ below the starting point.
−20 = 17·t − ½·9.81·t²
4.905·t² − 17·t − 20 = 0
Solve the quadratic
Only the positive root is physical.
t = (17 + √(17² + 2·9.81·20))/9.81 = 4.394 s
Answer
t = 4.394 s
3.Newton’s laws
Answer: a = 4.051 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Forces along the string
m₂·g = 63.77 N
m₁·g·sin θ = 22.51 N
μ·m₁·g·cos θ = 8.036 N
Acceleration of the system
a = (63.77 − 22.51 − 8.036)/10.5 = 3.164 m/s²
Answer
a = 3.164 m/s²
5.Projectile motion
Answer: y = 9.612 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Time to the wall
vx = 26·cos 35° = 21.3 m/s
t = x/vx = 45/21.3 = 2.113 s
Height at that time
y = 14.91·2.113 − ½·9.81·2.113² = 9.612 m
Answer
y = 9.612 m
The ball is already on its way down at the wall.
6.Projectile motion
Answer: x = 56.53 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 18·cos 40° = 13.79 m/s
vy = v0·sin θ = 18·sin 40° = 11.57 m/s
Time in the air
Solve y(t) = h + vy·t − ½gt² = 0 for the positive root.
0 = 35 + 11.57·t − 4.905·t²
t = (vy + √(vy² + 2gh))/g = (11.57 + √(133.9 + 686.7))/9.81 = 4.099 s
Horizontal distance
x = vx·t = 13.79·4.099 = 56.53 m
Answer
x = 56.53 m
7.Work & energy
Answer: Wf = 78.75 J
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Friction force
N = mg·cos θ = 19.62·0.8192 = 16.07 N
F = μN = 0.35·16.07 = 5.625 N
Work against friction
Wf = F·d = 5.625·14 = 78.75 J
Answer
Wf = 78.75 J
8.Work & energy
Answer: x = 13.2 cm
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy left after the rough strip
The ramp is smooth, so only the strip removes energy.
mgh − μmgL = 4.905·(4 − 0.15·3) = 17.41 J
Maximum compression
½kx² = 17.41 → x = √(2·17.41/2000) = 0.132 m = 13.2 cm
Answer
x = 13.2 cm
9.Momentum & collisions
Answer: ΔK = 13137 J
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Common velocity
v′ = m1·v1/(m1 + m2) = 1300·8/1900 = 5.474 m/s
Kinetic energy before and after
Kbefore = ½·1300·8² = 41600 J
Kafter = ½·1900·5.474² = 28463 J
Energy lost
ΔK = 41600 − 28463 = 13137 J
Answer
ΔK = 13137 J
The lost energy goes into deformation, heat and sound.
10.Momentum & collisions
Answer: J = 4.65 N·s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Change in momentum
J = m·Δv = 0.15·(8 + 23) = 4.65 N·s
Answer
J = 4.65 N·s
11.Hydrostatic force
Answer: F = 49.66 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 1.5 + 1.5/2 = 2.25 m
A = H·b = 1.5·1.5 = 2.25 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·2.25·2.25 = 49.66 kN
Answer
F = 49.66 kN
12.Hydrostatic force
Answer: ycp = 2.333 m
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 1.5 + 1.5/2 = 2.25 m
A = H·b = 1.5·1.5 = 2.25 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·2.25·2.25 = 49.66 kN
Centre of pressure
Pressure grows with depth, so the resultant acts below the centroid.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Ideal jet velocity
√(2gh) = √(2·9.81·3.5) = 8.287 m/s
Actual flow rate
The discharge coefficient accounts for the contraction of the jet and friction at the edge.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 350 + 273.15 = 623.1 K
TL = 15 + 273.15 = 288.1 K
Carnot efficiency
ηmax = 1 − TL/TH = 1 − 288.1/623.1 = 53.76 %
Maximum work
Wmax = ηmax·QH = 0.5376·3900 = 2097 kJ
Answer
Wmax = 2097 kJ
18.Heat engines & refrigerators
Answer: Ẇ = 2.875 kW
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 22 + 273.15 = 295.1 K
TL = 0 + 273.15 = 273.1 K
Carnot and actual COP
COPmax = 295.1/(295.1 − 273.1) = 13.42
COP = 0.35·13.42 = 4.696
Power input
Ẇ = Q̇H/COP = 13.5/4.696 = 2.875 kW
Answer
Ẇ = 2.875 kW
19.Waves, sound & optics
Answer: f′ = 932.1 Hz
Standing waves and the Doppler effect: a string fixed at both ends, or a pipe open at both ends, fits whole half-wavelengths: L = nλ/2, fn = n·v/(2L), n = 1, 2, 3, … A pipe closed at one end has a node at the closed end and an antinode at the open end: L = nλ/4 with odd n only, fn = n·v/(4L). When source or observer move along the line between them, f′ = f·(v ± vo)/(v ∓ vs): use the upper signs for motion towards each other. Two waves of nearly equal frequency beat at |f₁ − f₂|.
Interference and diffraction: light from two slits a distance d apart reaches a point on the screen with a path difference d·sin θ. Bright fringes appear where d·sin θ = mλ (m = 0, ±1, ±2, …). For a screen at distance L ≫ d, the m-th bright fringe is at y = mλL/d and the fringe spacing is Δy = λL/d. A grating with N lines per millimetre has d = 1/N and sharp maxima at d·sin θ = mλ; since sin θ ≤ 1, the highest order is the largest whole number m ≤ d/λ. A single slit of width a has dark fringes at a·sin θ = mλ, m = ±1, ±2, …