Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A car driving at 90 km/h brakes with a constant deceleration of 4.5 m/s² until it stops. Find the braking distance s.
v₀ = 90 km/ha = −4.5 m/s²v = 0
s = m
2.KinematicsHard
A model rocket is launched straight up from rest. Its engine gives it a constant upward acceleration of 34 m/s² for 3 s, after which the engine stops and the rocket moves freely. Ignore air resistance and use g = 9.81 m/s². How long after launch does it hit the ground? Find t.
a = 34 m/s²t1 = 3 sg = 9.81 m/s²
t = s
3.Newton’s lawsMedium
A 9 kg block slides down a slope at 40° to the horizontal. The coefficient of kinetic friction is 0.2. Use g = 9.81 m/s². Find the acceleration a of the block along the slope.
m = 9 kgθ = 40°μ = 0.2g = 9.81 m/s²
a = m/s²
4.Newton’s lawsHard
A block is given a push so that it starts sliding up a ramp at 30° with a speed of 7.5 m/s. The coefficient of kinetic friction is 0.3. Use g = 9.81 m/s². How far d along the ramp does it slide before it stops?
v₀ = 7.5 m/sθ = 30°μ = 0.3g = 9.81 m/s²
d = m
5.Projectile motionMedium
A ball is launched from level ground at 25° above the horizontal and lands 55 m away. Ignore air resistance and use g = 9.81 m/s². Find the launch speed v0.
θ = 25°R = 55 mg = 9.81 m/s²
v0 = m/s
6.Projectile motionHard
A ball is thrown from ground level at 40 m/s and 30° above the horizontal. It lands on the flat roof of a building 6 m high, on its way down. Ignore air resistance and use g = 9.81 m/s². Find the horizontal distance x from the launch point to where it lands.
v₀ = 40 m/sθ = 30°hroof = 6 mg = 9.81 m/s²
x = m
7.Work & energyMedium
A 4 kg block slides 5 m down a slope at 25° to the horizontal, with a coefficient of kinetic friction of 0.25. Find the work Wf done against friction.
m = 4 kgθ = 25°μ = 0.25d = 5 mg = 9.81 m/s²
Wf = J
8.Work & energyHard
A 0.5 kg block is released from rest at height 4 m on a smooth ramp. At the bottom it crosses a rough horizontal strip 1.5 m long (μ = 0.2) and then runs onto a spring (k = 4000 N/m) on a smooth surface. Find the speed v of the block when it reaches the spring.
m = 0.5 kgh = 4 mL = 1.5 mμ = 0.2k = 4000 N/mg = 9.81 m/s²
v = m/s
9.Momentum & collisionsMedium
A 4 kg projectile moving horizontally at 9 m/s explodes into two fragments that move along the same line. The 3 kg fragment continues forwards at 28 m/s. Find the velocity v′2 of the 1 kg fragment (positive in the original direction).
M = 4 kgu = 9 m/sm1 = 3 kgv′1 = 28 m/sm2 = 1 kg
v′2 = m/s
10.Momentum & collisionsHard
A 0.55 kg ball hits a wall at 12 m/s and bounces straight back at 13 m/s. The contact lasts 25 ms. Find the average force Favg of the wall on the ball.
m = 0.55 kgvin = 12 m/svout = 13 m/sΔt = 25 ms
Favg = N
11.Hydrostatic forceMedium
A vertical rectangular gate 3 m wide sits in the wall of a tank of water, with its top edge 4 m below the surface. Find the resultant hydrostatic force F on the gate.
d = 4 mH = 3 mb = 3 mρ = 1000 kg/m³g = 9.81 m/s²
F = kN
12.Hydrostatic forceHard
A vertical rectangular gate 1 m wide sits in the wall of a tank of seawater, with its top edge 3 m below the surface. Find the resultant hydrostatic force F on the gate.
d = 3 mH = 2 mb = 1 mρ = 1025 kg/m³g = 9.81 m/s²
F = kN
13.Continuity & BernoulliMedium
Water drains from a large open tank through a sharp-edged orifice with a diameter of 40 mm. The water level is kept 4 m above the orifice and the discharge coefficient is 0.61. Find the flow rate Q. Use g = 9.81 m/s².
d = 40 mmh = 4 mCd = 0.61g = 9.81 m/s²
Q = L/s
14.Continuity & BernoulliHard
Water flows up through a pipe that narrows from 100 mm to 50 mm while rising 8 m. At section 1 the pressure is 280 kPa and the velocity is 0.5 m/s. Ignoring losses, find the pressure p2 at section 2.
