Power Systems and Electrical Machines: cram pack

Formula sheets, the key method steps for every topic and 10 practice problems, with full solutions at the back.

New problemsBack to the course

In the print window, choose “Save as PDF” to keep a copy on your device.

1Formulas and methods

Three-phase power

Y connection
VL = √3·Vph, IL = Iph
Δ connection
VL = Vph, IL = √3·Iph
Total real power
P = √3·VL·IL·cos φ = 3·Iph²·R
Apparent and reactive power
S = √3·VL·IL, Q = P·tan φ
Correction capacitors
QC = P(tan φ1 − tan φ2), C = QC/(3ωV²)
Voltage across each capacitor
Δ: VL Y: VL/√3
Motor input
Pin = Pout/η

Transformers

Turns ratio
a = N1/N2 = V1/V2
Current ratio
I1/I2 = N2/N1 = 1/a
Rated current
I = S/V
Referred impedance
Z1′ = a²·ZL
Copper loss at part load
Pcu = x²·Pcu,fl
Efficiency
η = x·S·pf/(x·S·pf + Pcore + x²·Pcu,fl)
Maximum efficiency
x = √(Pcore/Pcu,fl)

AC power & power factor

Real power
P = V·I·cos φ
Reactive power
Q = V·I·sin φ
Apparent power
S = V·I = √(P² + Q²)
Power factor
pf = cos φ = P/S
Correction capacitor
QC = P(tan φ1 − tan φ2), C = QC/(ωV²)

AC impedance & phasors

Impedances
ZR = R, ZL = jωL, ZC = 1/(jωC)
Angular frequency
ω = 2πf
Magnitude and angle
|Z| = √(R² + X²), φ = atan(X/R)
Phasor Ohm’s law
V = I·Z

Method

  1. Convert the frequency: ω = 2πf.
  2. Find each reactance: XL = ωL and XC = 1/(ωC).
  3. Add impedances like resistors, with Z = R + jX.
  4. Find the magnitude |Z| = √(R² + X²) and the angle φ = atan(X/R), then use Ohm’s law with phasors.

DC motors

Armature circuit
V = E + IaRa
Back-EMF and torque
E = k·ω, T = k·Ia
Speed
ω = 2π·n/60, ω = (V − IaRa)/k
No-load speed and stall torque
ω0 = V/k, Tstall = k·V/Ra
Powers
Pin = V·Ia, Pdev = E·Ia = T·ω, Pout = Pdev − Prot
Starting
Istart = V/(Ra + Rst)
Speed regulation
SR = (n0 − nFL)/nFL
Maximum developed power
Pmax = V²/(4Ra)
Chopper drive
Va = D·Vdc

Method

  1. Draw the armature circuit: supply V, resistance Ra and the back-EMF E in series.
  2. Use V = E + Ia·Ra to link voltage, current and back-EMF.
  3. Use E = k·ω for speed and T = k·Ia for torque, with ω = 2π·n/60.
  4. For power and efficiency, start from V·Ia, subtract the copper loss Ia²·Ra and then the rotational losses.

2Practice problems

1.Three-phase powerMedium
ABCVL​ = 400 VIL​ = 20 Acos φ = 0.82lagging

A balanced three-phase load draws a line current of 20 A from a supply with a line-to-line voltage of 400 V. The power factor is 0.82 lagging. Find the total real power P drawn by the load in kW.

VL = 400 VIL = 20 Acos φ = 0.82
P = kW
2.Three-phase powerHard
P = 80 kWφ1​S1​Q2​QC​

A balanced three-phase load takes 80 kW at a power factor of 0.7 lagging from a 690 V (line-to-line), 60 Hz supply. A three-phase capacitor bank in parallel with the load must raise the overall power factor to 0.98 lagging. The real power stays the same. The capacitors are connected in Δ. Find the capacitance Cph of each capacitor in µF.

