Statics: cram pack

Formula sheets, the key method steps for every topic and 12 practice problems, with full solutions at the back.

New problemsBack to the course

In the print window, choose “Save as PDF” to keep a copy on your device.

1Formulas and methods

Vectors: dot & cross product

Magnitude
|a| = √(ax² + ay² + az²)
Unit vector
û = a/|a|
Components from an angle
Fx = F·cos θ, Fy = F·sin θ
Dot product
a·b = axbx + ayby + azbz = |a||b|cos θ
Scalar projection of a onto b
a·b/|b|
Work
W = F·d
Cross product
a × b = (aybz − azby, azbx − axbz, axby − aybx)
Areas
parallelogram |a × b|, triangle ½|a × b|
Moment about O
MO = r × F, r = A − O
Volume of a parallelepiped
V = |a·(b × c)|

Method

  1. Write every vector in components; for a force given by a magnitude and an angle, use F·cos θ and F·sin θ.
  2. For lengths and directions use the magnitude √(x² + y² + z²) and the unit vector a/|a|.
  3. Use the dot product for angles, projections, perpendicularity and work: a·b = |a||b|cos θ.
  4. Use the cross product for perpendicular vectors, areas and moments: write the three components carefully, keeping the order a × b.

Beam support reactions

Equilibrium
ΣFx = 0, ΣFy = 0, ΣM = 0
Uniform load
resultant w·L at the middle of the load
Moment
M = F·d

Method

  1. Draw a free-body diagram and replace each support by its reactions.
  2. Replace every distributed load by a single force at its centroid.
  3. Take moments about one support to find the reaction at the other.
  4. Use ΣFy = 0 to find the remaining reaction, and check with a second moment equation.

Truss: method of joints

Method of joints
ΣFx = 0, ΣFy = 0 at each joint
Method of sections
ΣM = 0 about a cut point
Member force
positive = tension, negative = compression

Method

  1. Find the support reactions for the whole truss.
  2. Method of joints: start at a joint with at most two unknown member forces and use ΣFx = 0 and ΣFy = 0.
  3. Method of sections: cut through the member you need and take moments about a point where the other unknown members meet.
  4. Assume tension; a negative answer means compression.

Frames & machines

Equilibrium of each member
ΣFx = 0, ΣFy = 0, ΣM = 0
Two-force member
force along the line through its two pins
Pin force
equal and opposite on the two members it joins
Magnitude of a pin force
F = √(Fx² + Fy²)
Lever, pliers, bell crank
Fin·a = Fout·b
Toggle
Flink = F/(2 sin θ), Q = F/(2 tan θ)
Uniform load
resultant w·L at the middle of the load

Method

  1. Draw the whole structure and find the support reactions if there are no more than three unknowns.
  2. Spot the two-force members: loaded only at two pins, their force acts along the line between the pins.
  3. Take the frame apart and draw every member on its own, with equal and opposite pin forces where members meet.
  4. For each member, take moments about a pin with unknown forces, then use ΣFx = 0 and ΣFy = 0; combine components into a magnitude at the end.

Shear force & bending moment

Shear and moment
V = ΣF on one side, M = ΣF·d on one side
Bending stress
σ = M·y/I
Rectangle
I = bh³/12
Section modulus
W = I/ymax
Simply supported, uniform load
Mmax = wL²/8

Method

  1. Find the support reactions from equilibrium of the whole beam.
  2. Cut the beam at the section you need and keep one side.
  3. Shear force: sum of the vertical forces on that side. Bending moment: sum of their moments about the cut.
  4. For the maximum moment, find where the shear force is zero.

Centroid & second moment of area

Centroid
ȳ = ΣAiyi/ΣAi
Rectangle
I = bh³/12
Parallel-axis theorem
I = Ic + A·d²
Composite section
I = Σ(Ic,i + Aidi²)

2Practice problems

1.Vectors: dot & cross productMedium
xyzab

Find the scalar projection compb a of a = (5, 6, −6) onto b = (4, 1, −6), that is, the component of a in the direction of b.

a = (5, 6, −6)b = (4, 1, −6)
compb a =
2.Vectors: dot & cross productHard
xyzabc

Find the volume V of the parallelepiped whose edges from one corner are a = (4, 3, 1), b = (−3, 2, 2) and c = (4, 5, 4).

a = (4, 3, 1)b = (−3, 2, 2)c = (4, 5, 4)
V =
3.Beam support reactionsMedium
P1​ = 50 kNP2​ = 10 kNABRA​ = ?RB​2.5 m0.5 m3 m

The simply supported beam has a pin at A and a roller at B. Find the vertical support reaction RA.

