Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A car driving at 108 km/h brakes with a constant deceleration of 8 m/s² until it stops. How long does braking take? Find t.
v₀ = 108 km/ha = −8 m/s²v = 0
t = s
2.KinematicsHard
A tram starts from rest and accelerates at 2 m/s² for 5 s, then runs at constant speed for 16 s, and finally brakes at 5 m/s² until it stops. Find the total distance s between the two stops.
a1 = 2 m/s²t1 = 5 st2 = 16 sa3 = −5 m/s²
s = m
3.Newton’s lawsMedium
A box slides across a level floor with an initial speed of 2 m/s and comes to rest after 2 m. Use g = 9.81 m/s². Find the coefficient of kinetic friction μ.
v₀ = 2 m/sd = 2 mg = 9.81 m/s²
μ =
4.Newton’s lawsHard
A 4.5 kg block on a horizontal table is connected by a light string over a frictionless pulley to a hanging 1 kg mass. The table is frictionless. Use g = 9.81 m/s². Find the tension T in the string.
m1 = 4.5 kgm2 = 1 kgμ = 0g = 9.81 m/s²
T = N
5.Projectile motionMedium
A ball is launched at 40° above horizontal from level ground. Ignore air resistance. Find the time of flight t until the ball hits the ground.
v0 = 12 m/sθ = 40°g = 9.81 m/s²
t = s
6.Projectile motionHard
A ball is thrown from ground level at 40 m/s and 55° above the horizontal. It lands on the flat roof of a building 21 m high, on its way down. Ignore air resistance and use g = 9.81 m/s². Find the horizontal distance x from the launch point to where it lands.
v₀ = 40 m/sθ = 55°hroof = 21 mg = 9.81 m/s²
x = m
7.Work & energyMedium
A 5 kg block slides 20 m down a slope at 30° to the horizontal, with a coefficient of kinetic friction of 0.4. Find the work Wf done against friction.
m = 5 kgθ = 30°μ = 0.4d = 20 mg = 9.81 m/s²
Wf = J
8.Work & energyHard
A 0.5 kg cart is released from rest at a height of 10.4 m on a smooth track that leads into a vertical circular loop of radius 4 m. Find the normal force N the track exerts on the cart at the top of the loop.
m = 0.5 kgh = 10.4 mR = 4 mg = 9.81 m/s²
N = N
9.Momentum & collisionsMedium
A 4 kg glider moving at 5 m/s makes a perfectly elastic head-on collision with a 1 kg glider at rest on a frictionless track. Find the velocity v′1 of the first glider after the collision (positive in its original direction).
m1 = 4 kgm2 = 1 kgv1 = 5 m/sv2 = 0
v′1 = m/s
10.Momentum & collisionsHard
A 0.55 kg ball hits a wall at 8 m/s and bounces straight back at 17 m/s. The contact lasts 5 ms. Find the average force Favg of the wall on the ball.
m = 0.55 kgvin = 8 m/svout = 17 m/sΔt = 5 ms
Favg = N
11.Hydrostatic forceMedium
A vertical rectangular gate 3 m wide sits in the wall of a tank of water, with its top edge 1 m below the surface. Find the resultant hydrostatic force F on the gate.
d = 1 mH = 2 mb = 3 mρ = 1000 kg/m³g = 9.81 m/s²
F = kN
12.Hydrostatic forceHard
A vertical rectangular gate 2 m wide sits in the wall of a tank of glycerin, with its top edge 3 m below the surface. Find the depth ycp of the centre of pressure below the surface.
d = 3 mH = 2 mb = 2 mρ = 1260 kg/m³g = 9.81 m/s²
ycp = m
13.Continuity & BernoulliMedium
Water flows through a horizontal pipe that narrows from 75 mm to 25 mm. In the wide section the pressure is 270 kPa and the velocity is 1.5 m/s. Ignoring losses, find the pressure p2 in the narrow section.
Water flows up through a pipe that narrows from 100 mm to 50 mm while rising 1 m. At section 1 the pressure is 270 kPa and the velocity is 0.75 m/s. Ignoring losses, find the pressure p2 at section 2.
A heat engine works between a hot reservoir at 400 °C and a cold reservoir at 5 °C. Find the highest possible thermal efficiency ηmax.
TH = 400 °CTL = 5 °C
ηmax = %
18.Heat engines & refrigeratorsHard
A Carnot heat engine receives 160 kW of heat from a source at 800 °C and rejects heat to the surroundings at 27 °C. All of its work drives a Carnot refrigerator that removes heat from a freezer at -15 °C and also rejects heat to the surroundings at 27 °C. Find the rate Q̇L at which heat is removed from the freezer.
TH = 800 °CT0 = 27 °CTL = -15 °CQ̇H = 160 kW
Q̇L = kW
19.Waves, sound & opticsMedium
A source of 1200 Hz moving at 34 m/s and an observer moving at 10 m/s move away from each other. The speed of sound is 343 m/s. Find the frequency f′ that the observer hears.
f = 1200 Hzv = 343 m/svs = 34 m/svo = 10 m/s
f′ = Hz
20.Waves, sound & opticsHard
A grating with 800 lines per millimetre shows the order-1 maximum of a spectral line at 18.9° from the straight-through direction. Find the wavelength λ of the line.
