Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A driver moving at 100 km/h sees an obstacle. Her reaction time is 0.9 s, after which the car brakes with a constant deceleration of 4.5 m/s². Find the total stopping distance d from the moment she sees the obstacle.
v₀ = 100 km/htr = 0.9 sa = −4.5 m/s²
d = m
2.KinematicsHard
A ball is thrown straight up at 20 m/s from the edge of a roof 30 m above the ground. Ignore air resistance and use g = 9.81 m/s². How long after the throw does it hit the ground? Find t.
v₀ = 20 m/sh₀ = 30 mg = 9.81 m/s²
t = s
3.Newton’s lawsMedium
A box slides across a level floor with an initial speed of 6.5 m/s and comes to rest after 7.2 m. Use g = 9.81 m/s². Find the coefficient of kinetic friction μ.
v₀ = 6.5 m/sd = 7.2 mg = 9.81 m/s²
μ =
4.Newton’s lawsHard
A 1.5 kg block on a horizontal table is connected by a light string over a frictionless pulley to a hanging 5 kg mass. The coefficient of kinetic friction between block and table is 0.3. Use g = 9.81 m/s². Find the tension T in the string.
m1 = 1.5 kgm2 = 5 kgμ = 0.3g = 9.81 m/s²
T = N
5.Projectile motionMedium
A ball is launched from level ground at 34 m/s and must land 45 m away. Ignore air resistance and use g = 9.81 m/s². Find the smaller of the two possible launch angles θ.
v₀ = 34 m/sR = 45 mg = 9.81 m/s²
θ = °
6.Projectile motionHard
A ball is launched at 40° above horizontal from the top of a 5 m cliff. Ignore air resistance. Find the horizontal distance x travelled before the ball hits the ground.
v0 = 16 m/sθ = 40°h = 5 mg = 9.81 m/s²
x = m
7.Work & energyMedium
A block slides from rest down a slope at 35° to the horizontal. The coefficient of kinetic friction is 0.15. Find its speed v after it has slid 4 m along the slope.
θ = 35°μ = 0.15d = 4 mg = 9.81 m/s²
v = m/s
8.Work & energyHard
A 10 kg block is released from rest at height 4 m on a smooth ramp. At the bottom it crosses a rough horizontal strip 1.5 m long (μ = 0.1) and then runs onto a spring (k = 2000 N/m) on a smooth surface. Find the maximum compression x of the spring.
m = 10 kgh = 4 mL = 1.5 mμ = 0.1k = 2000 N/mg = 9.81 m/s²
x = cm
9.Momentum & collisionsMedium
A 2 kg glider moving at 12 m/s makes a perfectly elastic head-on collision with a 0.5 kg glider at rest on a frictionless track. Find the velocity v′1 of the first glider after the collision (positive in its original direction).
m1 = 2 kgm2 = 0.5 kgv1 = 12 m/sv2 = 0
v′1 = m/s
10.Momentum & collisionsHard
A 0.15 kg ball hits a wall at 23 m/s and bounces straight back at 4 m/s. The contact lasts 40 ms. Find the average force Favg of the wall on the ball.
m = 0.15 kgvin = 23 m/svout = 4 m/sΔt = 40 ms
Favg = N
11.Hydrostatic forceMedium
A vertical rectangular gate 1.5 m wide sits in the wall of a tank of water, with its top edge 3 m below the surface. Find the resultant hydrostatic force F on the gate.
A vertical rectangular gate 1 m wide sits in the wall of a tank of glycerin, with its top edge 0.5 m below the surface. Find the resultant hydrostatic force F on the gate.
Water flows through a horizontal pipe that narrows from 75 mm to 40 mm. In the wide section the pressure is 220 kPa and the velocity is 0.5 m/s. Ignoring losses, find the pressure p2 in the narrow section.