A heat engine works between a hot reservoir at 700 °C and a cold reservoir at 10 °C. Find the highest possible thermal efficiency ηmax.
TH = 700 °CTL = 10 °C
ηmax = %
18.Heat engines & refrigeratorsHard
Two Carnot engines work in series. Engine A receives heat from a reservoir at 1050 °C and rejects heat to an intermediate reservoir at temperature Tm. Engine B takes all that heat and rejects heat to a reservoir at 40 °C. Both engines produce the same work. Find Tm in °C.
TH = 1050 °CTL = 40 °C
Tm = °C
19.Waves, sound & opticsMedium
Light travels in crown glass (n = 1.50) towards a flat boundary with air (n = 1.00). Find the critical angle θc beyond which it is totally reflected.
n1 = 1.50n2 = 1.00
θc = °
20.Waves, sound & opticsHard
Light of wavelength 650 nm falls on two slits 0.15 mm apart. The screen is 1.2 m away. Find the distance y5 from the central bright fringe to bright fringe number 5.
λ = 650 nmd = 0.15 mmL = 1.2 mm = 5
y5 = mm
3Solutions
1.Kinematics
Answer: s = 69.44 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Units
v₀ = 90/3.6 = 25 m/s
Braking distance
0 = v₀² − 2·a·s → s = v₀²/(2a) = 25²/(2·4.5) = 69.44 m
Answer
s = 69.44 m
2.Kinematics
Answer: t = 25.2 s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Powered phase
v₁ = 34·3 = 102 m/s
h₁ = ½·34·3² = 153 m
Free flight to the ground
Solve −h₁ = v₁·t₂ − ½·g·t₂² for the positive root.
t₂ = (102 + √(102² + 2·9.81·153))/9.81 = 22.2 s
t = 3 + 22.2 = 25.2 s
Answer
t = 25.2 s
3.Newton’s laws
Answer: a = 4.803 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Deceleration
Both forces point down the slope; the mass cancels.
a = 9.81·(sin 30° + 0.3·cos 30°) = 7.454 m/s²
Distance
d = v₀²/(2a) = 7.5²/(2·7.454) = 3.773 m
Answer
d = 3.773 m
5.Projectile motion
Answer: v0 = 26.54 m/s
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Solve the range formula for v₀
v₀ = √(g·R/sin 2θ) = √(9.81·55/sin 50°) = 26.54 m/s
Answer
v0 = 26.54 m/s
6.Projectile motion
Answer: x = 130 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
vx = 34.64 m/s, vy = 20 m/s
Time to land on the roof
Larger root: the ball is descending.
6 = 20·t − 4.905·t²
t = (20 + √(20² − 2·9.81·6))/9.81 = 3.751 s
Horizontal distance
x = vx·t = 34.64·3.751 = 130 m
Answer
x = 130 m
7.Work & energy
Answer: Wf = 44.45 J
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Friction force
N = mg·cos θ = 39.24·0.9063 = 35.56 N
F = μN = 0.25·35.56 = 8.891 N
Work against friction
Wf = F·d = 8.891·5 = 44.45 J
Answer
Wf = 44.45 J
8.Work & energy
Answer: v = 8.52 m/s
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy left after the rough strip
The ramp is smooth, so only the strip removes energy.
mgh − μmgL = 4.905·(4 − 0.2·1.5) = 18.15 J
Speed at the spring
½mv² = mg(h − μL) → v = √(2g(h − μL)) = √(2·9.81·3.7) = 8.52 m/s
Answer
v = 8.52 m/s
9.Momentum & collisions
Answer: v′2 = −48 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Momentum before
p = M·u = 4·9 = 36 kg·m/s
Momentum after
36 = 3·28 + 1·v′2
v′2 = (36 − 84)/1 = −48 m/s
Answer
v′2 = −48 m/s
The minus sign means the second fragment flies backwards.
