Power Systems and Electrical Machines: cram pack

Formula sheets, the key method steps for every topic and 10 practice problems, with full solutions at the back.

New problemsBack to the course

In the print window, choose “Save as PDF” to keep a copy on your device.

1Formulas and methods

Three-phase power

Y connection
VL = √3·Vph, IL = Iph
Δ connection
VL = Vph, IL = √3·Iph
Total real power
P = √3·VL·IL·cos φ = 3·Iph²·R
Apparent and reactive power
S = √3·VL·IL, Q = P·tan φ
Correction capacitors
QC = P(tan φ1 − tan φ2), C = QC/(3ωV²)
Voltage across each capacitor
Δ: VL Y: VL/√3
Motor input
Pin = Pout/η

Transformers

Turns ratio
a = N1/N2 = V1/V2
Current ratio
I1/I2 = N2/N1 = 1/a
Rated current
I = S/V
Referred impedance
Z1′ = a²·ZL
Copper loss at part load
Pcu = x²·Pcu,fl
Efficiency
η = x·S·pf/(x·S·pf + Pcore + x²·Pcu,fl)
Maximum efficiency
x = √(Pcore/Pcu,fl)

AC power & power factor

Real power
P = V·I·cos φ
Reactive power
Q = V·I·sin φ
Apparent power
S = V·I = √(P² + Q²)
Power factor
pf = cos φ = P/S
Correction capacitor
QC = P(tan φ1 − tan φ2), C = QC/(ωV²)

AC impedance & phasors

Impedances
ZR = R, ZL = jωL, ZC = 1/(jωC)
Angular frequency
ω = 2πf
Magnitude and angle
|Z| = √(R² + X²), φ = atan(X/R)
Phasor Ohm’s law
V = I·Z

Method

  1. Convert the frequency: ω = 2πf.
  2. Find each reactance: XL = ωL and XC = 1/(ωC).
  3. Add impedances like resistors, with Z = R + jX.
  4. Find the magnitude |Z| = √(R² + X²) and the angle φ = atan(X/R), then use Ohm’s law with phasors.

DC motors

Armature circuit
V = E + IaRa
Back-EMF and torque
E = k·ω, T = k·Ia
Speed
ω = 2π·n/60, ω = (V − IaRa)/k
No-load speed and stall torque
ω0 = V/k, Tstall = k·V/Ra
Powers
Pin = V·Ia, Pdev = E·Ia = T·ω, Pout = Pdev − Prot
Starting
Istart = V/(Ra + Rst)
Speed regulation
SR = (n0 − nFL)/nFL
Maximum developed power
Pmax = V²/(4Ra)
Chopper drive
Va = D·Vdc

Method

  1. Draw the armature circuit: supply V, resistance Ra and the back-EMF E in series.
  2. Use V = E + Ia·Ra to link voltage, current and back-EMF.
  3. Use E = k·ω for speed and T = k·Ia for torque, with ω = 2π·n/60.
  4. For power and efficiency, start from V·Ia, subtract the copper loss Ia²·Ra and then the rotational losses.

2Practice problems

1.Three-phase powerMedium
ABCVL​ = 690 VIL​ = 10 Acos φ = 0.92lagging

A balanced three-phase load draws a line current of 10 A from a supply with a line-to-line voltage of 690 V. The power factor is 0.92 lagging. Find the total real power P drawn by the load in kW.

VL = 690 VIL = 10 Acos φ = 0.92
P = kW
2.Three-phase powerHard
P = 250 kWφ1​S1​Q2​QC​

A balanced three-phase load takes 250 kW at a power factor of 0.7 lagging from a 415 V (line-to-line), 60 Hz supply. A three-phase capacitor bank in parallel with the load must raise the overall power factor to 0.92 lagging. The real power stays the same. The capacitors are connected in Y. Find the capacitance Cph of each capacitor in µF.

P = 250 kWpf1 = 0.7pf2 = 0.92VL = 415 Vf = 60 Hz
Cph = µF
3.TransformersMedium
4 Ω31

A 4 Ω resistor is connected across the secondary winding of an ideal transformer with a turns ratio N₁:N₂ = 3:1. Find the resistance R1′ seen looking into the primary winding.

N1:N2 = 3:1RL = 4 Ω
R1′ = Ω
4.TransformersHard
pf 0.9100 kVA, η = 98.5%

A single-phase 100 kVA transformer has a core loss of 500 W. At rated load and a power factor of 0.9 lagging its efficiency is 98.5%. Find the full-load copper loss Pcu,fl in watts.

S = 100 kVAPcore = 500 Wpf = 0.9η = 98.5%
Pcu,fl = W
5.AC power & power factorMedium
P = 19 kWQSφ

A single-phase motor takes 19 kW at a power factor of 0.7 lagging from a 240 V supply. Find the line current I.

P = 19 kWpf = 0.7V = 240 V
I = A
6.AC power & power factorHard
100 V1000 HzRs​ = 5 ΩXs​ = j15 ΩZL​ = ?