L = 6 mP1 = 50 kN at 2.5 mP2 = 10 kN at 3 m
RA = kN
4.Beam support reactionsHard
w = 3 kN/mP = 10 kNABCRB​ = ?1.5 m1.5 m0.5 m1.5 m

The beam has a pin at A and a roller at B, 3.5 m from A, and overhangs B to the free end C. It carries a point load P at 1.5 m from A and a uniformly distributed load w from 3 m to the free end at 5 m. Find the vertical reaction RB, taking upward as positive.

AB = 3.5 mAC = 5 mP = 10 kN at 1.5 mw = 3 kN/m from 3 to 5 m
RB = kN
5.Truss: method of jointsMedium
ABBCACACB25 kN8 m1 m3 m

Use the method of joints to find the force FBC in member BC. Give tension as positive and compression as negative.

span = 8 mheight = 3 mB is 1 m from Avertical load = 25 kN
FBC = kN
6.Truss: method of jointsHard
ABBCACACB30 kN30 kN5 m3 m3 m

Use the method of joints to find the force FAB in member AB. Give tension as positive and compression as negative.

span = 5 mheight = 3 mB is 3 m from Avertical load = 30 kNhorizontal load = 30 kN →
FAB = kN
7.Frames & machinesMedium
OAB80 NQ100 mm120 mmFO​ = ?

The bell crank shown turns about the pin O. A vertical force of 80 N at A (100 mm from O) is balanced by a horizontal force at B (120 mm above O). Find the magnitude of the pin reaction FO.

F = 80 NOA = 100 mmOB = 120 mm
FO = N
8.Frames & machinesHard
20 kN2.4 m1.2 m2.4 mABCDE

The A-frame shown stands on a pin at A and a roller at B, 2.4 m apart. The legs meet at the pin C, 3.6 m high, and are tied by the horizontal bar DE at 1.2 m. A horizontal force of 20 kN to the right acts at C. Find the tension T in the tie.

P = 20 kNAB = 2.4 mheight of C = 3.6 mheight of DE = 1.2 m
T = kN
9.Shear force & bending momentMedium
w = 4 kN/mABsection2 m8 m

Find the bending moment Mx at the section x = 2 m from support A. Use sagging moments positive and upward shear on the left face positive.

L = 10 mw = 4 kN/m from 0 to 10 mx = 2 m
Mx = kN·m
10.Shear force & bending momentHard
6 kN/m20 kN20 kNABCDEFG1 m1 m1 m1 m1 m1 m

The marks A to G split the beam into six equal parts. At which mark is the bending moment largest in size, sagging or hogging? Click it in the diagram.

20 kN @ 6 m20 kN @ 1 m6 kN/m, 0–4 m
  1. 1A (x = 0 m)
  2. 2B (x = 1 m)
  3. 3C (x = 2 m)
  4. 4D (x = 3 m)
  5. 5E (x = 4 m)
  6. 6F (x = 5 m)
  7. 7G (x = 6 m)
11.Centroid & second moment of areaMedium
200 mm150 mm97.5 mmØ30xIx​ = ?

A 200 mm × 150 mm plate has a circular hole of diameter 30 mm on its vertical centre line, with its centre 97.5 mm above the bottom. Find the second moment of area Ix about the horizontal axis through the centroid.

b = 200 mmh = 150 mmd = 30 mmhole centre: y = 97.5 mm
Ix = × 10⁶ mm⁴
12.Centroid & second moment of areaHard
200 mm240 mm84 mm60 × 30xIx​ = ?

A 200 mm × 240 mm plate has a rectangular cut-out 60 mm wide and 30 mm high, centred on the vertical centre line with its centre 84 mm above the bottom. Find the second moment of area Ix about the horizontal axis through the centroid.

b = 200 mmh = 240 mmcut-out: 60 × 30 mmhole centre: y = 84 mm
Ix = × 10⁶ mm⁴

3Solutions

1.Vectors: dot & cross product

Answer: compb a = 8.516

Dot product: a·b = axbx + ayby + azbz = |a|·|b|·cos θ, a scalar. It gives the angle between two vectors, cos θ = a·b/(|a|·|b|), and it is zero when they are perpendicular. The scalar projection of a onto b is a·b/|b|, and a constant force F moving through a displacement d does work W = F·d.

Dot product

a·b = 5·4 + 6·1 + (−6)·(−6) = 62

Length of b

|b| = √(4² + 1² + (−6)²) = 7.28

Scalar projection

compb a = a·b/|b| = 62/7.28 = 8.516

Answer

compb a = 8.516
2.Vectors: dot & cross product

Answer: V = 29

Cross product: a × b = (aybz − azby, azbx − axbz, axby − aybx) is perpendicular to both vectors, and |a × b| = |a|·|b|·sin θ is the area of the parallelogram they span (the triangle has half of it). Order matters: b × a = −(a × b). The moment of a force F applied at point A about point O is MO = r × F, with r = A − O.

