Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A driver moving at 36 km/h sees an obstacle. Her reaction time is 1.1 s, after which the car brakes with a constant deceleration of 6 m/s². Find the total stopping distance d from the moment she sees the obstacle.
v₀ = 36 km/htr = 1.1 sa = −6 m/s²
d = m
2.KinematicsHard
A model rocket is launched straight up from rest. Its engine gives it a constant upward acceleration of 30 m/s² for 2.5 s, after which the engine stops and the rocket moves freely. Ignore air resistance and use g = 9.81 m/s². Find the greatest height hmax the rocket reaches.
a = 30 m/s²t1 = 2.5 sg = 9.81 m/s²
hmax = m
3.Newton’s lawsMedium
A 20 kg sled is pulled across level snow by a rope at 15° above the horizontal with a force of 80 N. The coefficient of kinetic friction is 0.2. Use g = 9.81 m/s². Find the acceleration a of the sled.
m = 20 kgF = 80 Nθ = 15°μ = 0.2g = 9.81 m/s²
a = m/s²
4.Newton’s lawsHard
A block is given a push so that it starts sliding up a ramp at 25° with a speed of 6.5 m/s. The coefficient of kinetic friction is 0.15. Use g = 9.81 m/s². How far d along the ramp does it slide before it stops?
v₀ = 6.5 m/sθ = 25°μ = 0.15g = 9.81 m/s²
d = m
5.Projectile motionMedium
A ball is launched from level ground at 35° above the horizontal and lands 40 m away. Ignore air resistance and use g = 9.81 m/s². Find the launch speed v0.
θ = 35°R = 40 mg = 9.81 m/s²
v0 = m/s
6.Projectile motionHard
A ball is launched at 30° above horizontal from the top of a 55 m cliff. Ignore air resistance. Find the horizontal distance x travelled before the ball hits the ground.
v0 = 18 m/sθ = 30°h = 55 mg = 9.81 m/s²
x = m
7.Work & energyMedium
A 1200 kg car drives up a 2° slope at a constant 54 km/h. Air resistance and rolling resistance together amount to 200 N. Find the power P the wheels must deliver, in kW.
A 1 kg block is released from rest at height 4 m on a smooth ramp. At the bottom it crosses a rough horizontal strip 4 m long (μ = 0.3) and then runs onto a spring (k = 1500 N/m) on a smooth surface. Find the maximum compression x of the spring.
m = 1 kgh = 4 mL = 4 mμ = 0.3k = 1500 N/mg = 9.81 m/s²
x = cm
9.Momentum & collisionsMedium
A 5 g bullet is fired horizontally into a 4.5 kg wooden block hanging on light strings, and stays inside it. The block swings up until it is 24 cm higher than at the start. Use g = 9.81 m/s². Find the speed v of the bullet before impact.
m = 5 gM = 4.5 kgh = 24 cmg = 9.81 m/s²
v = m/s
10.Momentum & collisionsHard
A 0.3 kg ball hits a wall at 17 m/s and bounces straight back at 20 m/s. The contact lasts 20 ms. Find the magnitude of the impulse J the wall gives the ball.
m = 0.3 kgvin = 17 m/svout = 20 m/sΔt = 20 ms
J = N·s
11.Hydrostatic forceMedium
A vertical rectangular gate 1 m wide sits in the wall of a tank of water, with its top edge 1 m below the surface. Find the resultant hydrostatic force F on the gate.
d = 1 mH = 1 mb = 1 mρ = 1000 kg/m³g = 9.81 m/s²
F = kN
12.Hydrostatic forceHard
A vertical rectangular gate 1 m wide sits in the wall of a tank of glycerin, with its top edge 4 m below the surface. Find the resultant hydrostatic force F on the gate.
d = 4 mH = 2 mb = 1 mρ = 1260 kg/m³g = 9.81 m/s²
F = kN
13.Continuity & BernoulliMedium
Water flows through a horizontal pipe that narrows from 100 mm to 50 mm. In the wide section the pressure is 340 kPa and the velocity is 1.5 m/s. Ignoring losses, find the pressure p2 in the narrow section.
