Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A plane starts from rest and accelerates uniformly at 1.75 m/s² along a runway. Find its speed v after 1500 m.
v₀ = 0a = 1.75 m/s²s = 1500 m
v = m/s
2.KinematicsHard
A ball is thrown straight up at 17 m/s from the edge of a roof 30 m above the ground. Ignore air resistance and use g = 9.81 m/s². How long after the throw does it hit the ground? Find t.
v₀ = 17 m/sh₀ = 30 mg = 9.81 m/s²
t = s
3.Newton’s lawsMedium
A box slides across a level floor with an initial speed of 11 m/s and comes to rest after 21 m. Use g = 9.81 m/s². Find the coefficient of kinetic friction μ.
v₀ = 11 m/sd = 21 mg = 9.81 m/s²
μ =
4.Newton’s lawsHard
A block is given a push so that it starts sliding up a ramp at 20° with a speed of 5.5 m/s. The coefficient of kinetic friction is 0.15. Use g = 9.81 m/s². How far d along the ramp does it slide before it stops?
v₀ = 5.5 m/sθ = 20°μ = 0.15g = 9.81 m/s²
d = m
5.Projectile motionMedium
A ball is kicked from level ground at 26 m/s and 60° above the horizontal towards a wall 12 m away. Ignore air resistance and use g = 9.81 m/s². At what height y does the ball pass the wall?
v₀ = 26 m/sθ = 60°x = 12 mg = 9.81 m/s²
y = m
6.Projectile motionHard
A ball is launched at 21 m/s and 20° above the horizontal from the top of a 5 m cliff. Ignore air resistance and use g = 9.81 m/s². Find the greatest height H above the ground at the foot of the cliff.
v₀ = 21 m/sθ = 20°h = 5 mg = 9.81 m/s²
H = m
7.Work & energyMedium
A 5 kg block slides 19 m down a slope at 35° to the horizontal, with a coefficient of kinetic friction of 0.3. Find the work Wf done against friction.
m = 5 kgθ = 35°μ = 0.3d = 19 mg = 9.81 m/s²
Wf = J
8.Work & energyHard
A 1 kg block is released from rest at height 1 m on a smooth ramp. At the bottom it crosses a rough horizontal strip 1.5 m long (μ = 0.1) and then runs onto a spring (k = 500 N/m) on a smooth surface. Find the speed v of the block when it reaches the spring.
m = 1 kgh = 1 mL = 1.5 mμ = 0.1k = 500 N/mg = 9.81 m/s²
v = m/s
9.Momentum & collisionsMedium
A 10 g bullet is fired horizontally into a 3 kg wooden block hanging on light strings, and stays inside it. The block swings up until it is 19 cm higher than at the start. Use g = 9.81 m/s². Find the speed v of the bullet before impact.
m = 10 gM = 3 kgh = 19 cmg = 9.81 m/s²
v = m/s
10.Momentum & collisionsHard
A 20 g bullet is fired horizontally into a 2.5 kg block hanging from light strings 0.8 m long, and stays in it. The strings swing out to a largest angle of 20° from the vertical. Use g = 9.81 m/s². Find the speed v of the bullet before impact.
m = 20 gM = 2.5 kgL = 0.8 mθ = 20°g = 9.81 m/s²
v = m/s
11.Hydrostatic forceMedium
A vertical rectangular gate 2 m wide sits in the wall of a tank of water, with its top edge 3 m below the surface. Find the resultant hydrostatic force F on the gate.
A vertical rectangular gate 1.5 m wide sits in the wall of a tank of glycerin, with its top edge 3 m below the surface. Find the resultant hydrostatic force F on the gate.
Water flows through a horizontal pipe that narrows from 100 mm to 50 mm. In the wide section the pressure is 230 kPa and the velocity is 1.25 m/s. Ignoring losses, find the pressure p2 in the narrow section.
Water flows up through a pipe that narrows from 100 mm to 50 mm while rising 8 m. At section 1 the pressure is 390 kPa and the velocity is 0.75 m/s. Ignoring losses, find the pressure p2 at section 2.
A heat engine works between a hot reservoir at 725 °C and a cold reservoir at 15 °C. Find the highest possible thermal efficiency ηmax.
TH = 725 °CTL = 15 °C
ηmax = %
18.Heat engines & refrigeratorsHard
A heat pump delivers 18 kW of heat to a heating system at 22 °C, taking heat from a source at -5 °C. Its actual COP is 30% of the Carnot COP between these temperatures. Find the electrical power Ẇ it uses.
TH = 22 °CTL = -5 °CηII = 30%Q̇H = 18 kW
Ẇ = kW
19.Waves, sound & opticsMedium
Light travels in diamond (n = 2.42) towards a flat boundary with ethanol (n = 1.36). Find the critical angle θc beyond which it is totally reflected.
n1 = 2.42n2 = 1.36
θc = °
20.Waves, sound & opticsHard
Light of wavelength 550 nm falls on two slits 0.4 mm apart. The screen is 1.5 m away. Find the spacing Δy between neighbouring bright fringes.
λ = 550 nmd = 0.4 mmL = 1.5 m
Δy = mm
3Solutions
1.Kinematics
Answer: v = 72.46 m/s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Speed after the distance
v = √(2·a·s) = √(2·1.75·1500) = 72.46 m/s
Answer
v = 72.46 m/s
(260.8 km/h)
2.Kinematics
Answer: t = 4.753 s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Equation of motion
Up is positive and the ground is h₀ below the starting point.