P = 80 kWpf1 = 0.7pf2 = 0.98VL = 690 Vf = 60 Hz
Cph = µF
3.TransformersMedium
11000 V400 VIHV​ = ?ILV​100 kVA

A single-phase 100 kVA, 11000/400 V transformer operates at its rated load. Treat it as ideal. Find the current IHV in the high-voltage winding.

S = 100 kVAV1 = 11000 VV2 = 400 V
IHV = A
4.TransformersHard
50 kVA

A single-phase 50 kVA transformer has a core loss of 300 W and a copper loss of 450 W at rated load. At what load Sη,max, in kVA, is its efficiency highest?

S = 50 kVAPcore = 300 WPcu,fl = 450 W
Sη,max = kVA
5.AC power & power factorMedium
400 V115 kW, 0.7212 kW, 0.8I = ?

Two loads are connected in parallel to a 400 V single-phase supply: a 15 kW load at a power factor of 0.7 lagging and a 12 kW load at a power factor of 0.8 lagging. Find the total current I drawn from the supply.

V = 400 VP1 = 15 kW, pf1 = 0.7 laggingP2 = 12 kW, pf2 = 0.8 lagging
I = A
6.AC power & power factorHard
230 V50 Hzload11 kW, 0.75C68 µFI = ?

A single-phase load takes 11 kW at a power factor of 0.75 lagging from a 230 V, 50 Hz supply. A 68 µF capacitor is connected in parallel with the load. Find the new line current I.

P = 11 kWpf1 = 0.75V = 230 Vf = 50 HzC = 68 µF
I = A
7.AC impedance & phasorsMedium
12 V500 HzR = 100 ΩL = 250 mHC = 22 µF

A series RLC circuit is connected to a 12 V (rms), 500 Hz supply. Find the phase angle φ of the impedance, in degrees (positive when the current lags the voltage).

V = 12 V (rms)f = 500 HzR = 100 ΩL = 250 mHC = 22 µF
φ = °
8.AC impedance & phasorsHard
10 V500 HzR = 25 ΩL = 100 mHC = 2.2 µF

A series RLC circuit is connected to a 10 V (rms), 500 Hz supply. Find the resonant frequency f0 of the circuit.

V = 10 V (rms)f = 500 HzR = 25 ΩL = 100 mHC = 2.2 µF
f0 = Hz
9.DC motorsMedium
T (N·m)n (rpm)3 N·mn0​nFL​

A DC motor (k = 0.3 V·s/rad, Ra = 0.2 Ω) runs from 24 V. At full load it draws 10 A. Neglecting the no-load current, find its speed regulation SR = (n₀ − nFL)/nFL in percent.

V = 24 Vk = 0.3 V·s/radRa = 0.2 ΩIFL = 10 A
SR = %
10.DC motorsHard
+−120 VD = ?Ra​ = 0.5 ΩM+−En = 400 rpmT = 0.32 N·m

A DC chopper feeds a motor (k = 0.08 V·s/rad, Ra = 0.5 Ω) from a 120 V DC bus. The average armature voltage is D·120 V. Find the duty cycle D that runs the motor at 400 rpm with a load of 0.32 N·m.

Vdc = 120 Vk = 0.08 V·s/radRa = 0.5 ΩT = 0.32 N·mn = 400 rpm
D = %

3Solutions

1.Three-phase power

Answer: P = 11.36 kW

Balanced three-phase systems: in a Y (star) connection the line-to-line voltage is √3 times the phase voltage, VL = √3·Vph, and the line current equals the phase current. In a Δ (delta) connection the line-to-line voltage equals the phase voltage and the line current is √3 times the phase current, IL = √3·Iph. The total power is three times the power of one phase: P = 3·Vph·Iph·cos φ = √3·VL·IL·cos φ.