10.Momentum & collisions
Answer: Favg = 550 N
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Change in momentum
J = m·Δv = 0.55·(13 + 12) = 13.75 N·s
Average force
Favg = J/Δt = 13.75/0.025 = 550 N
Answer
Favg = 550 N
11.Hydrostatic force
Answer: F = 485.6 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 4 + 3/2 = 5.5 m
A = H·b = 3·3 = 9 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·5.5·9 = 485.6 kN
Answer
F = 485.6 kN
12.Hydrostatic force
Answer: F = 80.44 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 3 + 2/2 = 4 m
A = H·b = 2·1 = 2 m²
Resultant force
F = ρ·g·yc·A = 1025·9.81·4·2 = 80.44 kN
Answer
F = 80.44 kN
13.Continuity & Bernoulli
Answer: Q = 6.791 L/s
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Ideal jet velocity
√(2gh) = √(2·9.81·4) = 8.859 m/s
Actual flow rate
The discharge coefficient accounts for the contraction of the jet and friction at the edge.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Combined gas law: for a fixed amount of ideal gas, P1V1/T1 = P2V2/T2.
Absolute temperatures
T1 = 313.1 K, T2 = 443.1 K
Combined gas law
V2 = V1·(P1/P2)·(T2/T1) = 5·(150/250)·(443.1/313.1) = 4.245 L
Answer
V2 = 4.245 L
17.Heat engines & refrigerators
Answer: ηmax = 70.9 %
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 700 + 273.15 = 973.1 K
TL = 10 + 273.15 = 283.1 K
Carnot efficiency
ηmax = 1 − TL/TH = 1 − 283.1/973.1 = 70.9 %
Answer
ηmax = 70.9 %
18.Heat engines & refrigerators
Answer: Tm = 545 °C
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 1050 + 273.15 = 1323 K
TL = 40 + 273.15 = 313.1 K
Equal work
W = Q·(1 − Tlow/Thigh) and Q/T is the same at every reservoir, so W is proportional to the temperature drop.
Tm = (1323 + 313.1)/2 = 818.2 K = 545 °C
Answer
Tm = 545 °C
19.Waves, sound & optics
Answer: θc = 41.81 °
Geometric optics: at a boundary, n₁·sin θ₁ = n₂·sin θ₂ (Snell's law), with angles measured from the normal and n = c/v. Going into a slower medium the ray bends towards the normal. From a denser medium (n₁ > n₂) beyond the critical angle θc = arcsin(n₂/n₁) all light is reflected: total internal reflection. Thin lenses and spherical mirrors obey 1/f = 1/do + 1/di with the magnification m = −di/do. Sign convention: f > 0 for a converging lens and a concave mirror (f = R/2), f < 0 for a diverging lens and a convex mirror; di > 0 for a real image, di < 0 for a virtual one, and m < 0 for an inverted image.
Refraction at 90°
sin θc = n₂/n₁ = 1.00/1.50 = 0.6667
Critical angle
θc = arcsin(0.6667) = 41.81°
Answer
θc = 41.81°
20.Waves, sound & optics
Answer: y5 = 26 mm
Interference and diffraction: light from two slits a distance d apart reaches a point on the screen with a path difference d·sin θ. Bright fringes appear where d·sin θ = mλ (m = 0, ±1, ±2, …). For a screen at distance L ≫ d, the m-th bright fringe is at y = mλL/d and the fringe spacing is Δy = λL/d. A grating with N lines per millimetre has d = 1/N and sharp maxima at d·sin θ = mλ; since sin θ ≤ 1, the highest order is the largest whole number m ≤ d/λ. A single slit of width a has dark fringes at a·sin θ = mλ, m = ±1, ±2, …