−30 = 17·t − ½·9.81·t²
4.905·t² − 17·t − 30 = 0
Solve the quadratic
Only the positive root is physical.
t = (17 + √(17² + 2·9.81·30))/9.81 = 4.753 s
Answer
t = 4.753 s
3.Newton’s laws
Answer: μ = 0.2937
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Deceleration
a = v₀²/(2d) = 11²/(2·21) = 2.881 m/s²
Friction coefficient
μ·m·g = m·a → μ = a/g = 2.881/9.81 = 0.2937
Answer
μ = 0.2937
4.Newton’s laws
Answer: d = 3.192 m
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Deceleration
Both forces point down the slope; the mass cancels.
a = 9.81·(sin 20° + 0.15·cos 20°) = 4.738 m/s²
Distance
d = v₀²/(2a) = 5.5²/(2·4.738) = 3.192 m
Answer
d = 3.192 m
5.Projectile motion
Answer: y = 16.61 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Time to the wall
vx = 26·cos 60° = 13 m/s
t = x/vx = 12/13 = 0.9231 s
Height at that time
y = 22.52·0.9231 − ½·9.81·0.9231² = 16.61 m
Answer
y = 16.61 m
The ball is still rising at the wall.
6.Projectile motion
Answer: H = 7.629 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Vertical launch speed
vy = 21·sin 20° = 7.182 m/s
Rise above the cliff
Δh = vy²/(2g) = 7.182²/(2·9.81) = 2.629 m
Height above the ground
H = 5 + 2.629 = 7.629 m
Answer
H = 7.629 m
7.Work & energy
Answer: Wf = 229 J
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Friction force
N = mg·cos θ = 49.05·0.8192 = 40.18 N
F = μN = 0.3·40.18 = 12.05 N
Work against friction
Wf = F·d = 12.05·19 = 229 J
Answer
Wf = 229 J
8.Work & energy
Answer: v = 4.084 m/s
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy left after the rough strip
The ramp is smooth, so only the strip removes energy.
mgh − μmgL = 9.81·(1 − 0.1·1.5) = 8.338 J
Speed at the spring
½mv² = mg(h − μL) → v = √(2g(h − μL)) = √(2·9.81·0.85) = 4.084 m/s
Answer
v = 4.084 m/s
9.Momentum & collisions
Answer: v = 581.2 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Swing after impact
V = √(2·g·h) = √(2·9.81·0.19) = 1.931 m/s
Collision
m·v = (m + M)·V → v = (0.01 + 3)·1.931/0.01 = 581.2 m/s
Answer
v = 581.2 m/s
10.Momentum & collisions
Answer: v = 122.6 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Rise of the block
h = L·(1 − cos θ) = 0.8·(1 − cos 20°) = 0.04825 m
Speed after impact
V = √(2·9.81·0.04825) = 0.9729 m/s
Collision
v = (m + M)·V/m = 2.52·0.9729/0.02 = 122.6 m/s
Answer
v = 122.6 m/s
11.Hydrostatic force
Answer: F = 110.4 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 3 + 1.5/2 = 3.75 m
A = H·b = 1.5·2 = 3 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·3.75·3 = 110.4 kN
Answer
F = 110.4 kN
12.Hydrostatic force
Answer: F = 197 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 3 + 2.5/2 = 4.25 m
A = H·b = 2.5·1.5 = 3.75 m²
Resultant force
F = ρ·g·yc·A = 1260·9.81·4.25·3.75 = 197 kN
Answer
F = 197 kN
13.Continuity & Bernoulli
Answer: p2 = 218.3 kPa
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 725 + 273.15 = 998.1 K
TL = 15 + 273.15 = 288.1 K
Carnot efficiency
ηmax = 1 − TL/TH = 1 − 288.1/998.1 = 71.13 %
Answer
ηmax = 71.13 %
18.Heat engines & refrigerators
Answer: Ẇ = 5.489 kW
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 22 + 273.15 = 295.1 K
TL = -5 + 273.15 = 268.1 K
Carnot and actual COP
COPmax = 295.1/(295.1 − 268.1) = 10.93
COP = 0.3·10.93 = 3.279
Power input
Ẇ = Q̇H/COP = 18/3.279 = 5.489 kW
Answer
Ẇ = 5.489 kW
19.Waves, sound & optics
Answer: θc = 34.19 °
Geometric optics: at a boundary, n₁·sin θ₁ = n₂·sin θ₂ (Snell's law), with angles measured from the normal and n = c/v. Going into a slower medium the ray bends towards the normal. From a denser medium (n₁ > n₂) beyond the critical angle θc = arcsin(n₂/n₁) all light is reflected: total internal reflection. Thin lenses and spherical mirrors obey 1/f = 1/do + 1/di with the magnification m = −di/do. Sign convention: f > 0 for a converging lens and a concave mirror (f = R/2), f < 0 for a diverging lens and a convex mirror; di > 0 for a real image, di < 0 for a virtual one, and m < 0 for an inverted image.
Refraction at 90°
sin θc = n₂/n₁ = 1.36/2.42 = 0.562
Critical angle
θc = arcsin(0.562) = 34.19°
Answer
θc = 34.19°
20.Waves, sound & optics
Answer: Δy = 2.063 mm
Interference and diffraction: light from two slits a distance d apart reaches a point on the screen with a path difference d·sin θ. Bright fringes appear where d·sin θ = mλ (m = 0, ±1, ±2, …). For a screen at distance L ≫ d, the m-th bright fringe is at y = mλL/d and the fringe spacing is Δy = λL/d. A grating with N lines per millimetre has d = 1/N and sharp maxima at d·sin θ = mλ; since sin θ ≤ 1, the highest order is the largest whole number m ≤ d/λ. A single slit of width a has dark fringes at a·sin θ = mλ, m = ±1, ±2, …