In the print window, choose “Save as PDF” to keep a copy on your device.
1Formulas and methods
DC motors
Armature circuit
V = E + IaRa
Back-EMF and torque
E = k·ω, T = k·Ia
Speed
ω = 2π·n/60, ω = (V − IaRa)/k
No-load speed and stall torque
ω0 = V/k, Tstall = k·V/Ra
Powers
Pin = V·Ia, Pdev = E·Ia = T·ω, Pout = Pdev − Prot
Starting
Istart = V/(Ra + Rst)
Speed regulation
SR = (n0 − nFL)/nFL
Maximum developed power
Pmax = V²/(4Ra)
Chopper drive
Va = D·Vdc
Method
Draw the armature circuit: supply V, resistance Ra and the back-EMF E in series.
Use V = E + Ia·Ra to link voltage, current and back-EMF.
Use E = k·ω for speed and T = k·Ia for torque, with ω = 2π·n/60.
For power and efficiency, start from V·Ia, subtract the copper loss Ia²·Ra and then the rotational losses.
Gears & gear trains
Meshing gears
n1·N1 = n2·N2
Torque
T2 = T1·(N2/N1)·η
Power
P = T·ω, ω = 2π·n/60
Compound train
total ratio = product of the stage ratios
Data acquisition & sampling
Nyquist criterion
fs > 2·fmax, fN = fs/2
Alias frequency
fa = |f − k·fs|, k = round(f/fs)
Step size
1 LSB = VFSR/2ᴺ
Quantisation error (rounding)
±½ LSB
Truncating ADC code
D = ⌊Vin/LSB⌋
Bits for a resolution r
2ᴺ ≥ span/r
Ideal SQNR, full-scale sine
SQNR = 6.02·N + 1.76 dB
Data rate
channels × fs × N bit/s
Multiplexed ADC
fs = 1/(n·(tc + tset))
UART
Tb = 1/baud; 8N1 = 10 bits per byte; bytes/s = baud/bits per frame
Baud rate divider
baud = fclk/(16·D)
Method
Write down what is given: sampling rate, signal frequencies, number of bits, input range, baud rate.
For sampling questions, compare each frequency with fs/2; a higher frequency appears at fa = |f − k·fs| with the nearest multiple of fs.
For resolution questions, find 1 LSB = VFSR/2ᴺ, or the smallest N with 2ᴺ ≥ span/resolution.
For data rates and UART links, count everything that is sent: channels, samples per second, bits or whole bytes per sample, and the start, parity and stop bits of every frame.
Wheatstone bridge & strain gauges
Divider voltages
Va = VsR2/(R1 + R2), Vb = VsR4/(R3 + R4)
Output
Vab = Va − Vb
Balance
R1/R2 = R3/R4
Slide-wire bridge
R/Rx = l/(100 − l)
Thévenin resistance
Rth = R1∥R2 + R3∥R4
Gauge factor
ΔR/R = GF·ε
Bridge output
quarter Vs·GF·ε/4, half Vs·GF·ε/2, full Vs·GF·ε
Small change, one arm
Vab ≈ Vs·ΔR/(4R)
Stress
σ = E·ε
Method
Treat the bridge as two voltage dividers across the same supply.
For balance, set R₁/R₂ = R₃/R₄ and solve for the unknown resistor.
For an unbalanced bridge, find Va and Vb from the dividers and subtract; use the Thévenin equivalent when a meter loads the output.
For strain gauges, convert strain to ΔR/R = GF·ε and use Vs·GF·ε/4, /2 or ×1 for a quarter, half or full bridge.
Steady-state error & PID control
System type
number of poles of G(s) at s = 0
Error constants
Kp = lim G(s), Kv = lim s·G(s), Ka = lim s²·G(s) (s → 0)
Step A
ess = A/(1 + Kp)
Ramp A·t
ess = A/Kv
Parabola A·t²/2
ess = A/Ka
PID controller
C(s) = Kp + Ki/s + Kd·s
Second-order target
s² + 2ζωns + ωn²
Overshoot and timing
%OS = 100·e−ζπ/√(1−ζ²), tp = π/ωd, ts ≈ 4/(ζωn)
Method
Count the poles of the open loop C(s)·G(s) at s = 0: that is the system type.
Work out the error constant that matches the input: Kp for a step, Kv for a ramp, Ka for a parabola.
Apply ess = A/(1 + Kp), A/Kv or A/Ka, or solve it for the gain you need.
For a damping or speed specification, write the closed-loop characteristic polynomial and match it with s² + 2ζω_n·s + ω_n².
2Practice problems
1.DC motorsMedium
A DC motor (k = 0.6 V·s/rad, Ra = 0.4 Ω) runs from 220 V. At full load it draws 40 A. Neglecting the no-load current, find its speed regulation SR = (n₀ − nFL)/nFL in percent.