Cross product b × c

(b × c)x = bycz − bzcy = 2·4 − 2·5 = −2
(b × c)y = bzcx − bxcz = 2·4 − (−3)·4 = 20
(b × c)z = bxcy − bycx = (−3)·5 − 2·4 = −23

Dot product with a

a·(b × c) = 4·(−2) + 3·20 + 1·(−23) = 29
V = |29| = 29

Answer

V = 29
3.Beam support reactions

Answer: RA = 34.17 kN

Static equilibrium: a body at rest has ΣFx = 0, ΣFy = 0 and ΣM = 0 about any point. Taking moments about one support removes that support’s reaction from the equation.

P1​ = 50 kNP2​ = 10 kNABRA​RB​2.5 m0.5 m3 m

Free-body diagram

Replace the supports with reaction forces. A roller gives one vertical reaction; with only vertical loads the pin gives one vertical reaction too.

Equilibrium

Moments about A, counter-clockwise positive. Then vertical force balance.

ΣMA = 0: RB·6 = 50·2.5 + 10·3
RB = 155/6 = 25.83 kN
ΣFy = 0: RA = 60 − 25.83 = 34.17 kN

Answer

RA = 34.17 kN
4.Beam support reactions

Answer: RB = 11.14 kN

Static equilibrium: a body at rest has ΣFx = 0, ΣFy = 0 and ΣM = 0 about any point. Replace each distributed load by its resultant (its area) acting at the centroid of the load diagram, and take moments about a support to remove that support’s reaction from the equation.

Resultant of the distributed load

W = 3·2 = 6 kN, x̄ = (3 + 5)/2 = 4 m

Equilibrium

Moments about A, counter-clockwise positive. Then vertical force balance.

ΣMA = 0: RB·3.5 = 10·1.5 + 6·4
RB = 39/3.5 = 11.14 kN
RA = 16 − 11.14 = 4.857 kN

Answer

RB = 11.14 kN
5.Truss: method of joints

Answer: FBC = −7.933 kN

Method of joints: every pin of a truss is in equilibrium, so ΣFx = 0 and ΣFy = 0 at each joint. Start at a joint with at most two unknown member forces. A negative result means the member is in compression.

ABBCACACB25 kNAy​Cy​

Support reactions

Equilibrium of the whole truss. Moments about A, counter-clockwise positive.

ΣMA = 0: Cy·8 = 25·1 → Cy = 3.125 kN
ΣFy = 0: Ay = 25 − 3.125 = 21.88 kN

Joint C

The roller gives only a vertical reaction, so joint C has just two unknown member forces. Assume both in tension.

sin γ = 3/7.616 = 0.3939, cos γ = 7/7.616 = 0.9191
ΣFy = 0: Cy + FBC·sin γ = 0 → FBC = −3.125/0.3939 = −7.933 kN

Answer

FBC = −7.933 kN (compression)
6.Truss: method of joints

Answer: FAB = 8.485 kN

Method of joints: every pin of a truss is in equilibrium, so ΣFx = 0 and ΣFy = 0 at each joint. Start at a joint with at most two unknown member forces. A negative result means the member is in compression.

ABBCACACB30 kN30 kNAy​Cy​Ax​

Support reactions

Equilibrium of the whole truss. Moments about A, counter-clockwise positive.

ΣMA = 0: Cy·5 = 30·3 + 30·3 → Cy = 36 kN
ΣFy = 0: Ay = 30 − 36 = −6 kN
ΣFx = 0: Ax = −30 kN

Joint A

Assume every member is in tension (pulling away from the joint). Only AB has a vertical component at A.

sin α = 3/4.243 = 0.7071
ΣFy = 0: Ay + FAB·sin α = 0
FAB = −−6/0.7071 = 8.485 kN

Answer

FAB = 8.485 kN (tension)
7.Frames & machines

Answer: FO = 104.1 N

Machines: pliers, levers, linkages and clamps turn an input force into a larger or a differently directed output force. Draw one part as a free body and take moments about its pivot: the pin force drops out, and Fin·a = Fout·b gives the mechanical advantage a/b. The pin force then follows from ΣF = 0 on the same part. In a toggle, two links meet at a shallow angle θ; each link is a two-force member, so a small force F at the joint creates large link forces F/(2 sin θ) and a clamping force F/(2 tan θ).