Water flows up through a pipe that narrows from 150 mm to 50 mm while rising 7 m. At section 1 the pressure is 200 kPa and the velocity is 1.25 m/s. Ignoring losses, find the pressure p2 at section 2.
A heat engine works between a hot reservoir at 500 °C and a cold reservoir at 30 °C. Find the highest possible thermal efficiency ηmax.
TH = 500 °CTL = 30 °C
ηmax = %
18.Heat engines & refrigeratorsHard
A refrigerator keeps its cold space at -18 °C in a kitchen at 30 °C, removing heat from the cold space at 2.5 kW. Find the minimum power input Ẇmin.
TH = 30 °CTL = -18 °CQ̇L = 2.5 kW
Ẇmin = kW
19.Waves, sound & opticsMedium
An object stands 10 cm in front of a thin diverging lens with a focal length of 25 cm. Find the magnification m (negative for an inverted image).
do = 10 cmf = −25 cm
m =
20.Waves, sound & opticsHard
An optical fibre has a core with n₁ = 1.46 and a cladding with n₂ = 1.41. Find the largest angle θa to the fibre axis at which light from air can enter the end of the fibre and still be guided by total internal reflection.
n1 = 1.46n2 = 1.41n0 = 1.00
θa = °
3Solutions
1.Kinematics
Answer: d = 110.7 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Units
v₀ = 100/3.6 = 27.78 m/s
Reaction distance
d1 = v₀·tr = 27.78·0.9 = 25 m
Braking distance
d2 = v₀²/(2a) = 27.78²/(2·4.5) = 85.73 m
Total
d = 25 + 85.73 = 110.7 m
Answer
d = 110.7 m
2.Kinematics
Answer: t = 5.244 s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Equation of motion
Up is positive and the ground is h₀ below the starting point.
−30 = 20·t − ½·9.81·t²
4.905·t² − 20·t − 30 = 0
Solve the quadratic
Only the positive root is physical.
t = (20 + √(20² + 2·9.81·30))/9.81 = 5.244 s
Answer
t = 5.244 s
3.Newton’s laws
Answer: μ = 0.2991
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Deceleration
a = v₀²/(2d) = 6.5²/(2·7.2) = 2.934 m/s²
Friction coefficient
μ·m·g = m·a → μ = a/g = 2.934/9.81 = 0.2991
Answer
μ = 0.2991
4.Newton’s laws
Answer: T = 14.71 N
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Range formula
R = v₀²·sin 2θ/g → sin 2θ = 9.81·45/34² = 0.3819
Angle
2θ = 22.45° → θ = 11.23°
Answer
θ = 11.23°
The other solution is 90° − θ = 78.77°.
6.Projectile motion
Answer: x = 30.69 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 16·cos 40° = 12.26 m/s
vy = v0·sin θ = 16·sin 40° = 10.28 m/s
Time in the air
Solve y(t) = h + vy·t − ½gt² = 0 for the positive root.
0 = 5 + 10.28·t − 4.905·t²
t = (vy + √(vy² + 2gh))/g = (10.28 + √(105.8 + 98.1))/9.81 = 2.504 s
Horizontal distance
x = vx·t = 12.26·2.504 = 30.69 m
Answer
x = 30.69 m
7.Work & energy
Answer: v = 5.947 m/s
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy balance along the slope
The block drops a height d·sin θ while friction removes μmg·cos θ·d. The mass cancels.