V = 220 Vk = 0.6 V·s/radRa = 0.4 ΩIFL = 40 A
SR = %
2.DC motorsHard
A DC chopper feeds a motor (k = 1.5 V·s/rad, Ra = 2 Ω) from a 220 V DC bus. The average armature voltage is D·220 V. Find the duty cycle D that runs the motor at 400 rpm with a load of 9 N·m.
A 7.5 kW motor running at 1450 rpm drives a pinion with 30 teeth and a module of 3 mm. Find the tangential force Ft on the pinion teeth.
P = 7.5 kWn = 1450 rpmN1 = 30m = 3 mm
Ft = N
4.Gears & gear trainsHard
In a compound gear train, gear A (36 teeth) on the input shaft turns at 3000 rpm and drives gear B (60 teeth). Gear C (30 teeth) is fixed to the same shaft as B and drives gear D on the output shaft. The output must turn at 675 rpm. How many teeth ND must gear D have?
nin = 3000 rpmA = 36B = 60C = 30nout = 675 rpm
ND =
5.Data acquisition & samplingMedium
Find the ideal signal-to-quantisation-noise ratio SQNR of a 16-bit ADC for a full-scale sine wave.
N = 16
SQNR = dB
6.Data acquisition & samplingHard
A temperature sensor gives 10 mV/°C (0 V at 0 °C). Its signal is amplified 10 times and fed to a 10-bit ADC with a range of 0 to 3.3 V (1 LSB = VFSR/2ᴺ). Find the temperature change ΔTLSB that corresponds to one LSB.
S = 10 mV/°CG = 10N = 10VFSR = 3.3 V
ΔTLSB = °C
7.Wheatstone bridge & strain gaugesMedium
A galvanometer with a resistance of 50 Ω is connected between a and b of the bridge shown (Vs = 9 V). Find the galvanometer current Ig from a to b, in µA.
A 350 Ω strain gauge with gauge factor 2.12 is bonded to a steel bar. Under load its resistance rises by 0.5565 Ω. Find the strain ε in microstrain (µε).
R = 350 ΩGF = 2.12ΔR = 0.5565 Ω
ε = µε
9.Steady-state error & PID controlMedium
The parabolic input r(t) = 5·t²/2 is applied to a unity-feedback loop with G(s) = 2(s + 1)/(s²(s + 10)). Find the steady-state error ess.
G(s) = 2(s + 1)/(s²(s + 10))r(t) = 5·t²/2
ess =
10.Steady-state error & PID controlHard
A proportional controller K = 8 drives the plant G(s) = 2/(s(s + 6)) in a unity-feedback loop. Find the peak time tp of the step response.
G(s) = 2/(s(s + 6))K = 8
tp = s
11.Step responseMedium
A system has the transfer function G(s) = 164/(s² + 8s + 82) and receives a unit step input. Find the 2 % settling time ts of the step response, using ts ≈ 4/(ζωₙ).
G(s) = 164/(s² + 8s + 82)
ts = s
12.Step responseHard
A unity negative feedback loop has G(s) = K/(s(s + 20)). Find the gain K that gives a step response with 30 % overshoot.
G(s) = K/(s(s + 20))%OS = 30 %
K =
3Solutions
1.DC motors
Answer: SR = 7.843 %
DC motor: the armature is a resistance Ra in series with the back-EMF E, so V = E + Ia·Ra. The back-EMF grows with speed, E = k·ω, and the torque with current, T = k·Ia, with the same motor constant k (V·s/rad = N·m/A) in SI units. Convert speeds with ω = 2π·n/60. The developed power is E·Ia = T·ω; the input power is V·Ia, and the copper loss Ia²Ra and the rotational loss make the difference. The speed falls in a straight line with torque, ω = V/k − Ra·T/k², from the no-load speed V/k to zero at the stall torque k·V/Ra. At standstill E = 0, so the starting current V/Ra is large unless a resistor limits it.
No-load and full-load speed
n₀ = 60·220/(2π·0.6) = 3501 rpm
nFL = 60·(220 − 40·0.4)/(2π·0.6) = 3247 rpm
Speed regulation
SR = (3501 − 3247)/3247·100 = 7.843 %
Answer
SR = 7.843 %
2.DC motors
Answer: D = 34.01 %
DC motor: the armature is a resistance Ra in series with the back-EMF E, so V = E + Ia·Ra. The back-EMF grows with speed, E = k·ω, and the torque with current, T = k·Ia, with the same motor constant k (V·s/rad = N·m/A) in SI units. Convert speeds with ω = 2π·n/60. The developed power is E·Ia = T·ω; the input power is V·Ia, and the copper loss Ia²Ra and the rotational loss make the difference. The speed falls in a straight line with torque, ω = V/k − Ra·T/k², from the no-load speed V/k to zero at the stall torque k·V/Ra. At standstill E = 0, so the starting current V/Ra is large unless a resistor limits it.
