Structural Analysis: cram pack

Formula sheets, the key method steps for every topic and 10 practice problems, with full solutions at the back.

New problemsBack to the course

In the print window, choose “Save as PDF” to keep a copy on your device.

1Formulas and methods

Beam support reactions

Equilibrium
ΣFx = 0, ΣFy = 0, ΣM = 0
Uniform load
resultant w·L at the middle of the load
Moment
M = F·d

Method

  1. Draw a free-body diagram and replace each support by its reactions.
  2. Replace every distributed load by a single force at its centroid.
  3. Take moments about one support to find the reaction at the other.
  4. Use ΣFy = 0 to find the remaining reaction, and check with a second moment equation.

Shear force & bending moment

Shear and moment
V = ΣF on one side, M = ΣF·d on one side
Bending stress
σ = M·y/I
Rectangle
I = bh³/12
Section modulus
W = I/ymax
Simply supported, uniform load
Mmax = wL²/8

Method

  1. Find the support reactions from equilibrium of the whole beam.
  2. Cut the beam at the section you need and keep one side.
  3. Shear force: sum of the vertical forces on that side. Bending moment: sum of their moments about the cut.
  4. For the maximum moment, find where the shear force is zero.

Truss: method of joints

Method of joints
ΣFx = 0, ΣFy = 0 at each joint
Method of sections
ΣM = 0 about a cut point
Member force
positive = tension, negative = compression

Method

  1. Find the support reactions for the whole truss.
  2. Method of joints: start at a joint with at most two unknown member forces and use ΣFx = 0 and ΣFy = 0.
  3. Method of sections: cut through the member you need and take moments about a point where the other unknown members meet.
  4. Assume tension; a negative answer means compression.

Beam deflection

Point load at midspan
δ = PL³/(48EI)
Uniform load, simply supported
δ = 5wL⁴/(384EI)
Cantilever, end load
δ = PL³/(3EI)
Cantilever, uniform load
δ = wL⁴/(8EI)
Superposition
δ = δ1 + δ2

Column buckling

Euler load
Pcr = π²EI/(KL)²
Effective length factor
K = 1 pinned–pinned, 0.5 fixed–fixed, 0.7 fixed–pinned, 2 fixed–free
Critical stress
σcr = Pcr/A
Slenderness
λ = KL/r, r = √(I/A)

2Practice problems

1.Beam support reactionsMedium
P = 55 kNM = 10 kN·mABRA​ = ?1.5 m2 m1.5 m

The simply supported beam has a pin at A and a roller at B. It carries a point load P at 1.5 m from A and a counter-clockwise couple M at 3.5 m from A. Find the vertical reaction RA, taking upward as positive.

L = 5 mP = 55 kN at 1.5 mM = 10 kN·m (counter-clockwise) at 3.5 m
RA = kN
2.Beam support reactionsHard
P = 10 kN, 60°Q = 10 kNABα = ?1 m2.5 m2.5 m

The simply supported beam has a pin at A and a roller at B. A load P acts at 1 m from A, inclined at 60° to the horizontal, and a vertical load Q acts at 3.5 m from A. Find the angle α between the total reaction force at the pin A and the horizontal.

L = 6 mP = 10 kN at 1 m, θ = 60°Q = 10 kN at 3.5 m
α = °
3.Shear force & bending momentMedium
15 kN/m30 kNABCDEFG1 m1 m1 m1 m1 m1 m

The marks A to G split the beam into six equal parts. At which mark is the bending moment largest in size, sagging or hogging? Click it in the diagram.

30 kN @ 3 m15 kN/m, 0–6 m
  1. 1A (x = 0 m)
  2. 2B (x = 1 m)
  3. 3C (x = 2 m)
  4. 4D (x = 3 m)
  5. 5E (x = 4 m)
  6. 6F (x = 5 m)
  7. 7G (x = 6 m)
4.Shear force & bending momentHard
w = 8 kN/mP = 75 kNAB3 m7 m

The simply supported beam carries a uniformly distributed load w over its whole span and a point load P. Find the maximum bending moment Mmax in the beam.

L = 10 mP = 75 kN at 3 mw = 8 kN/m from 0 to 10 m
Mmax = kN·m
5.Truss: method of jointsMedium
ABBCACACB25 kN5 m3 m3 m

Use the method of joints to find the force FBC in member BC. Give tension as positive and compression as negative.

span = 5 mheight = 3 mB is 3 m from Avertical load = 25 kN
FBC = kN
6.Truss: method of jointsHard
ABBCACACB55 kN5 kN6 m5 m4 m

Use the method of joints to find the force FBC in member BC. Give tension as positive and compression as negative.

span = 6 mheight = 4 mB is 5 m from Avertical load = 55 kNhorizontal load = 5 kN →
FBC = kN
7.Beam deflectionMedium
P = 12 kNABδ2.5 m1.5 m

A simply supported beam carries a point load P at a = 2.5 m from support A. Find the deflection δP under the load.