Apparent power

S = √3·VL·IL = √3·400·20 = 13.86 kVA

Real power

P = S·cos φ = 13.86·0.82 = 11.36 kW

Answer

P = 11.36 kW
2.Three-phase power

Answer: Cph = 121.4 µF

Balanced three-phase systems: in a Y (star) connection the line-to-line voltage is √3 times the phase voltage, VL = √3·Vph, and the line current equals the phase current. In a Δ (delta) connection the line-to-line voltage equals the phase voltage and the line current is √3 times the phase current, IL = √3·Iph. The total power is three times the power of one phase: P = 3·Vph·Iph·cos φ = √3·VL·IL·cos φ. Power factor correction: capacitors supply reactive power locally, QC = P·(tan φ1 − tan φ2). Each of the three capacitors supplies QC/3 = V²·ω·C, where V is the voltage across that capacitor: VL in a Δ bank, VL/√3 in a Y bank.

Reactive power before and after

The real power is unchanged, so each power factor fixes the reactive power: Q = P·tan φ.

Q1 = 80·tan(acos 0.7) = 80·1.02 = 81.62 kvar
Q2 = 80·tan(acos 0.98) = 80·0.2031 = 16.24 kvar

Reactive power from the capacitors

QC = Q1 − Q2 = 65.37 kvar

Capacitance per phase

In a Δ bank each capacitor is connected between two lines.

V = 690 V, ω = 2π·60 = 377 rad/s
Cph = (QC/3)/(ω·V²) = 21791/(377·690²) = 121.4 µF

Answer

Cph = 121.4 µF
3.Transformers

Answer: IHV = 9.091 A

Ideal transformer: the voltages are in the ratio of the turns and the currents in the inverse ratio: V₁/V₂ = N₁/N₂ = a and I₁/I₂ = N₂/N₁ = 1/a, so the power in equals the power out, V₁·I₁ = V₂·I₂. A load impedance Z on the secondary looks like a²·Z from the primary.

Rated current

Both windings carry the same apparent power.

IHV = S/V = 100000/11000 = 9.091 A

Answer

IHV = 9.091 A
4.Transformers

Answer: Sη,max = 40.82 kVA

Transformer losses: the core loss (hysteresis and eddy currents) depends on the voltage and is the same at any load. The copper loss in the windings goes with the current squared, so at a fraction x of rated load it is x²·Pcu,fl. Efficiency η = Pout/(Pout + Pcore + Pcu), with Pout = x·S·pf. The efficiency is highest at the load where the copper loss equals the core loss.

Copper loss equals core loss

x²·450 = 300 → x = √(300/450) = 0.8165

Load at maximum efficiency

Sη,max = x·S = 0.8165·50 = 40.82 kVA

Answer

Sη,max = 40.82 kVA
5.AC power & power factor

Answer: I = 90.82 A

AC power: apparent power S = V·I (VA) splits into real power P = S·cos φ (W), which does useful work, and reactive power Q = S·sin φ (var), which moves back and forth between source and load. The power factor is cos φ. A capacitor in parallel supplies reactive power locally, so the line current drops for the same real power.

Reactive power of each load

A lagging load takes reactive power (Q > 0); a leading load supplies it (Q < 0).

Q1 = 15·tan(arccos 0.7) = 15.3 kvar
Q2 = 12·tan(arccos 0.8) = 9 kvar

Totals

P = 15 + 12 = 27 kW
Q = 15.3 + 9 = 24.3 kvar
S = √(27² + 24.3²) = 36.33 kVA

Total current

I = S/V = 36327/400 = 90.82 A

Answer

I = 90.82 A
6.AC power & power factor

Answer: I = 60.63 A

AC power: apparent power S = V·I (VA) splits into real power P = S·cos φ (W), which does useful work, and reactive power Q = S·sin φ (var), which moves back and forth between source and load. The power factor is cos φ. A capacitor in parallel supplies reactive power locally, so the line current drops for the same real power.

Reactive power before and after

The real power P does not change; only the reactive power drawn from the supply does.