Required armature voltage
Va = 1.5·41.89 + 6·2 = 74.83 V
Duty cycle
D = 74.83/220 = 34.01 %
Answer
D = 34.01 %
3.Gears & gear trains
Answer: Ft = 1098 N
Gear geometry: the module m sets the tooth size. A gear with N teeth has a pitch diameter d = m·N, two meshing gears have the same module, and their centre distance is a = (d₁ + d₂)/2 = m·(N₁ + N₂)/2. The pitch-line speed is v = π·d·n/60, and the tangential tooth force follows from the torque: Ft = 2T/d.
Torque on the pinion
ω = 2π·1450/60 = 151.8 rad/s
T = P/ω = 7500/151.8 = 49.39 N·m
Pitch diameter
d = m·N = 3·30 = 90 mm
Tangential force
Ft = 2T/d = 2·49.39/0.09 = 1098 N
Answer
Ft = 1098 N
4.Gears & gear trains
Answer: ND = 80
Gear trains: meshing gears have the same speed at the teeth, so n₁·N₁ = n₂·N₂: the gear with fewer teeth turns faster. Gears on one shaft turn at the same speed. Power is passed on (minus losses), so torque goes up when speed goes down: T₂ = T₁·(N₂/N₁)·η, and P = T·ω with ω = 2π·n/60.
Intermediate shaft speed
nB = nC = 3000·36/60 = 1800 rpm
Teeth on gear D
ND = C·nC/nout = 30·1800/675 = 80
Answer
ND = 80
5.Data acquisition & sampling
Answer: SQNR = 98.08 dB
ADC resolution: an N-bit converter divides its full-scale range VFSR into 2ᴺ codes, from 0 to 2ᴺ − 1. One step is 1 LSB = VFSR/2ᴺ: the smallest change the converter can show. A truncating ADC gives the code ⌊Vin/LSB⌋; a rounding ADC is never more than ½ LSB away from the true value, its quantisation error. Every extra bit halves the LSB and adds about 6 dB to the ideal signal-to-quantisation-noise ratio SQNR = 6.02·N + 1.76 dB for a full-scale sine. To reach a resolution r over a span, choose the smallest N with 2ᴺ ≥ span/r.
Ideal SQNR
SQNR = 6.02·16 + 1.76 = 98.08 dB
Answer
SQNR = 98.08 dB
6.Data acquisition & sampling
Answer: ΔTLSB = 0.03223 °C
ADC resolution: an N-bit converter divides its full-scale range VFSR into 2ᴺ codes, from 0 to 2ᴺ − 1. One step is 1 LSB = VFSR/2ᴺ: the smallest change the converter can show. A truncating ADC gives the code ⌊Vin/LSB⌋; a rounding ADC is never more than ½ LSB away from the true value, its quantisation error. Every extra bit halves the LSB and adds about 6 dB to the ideal signal-to-quantisation-noise ratio SQNR = 6.02·N + 1.76 dB for a full-scale sine. To reach a resolution r over a span, choose the smallest N with 2ᴺ ≥ span/r.
Step size
1 LSB = 3300/1024 = 3.223 mV
Sensitivity at the ADC
10·10 = 100 mV/°C
Temperature resolution
ΔTLSB = 3.223/100 = 0.03223 °C
Answer
ΔTLSB = 0.03223 °C
The ADC reaches full scale at 33 °C.
7.Wheatstone bridge & strain gauges
Answer: Ig = −3576 µA
Wheatstone bridge: two voltage dividers share one supply Vs. The left divider R1–R2 gives Va = Vs·R2/(R1 + R2) and the right divider R3–R4 gives Vb = Vs·R4/(R3 + R4); the output is Vab = Va − Vb. The bridge is balanced (Vab = 0, no current in the meter) when R1/R2 = R3/R4, that is R1·R4 = R2·R3. Seen from the output, the bridge is a Thévenin source with Rth = R1∥R2 + R3∥R4.
Thévenin voltage
Vth = 9·(60/110 − 150/250) = −0.4909 V
Thévenin resistance
Rth = R₁∥R₂ + R₃∥R₄ = 87.27 Ω
Galvanometer current
Ig = −0.4909/(87.27 + 50) = −3576 µA
Answer
Ig = −3576 µA
8.Wheatstone bridge & strain gauges
Answer: ε = 750 µε
Strain gauges: a gauge changes its resistance with strain: ΔR/R = GF·ε, where the gauge factor GF is about 2 for metal foil. In a bridge with all arms equal to R, one active gauge (quarter bridge) gives Vo ≈ Vs·GF·ε/4. Two active gauges with opposite strains in adjacent arms (half bridge) give Vs·GF·ε/2, and four (full bridge) give Vs·GF·ε. Stress follows from Hooke’s law, σ = E·ε. Load cells state their sensitivity in mV/V: the output at full load per volt of excitation.