Water flows up through a pipe that narrows from 100 mm to 40 mm while rising 7 m. At section 1 the pressure is 220 kPa and the velocity is 2 m/s. Ignoring losses, find the pressure p2 at section 2.
A heat engine works between a hot reservoir at 275 °C and a cold reservoir at 15 °C. It takes in 2600 kJ of heat. Find the most work Wmax it could possibly produce.
TH = 275 °CTL = 15 °CQH = 2600 kJ
Wmax = kJ
18.Heat engines & refrigeratorsHard
A refrigerator keeps its cold space at 4 °C in a kitchen at 25 °C, removing heat from the cold space at 1 kW. Find the minimum power input Ẇmin.
TH = 25 °CTL = 4 °CQ̇L = 1 kW
Ẇmin = kW
19.Waves, sound & opticsMedium
An object stands 15 cm in front of a thin converging lens with a focal length of 8 cm. Find the magnification m (negative for an inverted image).
do = 15 cmf = 8 cm
m =
20.Waves, sound & opticsHard
Light of wavelength 633 nm falls on two slits 0.2 mm apart. The screen is 2 m away. Find the distance y2 from the central bright fringe to bright fringe number 2.
λ = 633 nmd = 0.2 mmL = 2 mm = 2
y2 = mm
3Solutions
1.Kinematics
Answer: d = 19.33 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Units
v₀ = 36/3.6 = 10 m/s
Reaction distance
d1 = v₀·tr = 10·1.1 = 11 m
Braking distance
d2 = v₀²/(2a) = 10²/(2·6) = 8.333 m
Total
d = 11 + 8.333 = 19.33 m
Answer
d = 19.33 m
2.Kinematics
Answer: hmax = 380.4 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Powered phase
v₁ = 30·2.5 = 75 m/s
h₁ = ½·30·2.5² = 93.75 m
Free flight up
At the top the velocity is zero.
Δh = v₁²/(2g) = 75²/(2·9.81) = 286.7 m
hmax = 93.75 + 286.7 = 380.4 m
Answer
hmax = 380.4 m
3.Newton’s laws
Answer: a = 2.109 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Normal force
N = m·g − F·sin θ = 196.2 − 80·sin 15° = 175.5 N
Horizontal forces
m·a = F·cos θ − μ·N = 77.27 − 35.1
a = 42.18/20 = 2.109 m/s²
Answer
a = 2.109 m/s²
4.Newton’s laws
Answer: d = 3.855 m
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Deceleration
Both forces point down the slope; the mass cancels.
a = 9.81·(sin 25° + 0.15·cos 25°) = 5.48 m/s²
Distance
d = v₀²/(2a) = 6.5²/(2·5.48) = 3.855 m
Answer
d = 3.855 m
5.Projectile motion
Answer: v0 = 20.43 m/s
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Solve the range formula for v₀
v₀ = √(g·R/sin 2θ) = √(9.81·40/sin 70°) = 20.43 m/s
Answer
v0 = 20.43 m/s
6.Projectile motion
Answer: x = 68.42 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 18·cos 30° = 15.59 m/s
vy = v0·sin θ = 18·sin 30° = 9 m/s
Time in the air
Solve y(t) = h + vy·t − ½gt² = 0 for the positive root.
0 = 55 + 9·t − 4.905·t²
t = (vy + √(vy² + 2gh))/g = (9 + √(81 + 1079))/9.81 = 4.389 s
Horizontal distance
x = vx·t = 15.59·4.389 = 68.42 m
Answer
x = 68.42 m
7.Work & energy
Answer: P = 9.163 kW
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d). Power is force times speed: P = F·v.