P = 12 kNa = 2.5 mL = 4 mE = 200 GPa (steel)I = 36 × 10⁶ mm⁴
δP = mm
8.Beam deflectionHard
P = 75 kNAB3 m3 m

A propped cantilever is fixed at A and simply supported (propped) at B. It carries a point load P at midspan. EI is constant. Find the reaction RB at the prop.

L = 6 mP = 75 kN at 3 m
RB = kN
9.Column bucklingMedium
PL = 3 m50 × 100 mmcross-section

A column of length L made of aluminium is fixed at the base and free at the top. Using Euler’s formula, find its critical buckling load Pcr.

L = 3 mE = 70 GPa (aluminium)b × h = 50 × 100 mm
Pcr = kN
10.Column bucklingHard
P = 135 kNL = 1.5 md = ?cross-section

A solid round column of length L made of steel is fixed at the base and free at the top. It must carry 135 kN with a factor of safety of 2 against buckling. Find the smallest diameter d.

P = 135 kNn = 2L = 1.5 mE = 200 GPa (steel)
d = mm

3Solutions

1.Beam support reactions

Answer: RA = 40.5 kN

Static equilibrium: a body at rest has ΣFx = 0, ΣFy = 0 and ΣM = 0 about any point. Replace each distributed load by its resultant (its area) acting at the centroid of the load diagram, and take moments about a support to remove that support’s reaction from the equation.

Moments about A

Counter-clockwise positive.

ΣMA = 0: RB·5 − 55·1.5 + 10 = 0
RB = 72.5/5 = 14.5 kN

Vertical equilibrium

RA = 55 − 14.5 = 40.5 kN

Answer

RA = 40.5 kN

A negative reaction acts downward.

2.Beam support reactions

Answer: α = 66.29 °

Static equilibrium: a body at rest has ΣFx = 0, ΣFy = 0 and ΣM = 0 about any point. Replace each distributed load by its resultant (its area) acting at the centroid of the load diagram, and take moments about a support to remove that support’s reaction from the equation.

Components of P

Pv = 10·sin 60° = 8.66 kN
Ph = 10·cos 60° = 5 kN

Reactions

ΣMA = 0: RB·6 = 8.66·1 + 10·3.5 → RB = 7.277 kN
Ay = 8.66 + 10 − 7.277 = 11.38 kN
Ax = Ph = 5 kN

Direction at A

α = atan(Ay/Ax) = atan(11.38/5) = 66.29°

Answer

α = 66.29°
3.Shear force & bending moment

Answer: D (x = 3 m)

Largest bending moment: M changes slope wherever the shear force changes, so its peaks sit where the shear force crosses zero: under a point load, inside a distributed load, or over a support of an overhang. At a fixed support of a cantilever the moment is largest at the wall. Compare the size of M at those places, sagging or hogging.

Support reactions

Take moments about one support, then use the vertical force balance.

R1 = 60 kN, R2 = 60 kN

Bending moment at every mark

Sum the moments of all forces on one side of the cut. Sagging is positive, hogging negative.

MA = 0, MB = 52.5, MC = 90, MD = 112.5 kN·m, ME = 90, MF = 52.5, MG = 0

Answer

Mark D: MD = 112.5 kN·m
4.Shear force & bending moment

Answer: Mmax = 241.5 kN·m

Method of sections: cut the beam where you want the internal forces and keep one side. The shear force V balances the vertical forces on that side, and the bending moment M balances their moments about the cut. Maximum moment: since dM/dx = V, the bending moment has its peak where the shear force passes through zero, either at a point load or inside a distributed load.

Support reactions

Equilibrium of the whole beam.

UDL resultant: W = w·ℓ = 8·10 = 80 kN, acting at x̄ = 5 m
ΣMA = 0: RB·10 = 75·3 + 8·10·5
RB = 625/10 = 62.5 kN
ΣFy = 0: RA = 155 − 62.5 = 92.5 kN

Where is V = 0?

V(3⁻) = RA − w·3 = 68.5 kN
V(3⁺) = 68.5 − 75 = −6.5 kN
The shear changes sign at the load, so the maximum is under the load.

Maximum moment

Mmax = RA·3 − w·3²/2 = 92.5·3 − 8·3²/2 = 241.5 kN·m

Answer

Mmax = 241.5 kN·m

It occurs at x = 3 m from A.

5.Truss: method of joints

Answer: FBC = −18.03 kN

Method of joints: every pin of a truss is in equilibrium, so ΣFx = 0 and ΣFy = 0 at each joint. Start at a joint with at most two unknown member forces. A negative result means the member is in compression.

ABBCACACB25 kNAy​Cy​

Support reactions

Equilibrium of the whole truss. Moments about A, counter-clockwise positive.