½v² = g·d·(sin θ − μ·cos θ)
v = √(2·9.81·4·(0.5736 − 0.15·0.8192)) = 5.947 m/s
Answer
v = 5.947 m/s
8.Work & energy
Answer: x = 61.46 cm
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy left after the rough strip
The ramp is smooth, so only the strip removes energy.
mgh − μmgL = 98.1·(4 − 0.1·1.5) = 377.7 J
Maximum compression
½kx² = 377.7 → x = √(2·377.7/2000) = 0.6146 m = 61.46 cm
Answer
x = 61.46 cm
9.Momentum & collisions
Answer: v′1 = 7.2 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Elastic collision with a target at rest
Solving momentum and energy conservation together gives these two results.
v′1 = (2 − 0.5)/(2 + 0.5)·12 = 7.2 m/s
v′2 = 2·2/(2 + 0.5)·12 = 19.2 m/s
Answer
v′1 = 7.2 m/s
10.Momentum & collisions
Answer: Favg = 101.3 N
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Change in momentum
J = m·Δv = 0.15·(4 + 23) = 4.05 N·s
Average force
Favg = J/Δt = 4.05/0.04 = 101.3 N
Answer
Favg = 101.3 N
11.Hydrostatic force
Answer: F = 198.7 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 3 + 3/2 = 4.5 m
A = H·b = 3·1.5 = 4.5 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·4.5·4.5 = 198.7 kN
Answer
F = 198.7 kN
12.Hydrostatic force
Answer: F = 54.08 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 0.5 + 2.5/2 = 1.75 m
A = H·b = 2.5·1 = 2.5 m²
Resultant force
F = ρ·g·yc·A = 1260·9.81·1.75·2.5 = 54.08 kN
Answer
F = 54.08 kN
13.Continuity & Bernoulli
Answer: p2 = 218.6 kPa
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Combined gas law: for a fixed amount of ideal gas, P1V1/T1 = P2V2/T2.
Absolute temperatures
T1 = 303.1 K, T2 = 513.1 K
Combined gas law
V2 = V1·(P1/P2)·(T2/T1) = 10·(350/350)·(513.1/303.1) = 16.93 L
Answer
V2 = 16.93 L
17.Heat engines & refrigerators
Answer: ηmax = 60.79 %
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 500 + 273.15 = 773.1 K
TL = 30 + 273.15 = 303.1 K
Carnot efficiency
ηmax = 1 − TL/TH = 1 − 303.1/773.1 = 60.79 %
Answer
ηmax = 60.79 %
18.Heat engines & refrigerators
Answer: Ẇmin = 0.4703 kW
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
The least work is needed by a reversible machine, which has the highest COP.
Ẇmin = Q̇L/COP = 2.5/5.316 = 0.4703 kW
Answer
Ẇmin = 0.4703 kW
19.Waves, sound & optics
Answer: m = 0.7143
Geometric optics: at a boundary, n₁·sin θ₁ = n₂·sin θ₂ (Snell's law), with angles measured from the normal and n = c/v. Going into a slower medium the ray bends towards the normal. From a denser medium (n₁ > n₂) beyond the critical angle θc = arcsin(n₂/n₁) all light is reflected: total internal reflection. Thin lenses and spherical mirrors obey 1/f = 1/do + 1/di with the magnification m = −di/do. Sign convention: f > 0 for a converging lens and a concave mirror (f = R/2), f < 0 for a diverging lens and a convex mirror; di > 0 for a real image, di < 0 for a virtual one, and m < 0 for an inverted image.
Thin-lens equation
1/di = 1/f − 1/do = 1/(−25) − 1/10
di = −7.143 cm
Magnification
m = −di/do = −(−7.143)/10 = 0.7143
Answer
m = 0.7143
20.Waves, sound & optics
Answer: θa = 22.26 °
Geometric optics: at a boundary, n₁·sin θ₁ = n₂·sin θ₂ (Snell's law), with angles measured from the normal and n = c/v. Going into a slower medium the ray bends towards the normal. From a denser medium (n₁ > n₂) beyond the critical angle θc = arcsin(n₂/n₁) all light is reflected: total internal reflection. Thin lenses and spherical mirrors obey 1/f = 1/do + 1/di with the magnification m = −di/do. Sign convention: f > 0 for a converging lens and a concave mirror (f = R/2), f < 0 for a diverging lens and a convex mirror; di > 0 for a real image, di < 0 for a virtual one, and m < 0 for an inverted image.