Driving force
m·g = 1200·9.81 = 11772 N
mg·sin θ = 11772·sin 2° = 410.8 N
F = 410.8 + 200 = 610.8 N
Power
v = 54/3.6 = 15 m/s
P = F·v = 610.8·15 = 9163 W = 9.163 kW
Answer
P = 9.163 kW
8.Work & energy
Answer: x = 19.14 cm
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy left after the rough strip
The ramp is smooth, so only the strip removes energy.
mgh − μmgL = 9.81·(4 − 0.3·4) = 27.47 J
Maximum compression
½kx² = 27.47 → x = √(2·27.47/1500) = 0.1914 m = 19.14 cm
Answer
x = 19.14 cm
9.Momentum & collisions
Answer: v = 1955 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Swing after impact
V = √(2·g·h) = √(2·9.81·0.24) = 2.17 m/s
Collision
m·v = (m + M)·V → v = (0.005 + 4.5)·2.17/0.005 = 1955 m/s
Answer
v = 1955 m/s
10.Momentum & collisions
Answer: J = 11.1 N·s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Change in momentum
J = m·Δv = 0.3·(20 + 17) = 11.1 N·s
Answer
J = 11.1 N·s
11.Hydrostatic force
Answer: F = 14.71 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 1 + 1/2 = 1.5 m
A = H·b = 1·1 = 1 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·1.5·1 = 14.71 kN
Answer
F = 14.71 kN
12.Hydrostatic force
Answer: F = 123.6 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 4 + 2/2 = 5 m
A = H·b = 2·1 = 2 m²
Resultant force
F = ρ·g·yc·A = 1260·9.81·5·2 = 123.6 kN
Answer
F = 123.6 kN
13.Continuity & Bernoulli
Answer: p2 = 323.1 kPa
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Combined gas law: for a fixed amount of ideal gas, P1V1/T1 = P2V2/T2.
Absolute temperatures
T1 = 298.1 K, T2 = 323.1 K
Combined gas law
V2 = V1·(P1/P2)·(T2/T1) = 5·(150/800)·(323.1/298.1) = 1.016 L
Answer
V2 = 1.016 L
17.Heat engines & refrigerators
Answer: Wmax = 1233 kJ
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 275 + 273.15 = 548.1 K
TL = 15 + 273.15 = 288.1 K
Carnot efficiency
ηmax = 1 − TL/TH = 1 − 288.1/548.1 = 47.43 %
Maximum work
Wmax = ηmax·QH = 0.4743·2600 = 1233 kJ
Answer
Wmax = 1233 kJ
18.Heat engines & refrigerators
Answer: Ẇmin = 0.07577 kW
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
The least work is needed by a reversible machine, which has the highest COP.
Ẇmin = Q̇L/COP = 1/13.2 = 0.07577 kW
Answer
Ẇmin = 0.07577 kW
19.Waves, sound & optics
Answer: m = −1.143
Geometric optics: at a boundary, n₁·sin θ₁ = n₂·sin θ₂ (Snell's law), with angles measured from the normal and n = c/v. Going into a slower medium the ray bends towards the normal. From a denser medium (n₁ > n₂) beyond the critical angle θc = arcsin(n₂/n₁) all light is reflected: total internal reflection. Thin lenses and spherical mirrors obey 1/f = 1/do + 1/di with the magnification m = −di/do. Sign convention: f > 0 for a converging lens and a concave mirror (f = R/2), f < 0 for a diverging lens and a convex mirror; di > 0 for a real image, di < 0 for a virtual one, and m < 0 for an inverted image.
Thin-lens equation
1/di = 1/f − 1/do = 1/8 − 1/15
di = 17.14 cm
Magnification
m = −di/do = −17.14/15 = −1.143
Answer
m = −1.143
20.Waves, sound & optics
Answer: y2 = 12.66 mm
Interference and diffraction: light from two slits a distance d apart reaches a point on the screen with a path difference d·sin θ. Bright fringes appear where d·sin θ = mλ (m = 0, ±1, ±2, …). For a screen at distance L ≫ d, the m-th bright fringe is at y = mλL/d and the fringe spacing is Δy = λL/d. A grating with N lines per millimetre has d = 1/N and sharp maxima at d·sin θ = mλ; since sin θ ≤ 1, the highest order is the largest whole number m ≤ d/λ. A single slit of width a has dark fringes at a·sin θ = mλ, m = ±1, ±2, …