ΣMA = 0: Cy·5 = 25·3 → Cy = 15 kN
ΣFy = 0: Ay = 25 − 15 = 10 kN

Joint C

The roller gives only a vertical reaction, so joint C has just two unknown member forces. Assume both in tension.

sin γ = 3/3.606 = 0.8321, cos γ = 2/3.606 = 0.5547
ΣFy = 0: Cy + FBC·sin γ = 0 → FBC = −15/0.8321 = −18.03 kN

Answer

FBC = −18.03 kN (compression)
6.Truss: method of joints

Answer: FBC = −50.68 kN

Method of joints: every pin of a truss is in equilibrium, so ΣFx = 0 and ΣFy = 0 at each joint. Start at a joint with at most two unknown member forces. A negative result means the member is in compression.

ABBCACACB55 kN5 kNAy​Cy​Ax​

Support reactions

Equilibrium of the whole truss. Moments about A, counter-clockwise positive.

ΣMA = 0: Cy·6 = 55·5 + 5·4 → Cy = 49.17 kN
ΣFy = 0: Ay = 55 − 49.17 = 5.833 kN
ΣFx = 0: Ax = −5 kN

Joint C

The roller gives only a vertical reaction, so joint C has just two unknown member forces. Assume both in tension.

sin γ = 4/4.123 = 0.9701, cos γ = 1/4.123 = 0.2425
ΣFy = 0: Cy + FBC·sin γ = 0 → FBC = −49.17/0.9701 = −50.68 kN

Answer

FBC = −50.68 kN (compression)
7.Beam deflection

Answer: δP = 1.953 mm

Beam deflection: deflections come from integrating the curvature M/(EI) twice. Standard cases are tabulated, for example PL³/(3EI) for a cantilever with an end load and 5wL⁴/(384EI) for a simply supported beam under a full uniform load. Deflections from separate loads add (superposition).

Consistent units

Work in N and mm: P in N, w in N/mm (kN/m = N/mm), L in mm, E in N/mm² (GPa × 1000), I in mm⁴.

P = 12000 N, a = 2500 mm, b = 1500 mm, L = 4000 mm
EI = 7.2 × 10¹² N·mm²

Deflection under the load

δP = Pa²b²/(3EIL) = 12000·2500²·1500²/(3·7.2 × 10¹²·4000) = 1.953 mm

Answer

δP = 1.953 mm
8.Beam deflection

Answer: RB = 23.44 kN

Beam deflection: deflections come from integrating the curvature M/(EI) twice. Standard cases are tabulated, for example PL³/(3EI) for a cantilever with an end load and 5wL⁴/(384EI) for a simply supported beam under a full uniform load. Deflections from separate loads add (superposition). For a statically indeterminate beam, remove a redundant support and require the deflection there to be zero (compatibility).

Remove the prop

Without the prop the beam is a cantilever. Its free end would deflect under the load.

δload = P(L/2)²(3L − L/2)/(6EI) = 5PL³/(48EI)

Compatibility at the prop

The prop force RB alone lifts the free end by RBL³/(3EI). The prop holds B at zero deflection, so the two must cancel. EI cancels out.

RB·L³/(3EI) = 5PL³/(48EI) → RB = 5P/16 = 5·75/16 = 23.44 kN

Answer

RB = 23.44 kN
9.Column buckling

Answer: Pcr = 19.99 kN

Euler buckling: a slender column becomes unstable at Pcr = π²EI/(KL)², where KL is the effective length: K = 1 for pinned–pinned, 2 for fixed–free, 0.7 for fixed–pinned and 0.5 for fixed–fixed. It buckles about the axis with the smallest I. The formula holds for slender columns, whose critical stress stays below the yield stress.

Smallest second moment of area

A rectangle buckles about its weak axis, using the smaller dimension cubed.

Imin = h·b³/12 = 100·50³/12 = 1.042 × 10⁶ mm⁴

Effective length

KL = 2·3000 = 6000 mm

Critical load

Pcr = π²EI/(KL)² = π²·70000·1.042 × 10⁶/6000² = 19991 N = 19.99 kN

Answer

Pcr = 19.99 kN
10.Column buckling

Answer: d = 70.77 mm

Euler buckling: a slender column becomes unstable at Pcr = π²EI/(KL)², where KL is the effective length: K = 1 for pinned–pinned, 2 for fixed–free, 0.7 for fixed–pinned and 0.5 for fixed–fixed. It buckles about the axis with the smallest I. The formula holds for slender columns, whose critical stress stays below the yield stress.

Required critical load

Pcr = n·P = 2·135000 = 270000 N
KL = 2·1500 = 3000 mm

Solve for the diameter

d = (64·n·P·(KL)²/(π³E))^(1/4) = (64·270000·3000²/(π³·200000))^(1/4) = 70.77 mm

Answer

d = 70.77 mm

Check: the slenderness KL/r is 169.6, so the column is slender and Euler applies.

ExamProblems · examproblems.com/courses/structural-analysis