N = 800 mm⁻¹θ1 = 18.9°m = 1
λ = nm
3Solutions
1.Kinematics
Answer: t = 3.75 s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Units
v₀ = 108/3.6 = 30 m/s
Braking time
0 = v₀ − a·t → t = v₀/a = 30/8 = 3.75 s
Answer
t = 3.75 s
2.Kinematics
Answer: s = 195 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Top speed
v = a1·t1 = 2·5 = 10 m/s
Distance of each phase
s1 = ½·2·5² = 25 m
s2 = 10·16 = 160 m
s3 = 10²/(2·5) = 10 m
Total distance
s = 25 + 160 + 10 = 195 m
Answer
s = 195 m
3.Newton’s laws
Answer: μ = 0.1019
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Deceleration
a = v₀²/(2d) = 2²/(2·2) = 1 m/s²
Friction coefficient
μ·m·g = m·a → μ = a/g = 1/9.81 = 0.1019
Answer
μ = 0.1019
4.Newton’s laws
Answer: T = 8.026 N
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 12·cos 40° = 9.193 m/s
vy = v0·sin θ = 12·sin 40° = 7.713 m/s
Time in the air
Starting and landing at the same height: t = 2vy/g.
t = 2·7.713/9.81 = 1.573 s
Answer
t = 1.573 s
6.Projectile motion
Answer: x = 136.8 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
vx = 22.94 m/s, vy = 32.77 m/s
Time to land on the roof
Larger root: the ball is descending.
21 = 32.77·t − 4.905·t²
t = (32.77 + √(32.77² − 2·9.81·21))/9.81 = 5.962 s
Horizontal distance
x = vx·t = 22.94·5.962 = 136.8 m
Answer
x = 136.8 m
7.Work & energy
Answer: Wf = 339.8 J
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Friction force
N = mg·cos θ = 49.05·0.866 = 42.48 N
F = μN = 0.4·42.48 = 16.99 N
Work against friction
Wf = F·d = 16.99·20 = 339.8 J
Answer
Wf = 339.8 J
8.Work & energy
Answer: N = 0.981 N
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d). On a circular path the net force towards the centre must equal mv²/r.
Speed at the top
v² = 2g(h − 2R) = 2·9.81·(10.4 − 8) = 47.09 m²/s²
Forces at the top
m·g = 0.5·9.81 = 4.905 N
N = mv²/R − mg = 0.5·47.09/4 − 4.905 = 0.981 N
Answer
N = 0.981 N
The cart just makes it round when h = 2.5R; then N = 0 at the top.
9.Momentum & collisions
Answer: v′1 = 3 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Elastic collision with a target at rest
Solving momentum and energy conservation together gives these two results.
v′1 = (4 − 1)/(4 + 1)·5 = 3 m/s
v′2 = 2·4/(4 + 1)·5 = 8 m/s
Answer
v′1 = 3 m/s
10.Momentum & collisions
Answer: Favg = 2750 N
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Change in momentum
J = m·Δv = 0.55·(17 + 8) = 13.75 N·s
Average force
Favg = J/Δt = 13.75/0.005 = 2750 N
Answer
Favg = 2750 N
11.Hydrostatic force
Answer: F = 117.7 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 1 + 2/2 = 2 m
A = H·b = 2·3 = 6 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·2·6 = 117.7 kN
Answer
F = 117.7 kN
12.Hydrostatic force
Answer: ycp = 4.083 m
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 3 + 2/2 = 4 m
A = H·b = 2·2 = 4 m²
Resultant force
F = ρ·g·yc·A = 1260·9.81·4·4 = 197.8 kN
Centre of pressure
Pressure grows with depth, so the resultant acts below the centroid.
Ic = b·H³/12 = 2·2³/12 = 1.333 m⁴
ycp = yc + Ic/(yc·A) = 4 + 1.333/(4·4) = 4.083 m
Answer
ycp = 4.083 m
13.Continuity & Bernoulli
Answer: p2 = 180 kPa
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 400 + 273.15 = 673.1 K
TL = 5 + 273.15 = 278.1 K
Carnot efficiency
ηmax = 1 − TL/TH = 1 − 278.1/673.1 = 58.68 %
Answer
ηmax = 58.68 %
18.Heat engines & refrigerators
Answer: Q̇L = 708.4 kW
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 800 + 273.15 = 1073 K
T0 = 27 + 273.15 = 300.1 K
TL = -15 + 273.15 = 258.1 K
Engine work
η = 1 − 300.1/1073 = 0.7203
Ẇ = 0.7203·160 = 115.2 kW
Heat removed by the refrigerator
COPR = 258.1/(300.1 − 258.1) = 6.146
Q̇L = 6.146·115.2 = 708.4 kW
Answer
Q̇L = 708.4 kW
19.Waves, sound & optics
Answer: f′ = 1060 Hz
Standing waves and the Doppler effect: a string fixed at both ends, or a pipe open at both ends, fits whole half-wavelengths: L = nλ/2, fn = n·v/(2L), n = 1, 2, 3, … A pipe closed at one end has a node at the closed end and an antinode at the open end: L = nλ/4 with odd n only, fn = n·v/(4L). When source or observer move along the line between them, f′ = f·(v ± vo)/(v ∓ vs): use the upper signs for motion towards each other. Two waves of nearly equal frequency beat at |f₁ − f₂|.
Interference and diffraction: light from two slits a distance d apart reaches a point on the screen with a path difference d·sin θ. Bright fringes appear where d·sin θ = mλ (m = 0, ±1, ±2, …). For a screen at distance L ≫ d, the m-th bright fringe is at y = mλL/d and the fringe spacing is Δy = λL/d. A grating with N lines per millimetre has d = 1/N and sharp maxima at d·sin θ = mλ; since sin θ ≤ 1, the highest order is the largest whole number m ≤ d/λ. A single slit of width a has dark fringes at a·sin θ = mλ, m = ±1, ±2, …