Force at B

Q = 80·100/120 = 66.67 N

Pin reaction

Ox = 66.67 N, Oy = 80 N
FO = √(66.67² + 80²) = 104.1 N

Answer

FO = 104.1 N
8.Frames & machines

Answer: T = 15 kN

Frames and machines: unlike a truss, a frame contains at least one member that carries forces at more than two points, or a load between its pins. First look for two-force members: a member loaded only at two pins has its force along the line through them, so it adds one unknown, not two. Then use the whole structure for the support reactions when there are no more than three unknowns. Finally take the frame apart: draw each member separately, with the pin forces equal and opposite on the two members they connect, and write ΣFx = 0, ΣFy = 0 and ΣM = 0 for it. Taking moments about a pin removes both components of that pin force from the equation.

Whole frame: moments about A

By·2.4 = 20·3.6
By = 30 kN

Leg BC: moments about C

30·1.2 = T·2.4
T = 15 kN

Answer

T = 15 kN

A positive T means the tie is in tension, as assumed.

9.Shear force & bending moment

Answer: Mx = 32 kN·m

Method of sections: cut the beam where you want the internal forces and keep one side. The shear force V balances the vertical forces on that side, and the bending moment M balances their moments about the cut.

Support reactions

Equilibrium of the whole beam.

UDL resultant: W = w·ℓ = 4·10 = 40 kN, acting at x̄ = 5 m
ΣMA = 0: RB·10 = 4·10·5
RB = 200/10 = 20 kN
ΣFy = 0: RA = 40 − 20 = 20 kN
w = 4 kN/mABRA​ = 20RB​ = 20section2 m8 m

Cut at x = 2 m and keep the left part

Only forces left of the cut appear. A UDL portion acts as one force at the middle of that portion.

M = RA·x − (each load left of the cut × its distance to the cut)
Mx = 20·2 − 4·2·1 = 32 kN·m

Answer

Mx = 32 kN·m
10.Shear force & bending moment

Answer: E (x = 4 m)

Largest bending moment: M changes slope wherever the shear force changes, so its peaks sit where the shear force crosses zero: under a point load, inside a distributed load, or over a support of an overhang. At a fixed support of a cantilever the moment is largest at the wall. Compare the size of M at those places, sagging or hogging.

Support reactions

Take moments about one support, then use the vertical force balance.

R1 = 17 kN, R2 = 47 kN

Bending moment at every mark

Sum the moments of all forces on one side of the cut. Sagging is positive, hogging negative.

MA = 0, MB = 14, MC = 2, MD = −16, ME = −40 kN·m, MF = −20, MG = 0

Answer

Mark E: ME = −40 kN·m
11.Centroid & second moment of area

Answer: Ix = 55.84 × 10⁶ mm⁴

Sections with holes: treat a hole as a negative area. The centroid is ȳ = (A₁y₁ − A₂y₂)/(A₁ − A₂), with A₁, y₁ for the full plate and A₂, y₂ for the hole. For the second moment of area about the centroidal axis, use the parallel-axis theorem for each part and subtract the hole: I = (Ic1 + A₁d₁²) − (Ic2 + A₂d₂²), where d is the distance from each part's own centroid to the axis through ȳ. A rectangle has Ic = bh³/12 and a circle Ic = πd⁴/64.

Centroid

ȳ = (30000·75 − 706.9·97.5)/(30000 − 706.9) = 74.46 mm

Full plate about ȳ

200·150³/12 + 30000·0.5429² = 56.26 × 10⁶ mm⁴

Hole about ȳ

π·30⁴/64 + 706.9·23.04² = 0.4151 × 10⁶ mm⁴

Subtract

Ix = 55.84 × 10⁶ mm⁴

Answer

Ix = 55.84 × 10⁶ mm⁴
12.Centroid & second moment of area

Answer: Ix = 227.8 × 10⁶ mm⁴

Sections with holes: treat a hole as a negative area. The centroid is ȳ = (A₁y₁ − A₂y₂)/(A₁ − A₂), with A₁, y₁ for the full plate and A₂, y₂ for the hole. For the second moment of area about the centroidal axis, use the parallel-axis theorem for each part and subtract the hole: I = (Ic1 + A₁d₁²) − (Ic2 + A₂d₂²), where d is the distance from each part's own centroid to the axis through ȳ. A rectangle has Ic = bh³/12 and a circle Ic = πd⁴/64.

Centroid

ȳ = (48000·120 − 1800·84)/(48000 − 1800) = 121.4 mm

Full plate about ȳ

200·240³/12 + 48000·−1.403² = 230.5 × 10⁶ mm⁴

Hole about ȳ

60·30³/12 + 1800·−37.4² = 2.653 × 10⁶ mm⁴

Subtract

Ix = 227.8 × 10⁶ mm⁴

Answer

Ix = 227.8 × 10⁶ mm⁴

ExamProblems · examproblems.com/courses/statics