A 100 V (rms), 1000 Hz source has an internal impedance Zs = 5 + j15 Ω. The load impedance ZL can be chosen freely. Find the maximum real power Pmax that can be delivered to the load.

Vs = 100 V (rms)f = 1000 HzZs = 5 + j15 Ω
Pmax = W
7.AC impedance & phasorsMedium
10 V60 HzR = 10 ΩL = 250 mHC = 100 µFI

A series RLC circuit is connected to a 10 V (rms), 60 Hz supply. Find the rms current I.

V = 10 V (rms)f = 60 HzR = 10 ΩL = 250 mHC = 100 µF
I = A
8.AC impedance & phasorsHard
10 V100 HzR = 15 ΩL = 50 mHC = 10 µF

A series RLC circuit is connected to a 10 V (rms), 100 Hz supply. Find the resonant frequency f0 of the circuit.

V = 10 V (rms)f = 100 HzR = 15 ΩL = 50 mHC = 10 µF
f0 = Hz
9.DC motorsMedium
+−24 VRa​ = 0.5 ΩIa​ = 2 AM+−EωT

A DC motor draws 2 A from a 24 V supply. Its armature resistance is 0.5 Ω and its rotational (friction, windage and iron) losses are 4 W. Find its efficiency η.

V = 24 VIa = 2 ARa = 0.5 ΩProt = 4 W
η = %
10.DC motorsHard
+−48 VRs​ = ?Ra​ = 0.25 ΩM+−En = 400 rpmT = 8 N·m

A DC motor (k = 0.4 V·s/rad, Ra = 0.25 Ω) on a fixed 48 V supply drives a load of 8 N·m. Find the series resistance Rs that slows it down to 400 rpm.

V = 48 Vk = 0.4 V·s/radRa = 0.25 ΩT = 8 N·mn = 400 rpm
Rs = Ω

3Solutions

1.Three-phase power

Answer: P = 11 kW

Balanced three-phase systems: in a Y (star) connection the line-to-line voltage is √3 times the phase voltage, VL = √3·Vph, and the line current equals the phase current. In a Δ (delta) connection the line-to-line voltage equals the phase voltage and the line current is √3 times the phase current, IL = √3·Iph. The total power is three times the power of one phase: P = 3·Vph·Iph·cos φ = √3·VL·IL·cos φ.

Apparent power

S = √3·VL·IL = √3·690·10 = 11.95 kVA

Real power

P = S·cos φ = 11.95·0.92 = 11 kW

Answer

P = 11 kW
2.Three-phase power

Answer: Cph = 2288 µF

Balanced three-phase systems: in a Y (star) connection the line-to-line voltage is √3 times the phase voltage, VL = √3·Vph, and the line current equals the phase current. In a Δ (delta) connection the line-to-line voltage equals the phase voltage and the line current is √3 times the phase current, IL = √3·Iph. The total power is three times the power of one phase: P = 3·Vph·Iph·cos φ = √3·VL·IL·cos φ. Power factor correction: capacitors supply reactive power locally, QC = P·(tan φ1 − tan φ2). Each of the three capacitors supplies QC/3 = V²·ω·C, where V is the voltage across that capacitor: VL in a Δ bank, VL/√3 in a Y bank.

Reactive power before and after

The real power is unchanged, so each power factor fixes the reactive power: Q = P·tan φ.

Q1 = 250·tan(acos 0.7) = 250·1.02 = 255.1 kvar
Q2 = 250·tan(acos 0.92) = 250·0.426 = 106.5 kvar

Reactive power from the capacitors

QC = Q1 − Q2 = 148.6 kvar

Capacitance per phase

In a Y bank each capacitor is connected between a line and the star point.

V = 415/√3 = 239.6 V, ω = 2π·60 = 377 rad/s
Cph = (QC/3)/(ω·V²) = 49517/(377·239.6²) = 2288 µF

Answer

Cph = 2288 µF
3.Transformers

Answer: R1′ = 36 Ω

Ideal transformer: the voltages are in the ratio of the turns and the currents in the inverse ratio: V₁/V₂ = N₁/N₂ = a and I₁/I₂ = N₂/N₁ = 1/a, so the power in equals the power out, V₁·I₁ = V₂·I₂. A load impedance Z on the secondary looks like a²·Z from the primary.

Referred resistance

The voltage goes up by a and the current down by a, so the ratio V/I goes up by a².

R1′ = a²·RL = 3²·4 = 36 Ω

Answer

R1′ = 36 Ω
4.Transformers

Answer: Pcu,fl = 870.6 W

Transformer losses: the core loss (hysteresis and eddy currents) depends on the voltage and is the same at any load. The copper loss in the windings goes with the current squared, so at a fraction x of rated load it is x²·Pcu,fl. Efficiency η = Pout/(Pout + Pcore + Pcu), with Pout = x·S·pf. The efficiency is highest at the load where the copper loss equals the core loss.