Q1 = 11·tan(arccos 0.75) = 9.701 kvar
QC = V²·2πf·C = 230²·2π·50·68·10⁻⁶ = 1130 var = 1.13 kvar
Q2 = 9.701 − 1.13 = 8.571 kvar

New apparent power

S2 = √(11² + 8.571²) = 13.94 kVA

New line current

I = S2/V = 13945/230 = 60.63 A

Answer

I = 60.63 A
7.AC impedance & phasors

Answer: φ = 82.61 °

AC circuits with phasors: resistors, inductors and capacitors have impedances R, jωL and 1/(jωC), with ω = 2πf. In series, impedances add like resistances, but as complex numbers. Rms current and voltage follow Ohm’s law with |Z|.

Reactances

ω = 2πf = 2π·500 = 3142 rad/s
XL = ωL = 3142·0.25 = 785.4 Ω
XC = 1/(ωC) = 1/(3142·22·10⁻⁶) = 14.47 Ω

Impedance

In series the impedances add as complex numbers: Z = R + j(XL − XC).

|Z| = √(R² + (XL − XC)²) = √(100² + (770.9)²) = 777.4 Ω

Phase angle

φ = arctan((XL − XC)/R) = arctan(770.9/100) = 82.61°

Answer

φ = 82.61°
8.AC impedance & phasors

Answer: f0 = 339.3 Hz

AC circuits with phasors: resistors, inductors and capacitors have impedances R, jωL and 1/(jωC), with ω = 2πf. In series, impedances add like resistances, but as complex numbers. Rms current and voltage follow Ohm’s law with |Z|.

Resonance

At resonance the inductive and capacitive reactances cancel: ωL = 1/(ωC). The supply frequency does not matter.

f0 = 1/(2π√(LC)) = 1/(2π·√(0.1·2.2·10⁻⁶)) = 339.3 Hz

Answer

f0 = 339.3 Hz
9.DC motors

Answer: SR = 9.091 %

DC motor: the armature is a resistance Ra in series with the back-EMF E, so V = E + Ia·Ra. The back-EMF grows with speed, E = k·ω, and the torque with current, T = k·Ia, with the same motor constant k (V·s/rad = N·m/A) in SI units. Convert speeds with ω = 2π·n/60. The developed power is E·Ia = T·ω; the input power is V·Ia, and the copper loss Ia²Ra and the rotational loss make the difference. The speed falls in a straight line with torque, ω = V/k − Ra·T/k², from the no-load speed V/k to zero at the stall torque k·V/Ra. At standstill E = 0, so the starting current V/Ra is large unless a resistor limits it.

No-load and full-load speed

n₀ = 60·24/(2π·0.3) = 763.9 rpm
nFL = 60·(24 − 10·0.2)/(2π·0.3) = 700.3 rpm

Speed regulation

SR = (763.9 − 700.3)/700.3·100 = 9.091 %

Answer

SR = 9.091 %
10.DC motors

Answer: D = 4.459 %

DC motor: the armature is a resistance Ra in series with the back-EMF E, so V = E + Ia·Ra. The back-EMF grows with speed, E = k·ω, and the torque with current, T = k·Ia, with the same motor constant k (V·s/rad = N·m/A) in SI units. Convert speeds with ω = 2π·n/60. The developed power is E·Ia = T·ω; the input power is V·Ia, and the copper loss Ia²Ra and the rotational loss make the difference. The speed falls in a straight line with torque, ω = V/k − Ra·T/k², from the no-load speed V/k to zero at the stall torque k·V/Ra. At standstill E = 0, so the starting current V/Ra is large unless a resistor limits it.

Required armature voltage

Va = 0.08·41.89 + 4·0.5 = 5.351 V

Duty cycle

D = 5.351/120 = 4.459 %

Answer

D = 4.459 %

ExamProblems · examproblems.com/courses/power-systems