Relative resistance change
ΔR/R = 0.5565/350 = 0.00159
Strain
ε = 0.00159/2.12 = 0.00075 = 750 µε
Answer
ε = 750 µε
9.Steady-state error & PID control
Answer: ess = 25
Steady-state error: in a unity-feedback loop with open-loop transfer function G(s) the error is E(s) = R(s)/(1 + G(s)), and by the final value theorem ess = lims→0 s·E(s). The system type is the number of poles of G(s) at s = 0. The error constants are Kp = lim G(s), Kv = lim s·G(s) and Ka = lim s²·G(s), all for s → 0. A step of size A gives ess = A/(1 + Kp), a ramp A·t gives A/Kv and a parabola A·t²/2 gives A/Ka. A type-0 loop follows a step with a finite error, a type-1 loop follows it exactly and a ramp with a finite error.
Acceleration constant
Ka = 2·1/10 = 0.2
Parabola error
ess = 5/0.2 = 25
Answer
ess = 25
10.Steady-state error & PID control
Answer: tp = 1.187 s
P, PI and PID control: the controller C(s) = Kp + Ki/s + Kd·s acts on the error. A proportional gain makes the loop faster and reduces the error of a type-0 plant, but never removes it. The integral term adds a pole at s = 0: the system type rises by one, and a step is followed without error. The derivative term adds damping. To choose gains, write the closed-loop characteristic polynomial and compare it with s² + 2ζωns + ωn². Then %OS = 100·e−ζπ/√(1−ζ²), tp = π/ωd with ωd = ωn√(1 − ζ²), and ts ≈ 4/(ζωn).
Characteristic polynomial
s(s + 6) + 8·2 = s² + 6s + 16
ωₙ and ζ
ωₙ = √16 = 4 rad/s
ζ = 6/(2·4) = 0.75
Peak time
ωd = 4·√(1 − 0.75²) = 2.646 rad/s
tp = π/2.646 = 1.187 s
Answer
tp = 1.187 s
11.Step response
Answer: ts = 1 s
Step response: a first-order system G(s) = K/(τs + 1) answers a step of size U with y(t) = K·U·(1 − e−t/τ): it reaches 63.2 % of the final value K·U after one time constant τ and 98 % after 4τ. A second-order system G(s) = K·ωₙ²/(s² + 2ζωₙs + ωₙ²) has the poles s = −ζωₙ ± jωd with ωd = ωₙ√(1 − ζ²). For 0 < ζ < 1 the step response overshoots: percent overshoot %OS = 100·e−ζπ/√(1−ζ²), peak time tp = π/ωd, and the 2 % settling time ts ≈ 4/(ζωₙ). Compare the denominator with s² + 2ζωₙs + ωₙ² to read off ωₙ and ζ. For a mass–spring–damper ωₙ = √(k/m) and ζ = c/(2√(km)); for a series RLC circuit ωₙ = 1/√(LC) and ζ = (R/2)·√(C/L).
Compare with the standard form
The denominator must match s² + 2ζωₙs + ωₙ².
ωₙ² = 82 → ωₙ = 9.055 rad/s
2ζωₙ = 8 → ζ = 8/(2·9.055) = 0.4417
Result
ζωₙ = 4 → ts ≈ 4/4 = 1 s
Answer
ts = 1 s
12.Step response
Answer: K = 780.9
Step response: a first-order system G(s) = K/(τs + 1) answers a step of size U with y(t) = K·U·(1 − e−t/τ): it reaches 63.2 % of the final value K·U after one time constant τ and 98 % after 4τ. A second-order system G(s) = K·ωₙ²/(s² + 2ζωₙs + ωₙ²) has the poles s = −ζωₙ ± jωd with ωd = ωₙ√(1 − ζ²). For 0 < ζ < 1 the step response overshoots: percent overshoot %OS = 100·e−ζπ/√(1−ζ²), peak time tp = π/ωd, and the 2 % settling time ts ≈ 4/(ζωₙ). Compare the denominator with s² + 2ζωₙs + ωₙ² to read off ωₙ and ζ. For a mass–spring–damper ωₙ = √(k/m) and ζ = c/(2√(km)); for a series RLC circuit ωₙ = 1/√(LC) and ζ = (R/2)·√(C/L).