Output and input power

Pout = 100·0.9 = 90 kW
Pin = 90000/0.985 = 91371 W

Total and copper losses

Ploss = 91371 − 90000 = 1371 W
Pcu,fl = 1371 − 500 = 870.6 W

Answer

Pcu,fl = 870.6 W
5.AC power & power factor

Answer: I = 113.1 A

AC power: apparent power S = V·I (VA) splits into real power P = S·cos φ (W), which does useful work, and reactive power Q = S·sin φ (var), which moves back and forth between source and load. The power factor is cos φ. A capacitor in parallel supplies reactive power locally, so the line current drops for the same real power.

Line current

Only the real part of the power does work, so divide by the power factor.

I = P/(V·cos φ) = 19000/(240·0.7) = 113.1 A

Answer

I = 113.1 A
6.AC power & power factor

Answer: Pmax = 500 W

AC power: apparent power S = V·I (VA) splits into real power P = S·cos φ (W), which does useful work, and reactive power Q = S·sin φ (var), which moves back and forth between source and load. The power factor is cos φ. A capacitor in parallel supplies reactive power locally, so the line current drops for the same real power.

Conjugate match

The load reactance cancels the source reactance, and the load resistance equals the source resistance.

ZL = Zs* = 5 − j15 Ω

Maximum power

I = Vs/(2Rs) = 100/10 = 10 A
Pmax = I²·RL = Vs²/(4Rs) = 100²/(4·5) = 500 W

Answer

Pmax = 500 W
7.AC impedance & phasors

Answer: I = 0.1461 A

AC circuits with phasors: resistors, inductors and capacitors have impedances R, jωL and 1/(jωC), with ω = 2πf. In series, impedances add like resistances, but as complex numbers. Rms current and voltage follow Ohm’s law with |Z|.

Reactances

ω = 2πf = 2π·60 = 377 rad/s
XL = ωL = 377·0.25 = 94.25 Ω
XC = 1/(ωC) = 1/(377·100·10⁻⁶) = 26.53 Ω

Impedance

In series the impedances add as complex numbers: Z = R + j(XL − XC).

|Z| = √(R² + (XL − XC)²) = √(10² + (67.72)²) = 68.46 Ω

Current

The same current flows through every element of a series circuit.

I = V/|Z| = 10/68.46 = 0.1461 A

Answer

I = 0.1461 A
8.AC impedance & phasors

Answer: f0 = 225.1 Hz

AC circuits with phasors: resistors, inductors and capacitors have impedances R, jωL and 1/(jωC), with ω = 2πf. In series, impedances add like resistances, but as complex numbers. Rms current and voltage follow Ohm’s law with |Z|.

Resonance

At resonance the inductive and capacitive reactances cancel: ωL = 1/(ωC). The supply frequency does not matter.

f0 = 1/(2π√(LC)) = 1/(2π·√(0.05·10·10⁻⁶)) = 225.1 Hz

Answer

f0 = 225.1 Hz
9.DC motors

Answer: η = 87.5 %

DC motor: the armature is a resistance Ra in series with the back-EMF E, so V = E + Ia·Ra. The back-EMF grows with speed, E = k·ω, and the torque with current, T = k·Ia, with the same motor constant k (V·s/rad = N·m/A) in SI units. Convert speeds with ω = 2π·n/60. The developed power is E·Ia = T·ω; the input power is V·Ia, and the copper loss Ia²Ra and the rotational loss make the difference. The speed falls in a straight line with torque, ω = V/k − Ra·T/k², from the no-load speed V/k to zero at the stall torque k·V/Ra. At standstill E = 0, so the starting current V/Ra is large unless a resistor limits it.

Powers

Pin = 24·2 = 48 W
Pdev = 23·2 = 46 W
Pout = 46 − 4 = 42 W

Efficiency

η = 42/48·100 = 87.5 %

Answer

η = 87.5 %
10.DC motors

Answer: Rs = 1.312 Ω

DC motor: the armature is a resistance Ra in series with the back-EMF E, so V = E + Ia·Ra. The back-EMF grows with speed, E = k·ω, and the torque with current, T = k·Ia, with the same motor constant k (V·s/rad = N·m/A) in SI units. Convert speeds with ω = 2π·n/60. The developed power is E·Ia = T·ω; the input power is V·Ia, and the copper loss Ia²Ra and the rotational loss make the difference. The speed falls in a straight line with torque, ω = V/k − Ra·T/k², from the no-load speed V/k to zero at the stall torque k·V/Ra. At standstill E = 0, so the starting current V/Ra is large unless a resistor limits it.

Current and back-EMF

Ia = 8/0.4 = 20 A
E = 0.4·41.89 = 16.76 V

Series resistance

Ra + Rs = (48 − 16.76)/20 = 1.562 Ω
Rs = 1.312 Ω

Answer

Rs = 1.312 Ω

The resistor wastes 524.9 W; a chopper controls the speed with far less loss.

ExamProblems · examproblems.com/courses/power-systems